Resol deltasol bx plus User manual

*11214319* 11214319
beginning with rmware version 2.07
DeltaSol® BX Plus
Manual
en
Mounting
Connection
Operation
Troubleshooting
Application examples
Manual for the specialised
craftsman
www.resol.com
Thank you for buying this RESOL product.
Please read this manual carefully to get the best performance from this unit.
Please keep this manual safe.
The Internet portal for easy and secure access
to your system data – www.vbus.net

2
en
© 20201013_11214319_DeltaSol_BX_Plus.monen.indd
Safety advice
Please pay attention to the following safety advice in order to avoid danger and
damage to people and property.
Danger of electric shock:
• When carrying out works, the device must rst of all be disconnected from the
mains.
• It must be possible to disconnect the device from the mains at any time.
• Do not use the device if it is visibly damaged!
Instructions
Attention must be paid to the valid local standards, regulations and directives!
Information about the product
Proper usage
The system controller is designed for electronically controlling solar thermal sys-
tems and heating systems in compliance with the technical data specied in this
manual.
Improper use excludes all liability claims.
EU Declaration of conformity
The product complies with the relevant directives and is therefore la-
belled with the CE mark. The Declaration of Conformity is available upon
request, please contact the manufacturer.
Note
Strong electromagnetic elds can impair the function of the controller.
ÎMake sure the controller as well as the system are not exposed to
strong electromagnetic elds.
Target group
These instructions are exclusively addressed to authorised skilled personnel.
Only qualied electricians are allowed to carry out electrical works.
Initial commissioning must be effected by authorised skilled personnel.
Authorised skilled personnel are persons who have theoretical knowledge and ex-
perience with the installation, commissioning, operation, maintenance, etc. of elec-
tric/electronic devices and hydraulic systems and who have knowledge of relevant
standards and directives.
Description of symbols
Warnings are indicated with a warning symbol!
Signal words describe the danger that may occur, when it is not avoided.
WARNING means that injury, possibly life-threatening injury, can oc-
cur.
ÎIt is indicated how to avoid the danger described.
ATTENTION means that damage to the appliance can occur.
ÎIt is indicated how to avoid the danger described.
Note
Notes are indicated with an information symbol.
ÎArrows indicate instruction steps that should be carried out.
Disposal
• Dispose of the packaging in an environmentally sound manner.
• At the end of its working life, the product must not be disposed of as urban waste.
Old appliances must be disposed of by an authorised body in an environmental-
ly sound manner. Upon request we will take back your old appliances
bought from us and guarantee an environmentally sound disposal of the
devices.
Subject to technical change. Errors excepted.

