ROOMS TO GO KIDS CREEKSIDE 2.0 User manual

WARNING DANGER
Failure to follow these warnings and assembly instructions could result in serious
injury or death. To help prevent serious or fatal injuries from entrapment or falls:
-
Read all instructions before assembling bunk bed and keep these instructions for future reference.
-
Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints, missing
parts, or sharp edges. DO NOT Use bunk bed if any parts are missing or broken.
-
DO NOT Use substitute parts. Contact your local Rooms To Go or visit www.ROOMSTOGO.COM
for replacement parts and instructional literature if needed.
-
Follow the information on the warnings appearing on the upper bunk end structure and on the carton,
DO NOT REMOVE WARNING LABEL FROM BED.
-
Always use the recommended size mattress or mattress supports, or both to help prevent the likelihood
of entrapment or falls.
-Ensure thickness of mattress and foundation combine does not exceed
10 inches (255mm
) and
mattress surface is at least
5 inches (127mm)
below upper edge of guardrails.
-
Do not allow children under 6 years of age to use the upper bunk.
-
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
-
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
-
Limit top bunk use to one person.
-
Always use the ladder for entering and leaving the upper bunk.
-
Use of night light may provide added safety precaution for a child using the upper bunk.
-
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
-
The use of water or sleep flotation mattress is prohibited.
-
This bunk bed meets all the requirements of ASTM 1427-19.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed; for example, but not limited to, hooks, belts, and jump ropes.
CREEKSIDE 2.0 COLLECTION
THANK YOU FOR YOUR PURCHASE
11/7/2022 Page 1 of 97

35740403 40G-705 TWIN LOFT END
36840406 40G-707 TWIN CASTER BED HD & FT
P A R T S L I S T
3794440P TWIN/TWIN LOFT W/DESK CHARCOAL
RTG SKU # STYLE # ITEM DESCRIPTION
35540409 40G-706 STEP STORAGE UNIT
38000232 100-645 TW. SLAT PACK (4)
38000232 100-645 TW. SLAT PACK (4)
36640402 40G-730 6 PC RAILS (2 GUARD & 4 SIDE RAILS)
36140402 40G-710 LOFT DESK
3794441P TWIN/TWIN LOFT W/DESK CHESTNUT
RTG SKU # STYLE # ITEM DESCRIPTION
35540411 40B-706 STEP STORAGE UNIT
36640414 40B-730 6 PC RAILS (2 GUARD & 4 SIDE RAILS)
36140414 40B-710 LOFT DESK
35740415 40B-705 TWIN LOFT END
36840418 40B-707 TWIN CASTER BED HD & FT
38000232 100-645 TW. SLAT PACK (4)
38000232 100-645 TW. SLAT PACK (4)
TOOLS NEEDED
11 Pc
51 Pc
24 Pcs
Phillips screwdriver (not included)
5/16"-18 x 3 3/8" Bolt
PARTS LIST QTY PARTS LIST QTY HARDWARE LIST QTY
Twin top bunk bed end
1 Pc
Allen wrench (included)
24 Pc 1 pc bunkbed end twin 5 mm Hex key
61 Pc
16 Pcs
Side rails 6 x 1 1/4"
48 Pc 71 Pc 4 Pcs
Drywall screw
2 Pcs
Guardrails Loft desk 3/8" x 3 1/8"
Metal pin
32 Pc
11/7/2022 Page 50 of 97
Caster bed footboard
Casters
Twin slats Caster bed headboard
81 Pc
A
B
C
D
E

ASSEMBLY INSTRUCTIONS
Assemble loft desk and top bunk bed end.
MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY
11/7/2022 Page 51 of 97
Install slats, one on each end, two equally spaced in the middle,
Assemble top side rails. then fasten with 1 1/4" screws.
Assemble guardrails and tighten all bolts. Assemble side rails
STEP 5
STEP 4
STEP 1
C
D
B
C
A
C
A
A
A
A
A
B
DD
A
B
STEP 2 STEP 3
A
B
A
A
A
A
A
AA
A
B

ASSEMBLY INSTRUCTIONS
11/7/2022 Page 52 of 97
Install slats, one on each end and two equally spaced in the middle,
then fasten with 1 1/4" screws Install casters in headboard and footboard.
Install slats, one on each end and two equally spaced in the middle,
then fasten with 1 1/4" screws
STEP 6
STEP 8
C
CSTEP 7 E
E
E

Twin size mattress- 74" - 75" long and 37-1/2" - 38-1/2" wide
Twin size Bunkie board- 74" long and 37-1/2" wide
Full size mattress- 74" - 75" long and 52-1/2" - 53-1/2" wide
Full size Bunkie board- 74" long and 52-1/2" wide
ASSEMBLY INSTRUCTIONS
11/7/2022 Page 53 of 97
Place Bunkie boards (required, sold separately) on top of the slats
Use only correct mattress dimensions and Bunkie board:
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
STEP 9