Renishaw MH8 User manual

MH8 user's guide
Documentation part number: H-1000-5190-06-B
MH8 user's guide
www.renishaw.com
Issued 02 2020
1

General information
© 2003 ‐ 2020 Renishaw plc. All rights reserved.
This document may not be copied or reproduced in whole or in part, or transferred to any other media or language, by any means, without
the prior written permission of Renishaw.
The publication of material within this document does not imply freedom from the patent rights of Renishaw plc.
Disclaimer
RENISHAW HAS MADE CONSIDERABLE EFFORTS TO ENSURE THE CONTENT OF THIS DOCUMENT IS CORRECT AT THE DATE OF
PUBLICATION BUT MAKES NO WARRANTIES OR REPRESENTATIONS REGARDING THE CONTENT. RENISHAW EXCLUDES LIABILITY,
HOWSOEVER ARISING, FOR ANY INACCURACIES IN THIS DOCUMENT.
Trademarks
RENISHAW, the probe symbol used in the RENISHAW logo and REVO are registered trademarks of Renishaw plc in the United Kingdom and
other countries. apply innovation and names and designations of other Renishaw products and technologies are trademarks of Renishaw
plc or its subsidiaries.
All brand names and product names used in this document are trade names, service marks, trademarks, or registered trademarks of their
respective owners.
All trademarks and trade names are acknowledged.
WEEE
The use of this symbol on Renishaw products and/or accompanying documentation indicates that the product should not be mixed with the
general household waste upon disposal. It is the responsibility of the end user to dispose of this product at a designated collection point for
waste electrical and electronic equipment (WEEE) to enable reuse or recycling. Correct disposal of this product will help save valuable
resources and prevent potential negative effects on the environment. For more information, please contact your local waste disposal service
or Renishaw distributor.
Warranty
Renishaw plc warrants its equipment for a limited period (as set out in our Standard Terms and Conditions of Sale) provided that it is installed
exactly as defined in associated Renishaw documentation.
Prior consent must be obtained from Renishaw if non-Renishaw equipment (e.g. interfaces and/or cabling) is to be used or substituted. Failure
to comply with this will invalidate the Renishaw warranty.
Claims under warranty must be made from authorised service centres only, which may be advised by the supplier or distributor.
MH8 user's guide
www.renishaw.com
Issued 02 2020
2

Care of equipment
Renishaw probes and associated systems are precision tools used for obtaining precise measurements and must therefore be treated with
care.
Changes to Renishaw products
Renishaw reserves the right to improve, change or modify its hardware or software without incurring any obligations to make changes to
Renishaw equipment previously sold.
Packaging
To aid end user recycling and disposal the materials used in the different components of the packaging are stated here:
Packaging component Material 94/62/EC code 94/62/EC number
Outer box Corrugated fibreboard PAP 20
Packaging insert Corrugated fibreboard PAP 20
Bag Low density Polyethylene LDPE 4
MH8 user's guide
www.renishaw.com
Issued 02 2020
3

Product compliance
EU declaration of conformity
Contact Renishaw plc or visit www.renishaw.com/EU for the full EU declaration.
EMC conformity
This equipment must be installed and used in accordance with this installation guide. This product is intended for industrial use only and
should not be used in a residential area or connected to a low voltage power supply network which supplies buildings used for residential
purposes.
REACH regulation
Information required by Article 33﴾1﴿ of Regulation ﴾EC﴿ No. 1907/2006 ﴾“REACH”﴿ relating to products containing substances of very high
concern (SVHCs) is available at:
www.renishaw.com/REACH
China RoHS
Contact Renishaw plc or visit www.renishaw.com/ChinaRoHS for the full China RoHS tabulation.
MH8 user's guide
www.renishaw.com
Issued 02 2020
4

Introduction
The MH8 is a manually operated, indexing probe head that articulates to provide orientation of the stylus. The head can carry probes fitted
with a Renishaw M8 connector. The TP20 and TP6 touch-trigger probes are recommended. The MH8 is available with a range of shanks to suit
the mounting arrangement specified by the manufacturer of the CMM.
MH8 user's guide
www.renishaw.com
Issued 02 2020
5