3
en
DeltaSol® BX Plus
The DeltaSol® BX Plus is the most versatile system controller for complex solar
and heating systems. It is ideal to control a combination of solar and non-solar parts
of the system.
Easy combination and parameterisation of pre-programmed functions for several
millions of hydraulic variants.
Contents
1 Overview ............................................................................................... 4
2 Installation ............................................................................................ 5
2.1 Mounting ......................................................................................................................... 5
2.2 Electrical connection .................................................................................................... 7
2.3 Data communication / Bus .......................................................................................... 9
2.4 SD card slot .................................................................................................................... 9
3 Step-by-step parameterisation ........................................................... 9
4 Operation and function ..................................................................... 10
4.1 Buttons ..........................................................................................................................10
4.2 Selecting menu points and adjusting values ..........................................................10
4.3 Adjusting the timer ....................................................................................................12
4.4 Adjusting optional functions .....................................................................................14
4.5 Output submenu ................................................................................ 16
4.6 Sensorconguration.......................................................................... 18
5 Commissioning................................................................................... 19
5.1 Basic systems ................................................................................................................20
5.2 Overview of output and sensor allocation ............................................................ 21
6 Main menu .......................................................................................... 35
6.1 Menu structure ............................................................................................................ 36
7 Status................................................................................................... 37
7.1 Measured / Balance values .........................................................................................37
7.2 Solar ............................................................................................................................... 37
7.3 Arrangement ................................................................................................................ 37
7.4 Heating ........................................................................................................................... 37
7.5 HQM ..............................................................................................................................37
7.6 Messages ........................................................................................................................37
7.7 Home screen ................................................................................................................38
8 Solar..................................................................................................... 38
8.1 Basic setting .................................................................................................................. 38
8.2 Optional functions ...................................................................................................... 41
8.3 Function control .......................................................................................................... 51
8.4 Holiday function ........................................................................................................... 52
8.5 Solar expert menu ......................................................................................................53
9 Arrangement ...................................................................................... 54
9.1 Optional functions ...................................................................................................... 54
10 Heating................................................................................................ 62
10.1 Shared relays .................................................................................................................62
10.2 Heating circuits ............................................................................................................64
10.3 Optional functions ......................................................................................................73
10.4 Screed drying ................................................................................................................77
11 HQM .................................................................................................... 78
12 Basic settings ...................................................................................... 80
13 SD card................................................................................................ 80
14 Manual mode ...................................................................................... 81
15 User code ............................................................................................ 82
16 Inputs / Modules................................................................................... 82
16.1 Modules .........................................................................................................................82
16.2 Inputs ..............................................................................................................................82
17 Troubleshooting.................................................................................. 84
18 Accessories ......................................................................................... 87
19 Index .................................................................................................... 89

4
en
1 Overview
• 5 relay outputs and 8 inputs for Pt1000, Pt500 or KTY temperature
sensors
• Up to 2 extension modules viaVBus®(21 sensors and 15 relays in
total)
• Inputs for digital Grundfos Direct Sensors™ as well as for FRHd
humidity sensors
• Integratedcontrolofupto2high-efciencypumpsviaPWMoutputs
• Data logging, storing, easy transfer of controller adjustments pre-
paredandrmwareupdatesviaSDcard
• Cooling over the heating circuit with condensation detection
• Dew point calculation by means of the FRH(d) humidity sensor to
avoid condensation
• Simpliedtimer,0-10VboilercontrolandDHWpreheating
• Remote access to the heating circuits with room control unit(s) or
the VBus®Touch HC App
• Extended optional functions, e.g. solid fuel boiler function with mixer
and target temperature control
Technical data
Inputs: 8 Pt1000, Pt500 or KTY temperature sensor inputs (can optionally be
used for remote controls, operating mode switches or potential-free switches), 1
impulse input for V40 owmeters (can optionally be used for Pt1000, Pt500 or KTY
temperature sensors, remote controls, operating mode switches or potential-free
switches), 1 CS10 solar cell, 2 digital inputs for VFD/RPD Grundfos Direct SensorsTM
or FRHd humidity sensors
Outputs: 5 relays, 4 of them semiconductor relays for speed control, 1 potential-free
relay, 2 PWM outputs (switchable to 0-10 V)
PWM frequency: 512 Hz
PWM voltage: 10.5 V
Switching capacity:
1 (1) A 240 V~ (semiconductor relay)
4 (2) A 24 V⎓ / 240 V~ (potential-free relay)
Total switching capacity: 4 A 240 V~
Power supply: 100 – 240 V~ (50 – 60 Hz)
Supply connection: type X attachment
Standby: 0.91 W
Temperature controls class: VIII
Energyefciencycontribution: 5 %
Mode of operation: type 1.B.C.Y action
Rated impulse voltage: 2.5 kV
Data interface: VBus®, SD card slot
VBus®current supply: 60 mA
Functions: 7 integrated calorimeters and control of weather-compensated heating
circuits. Adjustable system parameters and add-on options (menu-driven), balance
and diagnostics functions, function control according to VDI 2169
Housing: plastic, PC-ABS and PMMA
Mounting: wall mounting, also suitable for mounting into patch panels
Indication / Display: full graphic display
Operation: 7 buttons
Ingress protection: IP 20 / EN 60529
Protection class: I
Ambient temperature: 0 … 40 °C
Degree of pollution: 2
Dimensions: 198 x 170 x 43 mm

5
en
2 Installation
2.1 Mounting
WARNING! Danger of electric shock!
Upon opening the housing, live parts are exposed!
ÎAlways disconnect the device from power supply be-
fore opening the housing!
Note
Strong electromagnetic elds can impair the function of the device.
ÎMake sure the device as well as the system are not exposed to strong
electromagnetic elds.
The device must only be located in dry interior rooms.
If the device is not equipped with a mains connection cable and a plug, the device
must additionally be supplied from a double pole switch with contact gap of at least
3 mm.
Please pay attention to separate routing of sensor cables and mains cables.
In order to mount the device to the wall, carry out the following steps:
ÎUnscrew the crosshead screw from the cover and remove it along with the
cover from the housing.
ÎMark the upper fastening point on the wall. Drill and fasten the enclosed wall
plug and screw leaving the head protruding.
ÎHang the housing from the upper fastening point and mark the lower fastening
points (centres 150 mm).
ÎInsert lower wall plugs.
ÎFasten the housing to the wall with the lower fastening screws and tighten.
ÎCarry out the electrical wiring in accordance with the terminal allocation (see
page 7).
ÎPut the cover on the housing.
ÎAttach with the crosshead screw.
Dimensions and minimum distances
170
198
43

6
en
12
4
3
56
Chap. 2.2

7
en
T4A
100 ... 240 V~
50-60 Hz
R1-R4 1 (1) A (100 ... 240) V~
R5 4 (1) A 240 V~
4 (1) A 24V
R5
R4
R3
R2
R1
L' L
N
R5
S1
S8
CS
S7
S6
S5
S4
S3
S2
10
S9/IMP1
VBus
GND
Temp. Sensor
VBus
GND
IP20
1
1
1
DeltaSol BX Plus
Made in Germany
N
!
PWM/0-10V
2.2 Electrical connection
WARNING! Danger of electric shock!
Upon opening the housing, live parts are exposed!
ÎAlways disconnect the device from power supply
before opening the housing!
ATTENTION! ESD damage!
Electrostatic discharge can lead to damage to electronic com-
ponents!
ÎTake care to discharge properly before touching
the inside of the device!To do so, touch a grounded
surface such as a radiator or tap!
Note
Connecting the device to the power supply must always be the last step
of the installation!
Note
The Speed option must be set to Off when non-speed-controlled
devices such as valves are connected.
Note
It must be possible to disconnect the device from the mains at any time.
ÎInstall the mains plug so that it is accessible at any time.
ÎIf this is not possible, install a switch that can be accessed.
If the mains cable is damaged, it must be replaced by a special connection
cable which is available from the manufacturer or its customer service.
Do not use the device if it is visibly damaged!
The controller is equipped with 5 relays in total to which loads such as pumps,
valves, etc. can be connected:
Relays 1 … 4 are semiconductor relays, designed for pump speed control:
Conductor R1 … R4
Neutral conductor N (common terminal block)
Protective earth conductor ⏚ (common terminal block)
Relay 5 is a potential-free relay.
Depending on the product version, mains cables and sensor cables are already con-
nected to the device. If that is not the case, please proceed as follows:
Attach exible cables to the housing with the enclosed strain relief and the corre-
sponding screws.
The temperature sensors (S1 to S8) have to be connected to the terminals S1
to S8 and GND (either polarity).
The cables carry low voltage and must not run together in a cable conduit with
cables carrying a voltage higher than 50 V (please pay attention to the valid local
regulations). The cable lentghs depend on the cross sectional area.
Example: up to 100 m at 1.5 mm², up to 50 m at 0.75 mm². The cables can be ex-
tended with a two-wire cable.