Product description
The MH8 has 2 axes. The probe connector is carried on the A‐axis which can rotate the probe through 90° in the Z plane. The B‐axis can rotate
the probe through ±180° in the X‐Y plane.
A lever actuated mechanism locks both axes in the desired position for gauging the workpiece. The axes are unlocked to allow free rotation to
another position. The locked positions are set at angular increments of 15° in each axis, providing a total of 168 positions.
When the head orientation is locked, the probe is kinematically constrained in a highly repeatable spatial position. This means that after initial
qualification of the stylus tip, in the positions required for gauging the workpiece, the probe may be reorientated to any of the qualified
positions without the need for requalification.
A red LED is provided on the front of the head to indicate the probe's status. The LED may be driven by the CMM controller or by a Renishaw
probe interface. It is convention for the LED to be ON to indicate a seated (armed) probe and to be OFF to indicate a triggered probe.
Electrical connection is via a 5 pin DIN connector.
MH8 user's guide
www.renishaw.com
Issued 02 2020
6

Part number summary
Part number Description
A-1332-0013 MH8 probe head
A-1332-0002 MH8 probe head + TK4 probe tools (no shank)
A-1332-0003 MH8 + TK4 + MS1 shank
A-1332-0004 MH8 + TK4 + MS2 shank
A-1332-0005 MH8 + TK4 + MS4 shank
A-1332-0006 MH8 + TK4 + MS5 shank
A-1332-0007 MH8 + TK4 + MS7 shank
A-1332-0008 MH8 + TK4 + MS9 shank
A-1332-0009 MH8 + TK4 + MS10 shank
A-1332-0010 MH8 + TK4 + MS13 shank
A-1332-0011 MH8 + TK4 + MS15 shank
A-1332-0014 MH8 + TK4 + MS17 shank
A-1332-0012 MH8 + TK4 + D shank
A-1042-1486 S1 ‘C' spanner
A-1047-3932 S9 double ended ‘C' spanner
M-5000-3540 S7 stylus tightening tool
P-TL03-0150 Hexagon key, 1.5 mm AF (TP2 / TP6 adjustment)
MH8 user's guide
www.renishaw.com
Issued 02 2020
7

Installation procedure
Mounting the shank on the probe head
Hold the shank in the recess on the top face of the MH8
Rotate the shank until the three screw holes are aligned
Fix the shank in place using only the M3 × 5 mm screws ﴾supplied﴿
Progressively tighten using the 2.5 mm A/F hexagon key (supplied)
Mounting the head on the CMM
The head will normally be attached to the quill of the CMM using a standard shank, specified by the CMM manufacturer.
Standard shanks are listed in the ‘Part number summary'.
Special or customised mounting arrangements are possible. Please contact your supplier or Renishaw, for details of our custom products
service.
The mounting must be absolutely rigid, as any movement during normal operation of the head will add errors to the measurement system.
If the head is replaced or repositioned in the quill, it will be necessary to requalify all of the head positions in current use.
Electrical connection
Connection is by means of a 5-pin DIN connector on the side of the head.
The pin numbering functions are given in the table below:
Pin number Designation
1LED cathode
2Ground
3LED anode
4Probe circuit
5Probe circuit
MH8 user's guide
www.renishaw.com
Issued 02 2020
8

Mounting the probe to the probe head
If fitting a TP20 probe, mount the probe body to the probe head before fitting the probe module and stylus.
Screw the threaded end of the probe into the M8 connector on the probe head until it is finger tight
Fit the S1 ‘C' spanner ﴾supplied﴿ to the location holes in the probe body and tighten by hand
The recommended tightening torque is 0.3 Nm - 0.5 Nm
Refer also to the user's guide for the probe type being used.
Extension bars
Probe reach may be extended by 50 mm using a PEL1 extension bar. Use of the PEL2, PEL3 or PE series extension bars is not recommended.
MH8 user's guide
www.renishaw.com
Issued 02 2020
9