8
en
The V40 owmeter can be connected to the terminals S9 / IMP1 and GND (either
polarity).
Connect the irradiation sensor CS10 to the terminals CS10 and GND with cor-
rect polarity. To do so, connect the cable marked GND to the GND common ter-
minal block, the cable marked CS to the terminal marked CS10.
The terminals marked PWM / 0-10V are control outputs for high-efciency pumps
(for connection see illustration).
Electricalconnectionofahigh-efciencypump(HE pump)
Speed control of a HE pump is possible via a PWM signal / 0-10 V control. The pump
has to be connected to the relay (power supply) as well as to one of the PWM out-
puts of the controller. In the Output adjustment channel one of the PWM control
types as well as a relay have to be selected (see page 16).
R5
R4
R3
R2
R1
L' L
N
R5
A |B
PWM/0-10V
PWM PWM1
PWM2
GND
GND
+ +
GND
Note
When Grundfos Direct SensorsTM are used, connect the sensor ground
common terminal block to PE.
Connect the digital Grundfos Direct Sensors™ or FRHd humidity sensors
to the Gd1 and Gd2 inputs.
The controller is supplied with power via a mains cable. The power supply of the
device must be 100 … 240 V~ (50 … 60 Hz).
Connect the mains cable to the following terminals:
Neutral conductor N
Conductor L
Protective earth conductor ⏚ (common terminal block)
WARNING!
Danger of electric shock!
L' is a fused contact permanently carrying voltage.
ÎAlways disconnect the device from power supply
before opening the housing!
Conductor L' (L' is not connected with the mains cable. L' is a fused contact
permanently carrying voltage.)
Note
For more details about the commissioning procedure see page 9.
Power supply
Pump
Power
supply
230 V~
blue brown
yellow/green

9
en
2.3 Data communication / Bus
The controller is equipped with a VBus® for data transfer and energy supply to
external modules. The connection is to be carried out at the terminals marked
VBus (any polarity).
One or more VBus® modules can be connected via this data bus, such as:
• DL2 / DL3 Datalogger
• KM2 Communication module
• VBus®/USB or VBus®/LAN interface adapters
Different solutions for visualisation and remote parameterisation are available on
the website www.resol.com. On the website, rmware updates are also available.
Note
During remote parameterisation, the  symbol will be displayed, the con-
troller will not carry out any control function.
Note
For more information about accessories, see page 87.
2.4 SD card slot
The controller is equipped with an SD card slot.
With an SD card, the following functions can be carried out:
• Store measurement and balance values onto the SD card. After
the transfer to a computer, the values can be opened and visual-
ised, e.g. in a spreadsheet.
• Prepare adjustments and parameterisations on a computer and
transfer them via the SD card.
• Store adjustments and parameterisations on the SD card and, if necessary, re-
trieve them from there.
• Download rmware updates from the Internet and install them on the controller.
Note
For more information about using an SD card, see page 80.
3 Step-by-step parameterisation
The DeltaSol® BX Plus is a controller that offers a broad variety of functions
to the user. At the same time, the user has a lot of freedom in congurating them.
Therefore, to set up a complex system, careful planning is required. We recommend
drawing a sketch of the system rst.
If planning, hydraulic construction and electrical connection have all been carried
out successfully, proceed as follows:
1. Running the commissioning menu
After the commissioning menu has been nished (see page 19), further adjust-
ments can be made. The commissioning menu can be repeated any time by means
of a reset (see page 79). Additional adjustments will be deleted.
For further information about the commissioning menu see page page 19.
2. Registering sensors
If owmeters, ow switches, Grundfos Direct Sensors™, flow rate sensors, humidi-
ty sensors, room control units, remote controls, switches and/or external extension
modules are connected, these have to be registered in the Inputs/Modules menu.
For further information about the registration of modules and sensors see page 82.
In some functions, the Sensorcong. channel is available for sensor selection, in
which sensors not used and not registered can be selected. The selected sensor
input will automatically be set to the sensor type required for the function.
3. Activating optional functions and/or heating circuits
The basic solar system has been adjusted during commissioning. Now, optional
functions and/or heating circuits can be selected, activated and adjusted.
Outputs available can be allocated to functions which require an output. The con-
troller always suggests the numerically smallest output available.
Sensors can be allocated to more than one function.
For further information about the solar optional functions see page 41.
For further information about the optional arrangement functions see page 54.
For further information about heating circuits and optional heating functions see
page 64.