Head operation
NOTE: Ensure that the lock lever is turned fully clockwise to the locked position, before taking gauge points.
To change the orientation of the probe
Unlock the head by turning the lock lever to the fully anti-clockwise position
Grip the body of the probe (avoid touching the stylus) and rotate the B-axis until the desired angle indication on the scale (in increments of
15°﴿ is adjacent to the B‐axis reference mark
Rotate the A‐axis until the desired angle indication on the scale ﴾in increments of 15°﴿ is at the A‐axis reference position
Lock the head by turning the lock lever to the fully clockwise position
Qualify the stylus tip(s) according to the CMM supplier's instructions
Change the orientation of the probe to the next desired position and qualify the stylus tip(s)
Repeat the qualification process for all desired orientations and stylus tips
Commence gauging, ensuring that the correct qualification data is recalled for each head position
Periodic requalification should be performed according to the following considerations:
CMM supplier's recommendations, particularly in respect of temperature changes
At the start of the working day or shift
After an accidental collision
After changing any measuring system component (except a prequalified TP20 module)
If the initial state is unknown or uncertain
MH8 user's guide
www.renishaw.com
Issued 02 2020
10

Dimensions
MH8 user's guide
www.renishaw.com
Issued 02 2020
11

Technical specification
Measuring performance
Positional repeatability ﴾2σ﴿
(At stylus tip with TP20 probe, standard force module and 10
mm stylus length)
1.5 μm
Positional repeatability ﴾2σ﴿ with 50 mm extension bar ﴾PEL1﴿
(At stylus tip with TP20 probe, standard force module and 10
mm stylus length)
2.5 μm
Technical data
Range of articulation A‐axis: 0° to 90° in 15° increments
B‐axis: ±180° in 15° increments
Maximum load TP6 - no extension allowed
TP20 or TP2 probe + 50 mm extension (PEL1)
Operating temperature range +10 °C to +40 °C
Storage temperature range ‐10 °C to +70 °C
Probe connector Renishaw M8 × 1.25 mm × 5 mm
Electrical connector 5‐pin DIN ﴾180°﴿
Sealing IP30
Weight 205 g (without shank)
MH8 user's guide
www.renishaw.com
Issued 02 2020
12

Maintenance
This product is intended for use in a protected metrology environment and therefore accumulations of dust or swarf should not occur.
In common with all precision measuring equipment, regular inspection and cleaning are recommended to ensure continued high
performance.
Maintenance is limited to wiping the outer surfaces, axes scale labels and mounting face of the probe connector with a clean, dry cloth or
proprietary cleaning material.
MH8 user's guide
www.renishaw.com
Issued 02 2020
13

Fault finding
Refer also to the appropriate user's guide for the probe.
Loss of measuring accuracy
Possible causes Remedy
Mounting not secure. Check that the MH8 is correctly mounted to the shank and that the
screws are secure. Check the clamping mechanism in the CMM quill.
MH8 not fully locked. Ensure that the lock lever is turned fully clockwise.
Excessive force imparted to probe after locking. Unlock and re-lock the MH8.
MH8 overloaded. Use only with the specified probe and extension combinations.
Faulty probe. Check by substitution.
MH8 worn or damaged. Check by substitution or return to Renishaw or your supplier.
Axes ‘rattle' when rotated
Possible causes Remedy
MH8 not fully unlocked. Turn lock lever fully anticlockwise before attempting to reorientate
probe.
MH8 user's guide
www.renishaw.com
Issued 02 2020
14

For worldwide contact details,
please visit our main website at
www.renishaw.com/contact
Renishaw plc
New Mills, Wotton-under-Edge,
Gloucestershire, GL12 8JR
United Kingdom
T+44 (0)1453 524524
F+44 (0)1453 524901
www.renishaw.com/cmmsupport
Issued 02 2020