10
en
4 Operation and function
4.1 Buttons
The controller is operated via the 7 buttons next to the display. They have the
following functions:
Button ❶ - scrolling upwards
Button ❸ - scrolling downwards
Button ❷ - increasing adjustment values
Button ❹ - reducing adjustment values
Button ➄ - conrming
Button ➅ - entering the status menu / chimney sweeper mode (system-dependent)
Button ➆ - escape button for changing into the previous menu / to the holidays menu
(press and hold down for 5 s)
Operating control LED (in the directional pad)
Green: Everything OK
Red: Cancellation screed drying
Red ashing: Sensor fault / initialisation / chimney sweeper function active
Green ashing: Manual mode / screed drying active
4.2 Selecting menu points and adjusting values
During normal operation of the controller, the display is in the main menu. If no
button is pressed for 1 min, the display illumination switches off. After 4 further
minutes, the controller will display the home screen (see page 38).
Press any key to reactivate the display illumination.
ÎIn order to scroll through a menu or to adjust a value, press either buttons ❶
and ❸ or buttons ❷ and ❹.
ÎTo open a submenu or to conrm a value, press button ➄.
ÎTo enter the status menu, press button ➅ – unconrmed adjustments will not
be saved.
ÎTo enter the previous menu, press button ➆ – unconrmed adjustments will
not be saved.
If no button has been pressed within a couple of minutes, the adjustment is can-
celled and the previous value is retained.
If the symbol » is shown behind a menu item, pressing button ➄ will open a new
submenu.
If the symbol ➕ is shown in front of a menu item, pressing button ➄ will open a
new submenu. If it is already opened, a ➖ is shown instead of the ➕.

11
en
current value savedminimum value maximum value
adjusted value
(not yet conrmed)
adjustment channel
Values and options can be changed in different ways:
Numeric values can be adjusted by means of a slide bar. The minimum value is indi-
cated to the left, the maximum value to the right. The large number above the slide
bar indicates the current adjustment. By pressing buttons ❷ or ❹ the upper slide
bar can be moved to the left or to the right.
Only after the adjustment has been conrmed by pressing button ➄ will the num-
ber below the slide bar indicate the new value. The new value will be saved if it is
conrmed by pressing button ➄ again.
active area inactive area
When 2 values are locked against each other, they will display a reduced adjustment
range depending on the adjustment of the respective other value.
In this case, the active area of the slide bar is shortened, the inactive area is indicated
as a dotted line. The indication of the minimum and maximum values will adapt to
the reduction.
If only one item of several can be selected, they will be indicated with radio buttons.
When one item has been selected, the radio button in front of it is lled.
If more than one item of several can be selected, they will be indicated with check-
boxes. When an item has been selected, an x appears inside the checkbox.

12
en
4.3 Adjusting the timer
When the Timer option is activated, a timer is in-
dicated in which time frames for the function can be
adjusted.
In the Day selection channel, the days of the week
are available individually and as frequently selected
combinations.
If more than one day or combination is selected, they
will be merged into one combination for the following
steps.
The last menu item after the list of days is Continue.
If Continue is selected, the timer menu opens, in which
the time frames can be adjusted.
Adding a time frame:
In order to add a time frame, proceed as follows:
ÎSelect New time frame.
ÎAdjust Start and Stop for the desired time frame.
The time frames can be adjusted in steps of 5 min.
ÎIn order to save the time frame, select Save and
conrm the security enquiry with Ye s .
ÎIn order to add another time frame, repeat the
previous steps.
6 time frames can be adjusted per day or com-
bination.
ÎPress the left button (⟲) in order to get back to
the day selection.

13
en
Copying a time frame:
In order to copy time frames already adjusted into an-
other day / another combination, proceed as follows:
ÎChoose the day / the combination into which the
time frames are to be copied and select Copy
from.
A selection of days and / or combinations with time
frames will appear.
ÎSelect the day or combination from which the
time frames are to be copied.
All time frames adjusted for the selected day or com-
bination will be copied.
If the time frames copied are not changed, the day or
combination will be added to the combination from
which the time frames have been copied.
Changing a time frame:
In order to change a time frame, proceed as follows:
ÎSelect the time frame to be changed.
ÎMake the desired change.
ÎIn order to save the time frame, select Save and
conrm the security enquiry with Ye s .
Removing a time frame:
In order to delete a time frame, proceed as follows:
ÎSelect the time frame that is to be deleted.
ÎSelect Delete and conrm the security enquiry
with Ye s .

14
en
Resetting the timer:
In order to reset time frames adjusted for a certain day
or combination, proceed as follows:
ÎSelect the desired day or combination.
ÎSelect Reset and conrm the security enquiry
with Ye s .
The selected day or combination will disappear from
the list, all its time frames will be deleted.
In order to reset the whole timer, proceed as follows:
ÎSelect Reset and conrm the security enquiry
with Ye s .
All adjustments made for the timer are deleted.
4.4 Adjusting optional functions
In the Optional functions / Add new function menus, optional functions can be
selected and adjusted.
The kind and number of optional functions offered depends on the previous ad-
justments.
When a function is selected, a submenu opens in which all adjustments required
can be made.
In this submenu, an output and, if necessary, certain system components can be
allocated to the function.
If an output can be allocated to the function, the Output submenu opens (see
page 14).
When a function has been adjusted and saved, it will appear in the Opt. functions
menu above the menu item Add new function.

15
en
This allows an easy overview of functions already saved.
An overview about which sensor has been allocated to which component and
which output has been allocated to which function is given in the Status menu.
At the end of each optional function submenu, the menu items Funct. and Save
function are available. In order to save a function, select Save function and con-
rm the security enquiry by selecting Ye s .
In functions already saved, the menu item Delete function will appear instead.
In order to delete a function already saved, select Delete function and conrm
the security enquiry by selecting Yes. The function will become available under Add
new function again. The corresponding outputs will be available again.
With the menu item Funct., an optional function already saved can be temporarily
deactivated or re-activated respectively. In this case, all adjustments will remain
stored, the allocated outputs will remain occupied and cannot be allocated to an-
other function. The allocated sensor will be monitored for faults.
By selecting Switch, the function can be activated or deactivated respectively by
means of an external potential-free switch.
If Switch is selected, the channel Sensor appears, in which a sensor input can be
dened as a switch.

16
en
4.5 Output submenu
The Output submenu is available in almost all optional functions. Therefore, it will
not be explained in the individual function descriptions.
In this submenu, relays and / or signal outputs can be allocated to the function se-
lected. All adjustments required for the outputs can be made in this menu.
All controller and module (if connected) outputs available will be displayed.
Adjustments Result
Relay option PWM/0-10 V option Speed control Adapter option Behaviour of the relay
output
Behaviour of the signal
output Behaviour of the adapter
Ye s Ye s Ye s Ye s
Î
On/Off Modulating Modulating
Ye s No Ye s No
Î
Burst control -Modulating
Ye s No Ye s Ye s
Î
On/Off -Modulating
Ye s No No irrelevant*
Î
On/Off -0 % / 100 %
Ye s Ye s Ye s No
Î
On/Off Modulating 0 % / 100 %
Ye s Ye s Ye s Ye s
Î
On/Off Modulating Modulating
Ye s Ye s No irrelevant*
Î
On/Off 0 % / 100 % 0 % / 100 %
No Ye s Ye s irrelevant*
Î
-Modulating -
No Ye s No irrelevant*
Î
-0 % / 100 % -
*If the relay option and / or speed control is deactivated, the adjustment in the adapter option will have no effect.
Adjustment
channel Description Adjustment range / selection Factory setting
Relay Relay option Yes, No No
Relay Relay selection system dependent system dependent
PWM/0-10 V PWM/0-10 V option Yes, No No
Output Signal output selection system dependent system dependent
Signal Signal type PWM, 0-10 V PWM
Prole Curve Solar, Heating Solar
Speed Speed control Yes, No system dependent
Min. Minimum speed 20 … 100 % 30 %
Max. Maximum speed 20 … 100 % 100 %
Adapter Adapter option Yes, No No
Inverted Inverted switching option Yes, No No
Blocking
protect. Blocking protection option Yes, No No
Manual mode Operating mode Max., Auto, Min., Off Auto
If - is selected, the function will run normally in the software but will not operate
an output. Relay and signal outputs can be activated separately. Depending on the
adjustments made, the following results are possible:

17
en
Speed control
In the Speed adjustment channel, the speed control for the output can be acti-
vated or deactivated respectively. If Ye s is selected, the channels Min., Max. and
Adapter will appear.
In the Min. adjustment channel, a relative minimum speed for a pump connected
can be allocated to the output
In the Max. adjustment channel, a relative maximum speed for a pump connected
can be allocated to the output.
If the speed control signal is generated via a VBus® / PWM interface adapter, the
Adapter option has to be activated. If Ye s is selected, the relay will switch on or
off (no burst control). Speed information will be transmitted via the VBus®.
For functions controlling loads which are not speed controlled, the speed control
will not be shown on the display (e.g. the bypass type, mixer).
If the temperature difference reaches or exceeds the switch-on temperature differ-
ence, the pump switches on at 100 % speed for 10 s. Then, the speed is reduced to
the minimum pump speed value. If the temperature difference exceeds the adjusted
set value by 1/10 of the rise value, the pump speed increases by one step (1 %). The
response of the controller can be adapted via the parameter Rise. Each time the
difference increases by 1/10 of the adjustable rise value, the pump speed increases
by one step until the maximum pump speed of 100% is reached. If the temperature
difference decreases by 1/10 of the adjustable rise value, pump speed will be de-
creased by one step.
100
90
80
70
60
50
40
30
20
10
0
0 246810 12 14 16 18 20 22 24
Temperature difference
Pump speed [%]
40
39
38
37
36
35
34
33
32
31
30
10,0 10,2 10,4 10,6 10,8 11 11,2 11,4 11,6 11,8 12
Te mperaturdifferenz Kollektor – Speicher [K]
Pumpendrehzahl [%]
Temperature difference collector – store [K]
Pump speed [%]
Detail

18
en
Relay option
If the Relay option is activated, a relay can be allocated to the output selection.
PWM/0-10 V option
If the PWM/0-10 V option is activated, a PWM/0-10 V output can be allocated to
the output selection.
In the Signal channel, a selection between a PWM or a 0-10 V signal can be made.
In the Prole channel, characteristic curves for solar and heating pumps can be
selected.
Signalcharacteristic:PWM;Prole:Solar
Speed Solar (S)
Output
100%0% PWM/0-10 V
100%
Signalcharacteristic:PWM;Prole:Heating
Speed Heating (H)
Output
100%0% PWM/0-10 V
100%
Blocking protection
In order to protect the pumps against blocking after standstill, the controller is
equipped with a blocking protection option. This option can be activated in the
output selection submenu. The Blocking protection option can be adjusted in the
Basic settings / Blocking protect. menu (see page 79).
Manual mode
In the Manual mode adjustment channel, the operating mode of the output can be
selected. The following options are available:
Off = Output is switched off (manual mode)
Min. = Output is active at minimum speed (manual mode)
Max. = Output is active at 100 % (manual mode)
Auto = Output is in automatic mode
Note
After service and maintenance work, the operating mode must be set back
to Auto. In manual mode the control logic is overridden.
4.6 Sensorconguration
Some sensors must be registered and congured in the Inputs/Modules menu
(see page 9 and
page 82 ).
In some functions, the Sensorcong. channel is available for sensor selection, in
which sensors not used and not registered can be selected. The selected sensor
input will automatically be set to the sensor type required for the function. Regis-
tering the sensor in the Inputs/Modules menu is then no longer necessary.
Note
If a sensor is used as the temperature sensor of a function, the sensor
types Switch, Fern, BAS, Impulse and none will not be available for
the corresponding input.

19
en
5 Commissioning
When the hydraulic system is lled and ready for operation, connect the controller
to the mains.
The controller runs an initialisation phase in which the directional pad glows red.
When the controller is commissioned or when it is reset, it will run a commis-
sioning menu after the initialisation phase. The commissioning menu leads the user
through the most important adjustment channels needed for operating the system.
Commissioning menu
The commissioning menu consists of the channels described in the following. In or-
der to make an adjustment, press button ➄. Adjust the value by pressing buttons ❹
and ❷, then push button ➄ to conrm. The next channel will appear in the display.
5
5
Adjustment mode
Button navigation
Changing a value
Conrming a value
next parameter appears auto-
matically
2
4
1. Language:
ÎAdjust the desired menu language.
2. Units:
ÎAdjust the desired unit system.
4. Time:
ÎAdjust the clock time. First of all adjust the hours,
then the minutes.
5. Date:
ÎAdjust the date. First of all adjust the year, then the
month and then the day.
3. Daylight savings time adjustment:
ÎActivate or deactivate the automatic daylight sav-
ings time adjustment.
6. Selection: System or Scheme
ÎChoose whether the controller is to be cong-
ured with a scheme number or with a system and
a variant.

20
en
8. Completing the commissioning menu:
After the system has been selected or the scheme
number has been entered, a security enquiry appears.
If the security enquiry is conrmed, the adjustments
will be saved.
ÎIn order to conrm the security enquiry, press
button ➄.
ÎIn order to reenter the commissioning menu
channels, press button ➆. If the security enquiry
has been conrmed, the controller will be ready
for operation.
Note
The adjustments carried out during commis-
sioning can be changed anytime in the corre-
sponding adjustment channel. Additional func-
tions and options can also be activated and
adjusted (see page 35).
Set the code to the customer code be-
fore handing over the controller to the
customer (see page 81).
5.1 Basic systems
The controller is pre-programmed for different basic systems. The selection de-
pends on the number of heat sources (collector elds) and heat sinks (stores, pool).
The selection of the basic solar system is one of the most important adjustments
and is thus requested already in the commissioning menu.
First, the number of collector elds and stores will have to be adjusted, then the
hydraulic variant.
Note
A solar system with store loading in layers is implemented as a 2-store
system (store top = store 1; store base = store 2).
The system selected is visualised by the corresponding number of store and col-
lector symbols. The exemplary gure shows system 2.3.x with 2 collector elds
and 2 stores.
The hydraulic variant refers to the different actuators that are to be controlled.
They are visualised on the display by means of symbols, when the variant is selected.
The upper symbol indicates the actuator belonging to the collector elds, the lower
one the actuators belonging to the stores.
The exemplary gure shows the display indicated when system 2.3.2 has been se-
lected.
In this case, each collector eld has a 2-port valve, the stores are loaded by means
of pump logic.
The controller allocates corresponding output and sensor settings for each basic
system. The allocations of all combinations are shown in chap. 5.2.
7a. Scheme (if 6. = Scheme):
ÎEnter the scheme number of the desired system.
7b. Selection of the solar system (if 6. = System):
ÎAdjust the desired solar system (number of collec-
tors and stores, hydraulic variants).