Resource Oslo Series User manual

Assembly
Instructions
Oslo

OSLO
Oslo 173
Oslo 301
Oslo 1

WARNING
READ CAREFULLY BEFORE BEGINNING INSTALLATION.
IMPROPER INSTALLATION OF THE PRODUCT MAY CAUSE SERIOUS INJURY.
Warranties for all products purchased from Resource Furniture, LLC
are only valid if the product has been properly assembled , installed by a
trained professional, and operated in accordance with the assembly instructions.
Resource Furniture accepts no responsibility
for any damage or injury caused by improper installation.
XInstallation must be performed by a licensed contractor or a trained professional, who will
ensure proper assembly and installation.
XInstallation must be performed by at least 2 people.
XImproper installation of this product can cause serious or fatal injury.
XImproper Installation may result in permanent damage to the bed.
XAll hardware must be properly tightened. No parts of the model should be left loose or unstable
Oslo 2

CODE QUANTITY COMPONENT
1 1 Right Side Panel
2 1 Left Side Panel
3 1 Top Horizontal Panel
4 1 Base
5 2 Left/Right Small Side Panels (already attached to parts 1 & 2)
6 1 Right Back Panel
7 1 Left Back Panel
8 1 Bedframe
9 1 Mattress Support Bar
10 1 Shelf
11 1 Sofa Underseat Storage Box
12 1 Padded Sofa Seat
13 1 Sofa Seat Extension
14 1 Padded Sofa Backrest
15 1 Right Armrest
16 1 Left Armrest
STRUCTURAL PARTS - OSLO 301
Oslo 3

ASSEMBLY OF THE STRUCTURE
Oslo 301
Oslo 4

CODE QUANTITY COMPONENT
1 1 Right Side Panel
2 1 Left Side Panel
3 1 Top Horizontal Panel
4 1 Base
5 2 Left/Right Small Side Panels (already attached to parts 1 & 2)
6 1 Right Back Panel
7 1 Left Back Panel
8 1 Bedframe
9 1 Mattress Support Bar
10 1 Shelf
11 1 Sofa Underseat Storage Box
12 1 Padded Sofa Seat
14 1 Padded Sofa Backrest
17 1 Right 60 mm Armrest
18 1 Left 60 mm Armrest
STRUCTURAL PARTS - OSLO 173
Oslo 5

ASSEMBLY OF THE STRUCTURE
Oslo 173
Oslo 6

QUANTITY COMPONENT
13mm Allen Wrench
14mm Allen Wrench
15mm Allen Wrench
18mm Allen Wrench
TOOL KIT - ALL VERSIONS
CODE QUANTITY COMPONENT DESCRIPTION
A 13 7 x 36 6MA Pins
B 13 D15 L17 Cam Connectors
C 7 3.5 x 20 Screws for back panels
D 4 5MA x 50 TPSE Screws for side panels
E 6 4MA x 18 TBCE Screws for mattress support bar
F 4 4 x 40 Screws to attach top panel
G 2 Screws to secure sofa levers
H 2 8MA Nuts to secure sofa levers
I 4 6MA x 20
J 4 D8 x 18 Washers to secure sofa levers
K 4 6MA x 25 Screws for storage box
STRUCTURAL HARDWARE - ALL VERSIONS
Oslo 7

Boiserie Panel
Boiserie Shelves (287mm)
Boiserie Shelves (327mm) Boiserie Box
CODE DESCRIPTION
MMetal Shelf Pins
NBoilts for Shelf Pins
OBoiserie Bar
PWall Anchors
BOISERIE PANEL HARDWARE
Oslo 8

ASSEMBLY OF THE STRUCTURE
IMAGE 1
Attach the 2 left side panel to the 4 base using 2 D screws.
IMAGE 2
Attach the 7 left back panel to the 2 left side panel using 3 A pins and 3 B cam connectors.
Attach the 6 right back panel to the 7 left back panel with 3 A pins and 3 B cam connectors.
A
B
These pieces
are pre-assembled.
A
Oslo 9

ASSEMBLY OF THE STRUCTURE
IMAGE 3
Attach the 3 top horizontal panel to the 2 left side panel with 2 A pins and 2 Bcam connectors, and to
the back panels with 4 F screws.
B
A
F
Oslo 10

ASSEMBLY OF THE STRUCTURE
IMAGE 4
Attach the 1 right side panel to the 4 base using 2 D screws, and to the top horizontal panel and back
panels with 5 Apins and 5 Bcam connectors
Secure the back panels to the base using 7 Cscrews.
These pieces
are pre-assembled.
c
c
c
c
c
c
c
Oslo 11

ASSEMBLY OF THE BED FRAME
IMAGE 5
Unscrew the saftey plates fixed to the 4 structure base, as shown in det. 5a.
Oslo 12

ASSEMBLY OF THE BED FRAME
IMAGE 6
Position the 8 bed frame within the structure as shown. Place the levers located near the head of the bed
frame into their slots as shown in det. 6a, and re-attach the safety plates from Image 5.
Ensure that pins on the bedframe slide into the base of the structure as shown in det. 6b.
Note: It is recommended to lay out a blanket/towel around the work area, under the bedframe, so
that the metal feet do not scratch the oor.
Oslo 13

ASSEMBLY OF THE BED FRAME
IMAGE 7
Attach the 9 mattress support bar to the bed frame using six E screws.
Oslo 14

ASSEMBLY OF THE BED FRAME
IMAGE 8
Lift the 8 bed frame into its upright vertical position.
Screw the base pin to the lever cords, leaving the screw on the outer side. Pass the cord under the pulleys
on the base 4 and secure the pins on the appropriate seat.
Oslo 15

ATTACHING THE SHELF
IMAGE 9
Attach the 10 shelf to the feet of the bedframe, using the 6 screws attached to the shelf, as shown.
Oslo 16

OPENING THE BED
IMAGE 10
Grasp the handle in the center of the shelf and pull down the bed, gently accompanying the bed with both
hands until it reaches the ground.
Oslo 17

ASSEMBLY OF THE BED & HEADBOARD
IMAGE 11
Attach the headboard (if purchased by client) to the back of the structure.
Secure the mattress to the bedframe by fastening the two buckled straps.
Oslo 18

ASSEMBLY OF THE BED
IMAGE 12
To balance the bedframe, adjust the spring tension controllers with the 8mm allen wrench provided. Turn
clockwise to adjust the tension in order to close the bed with ease. ensuring that each side of the bed-
frame is adjusted equally.
Note: An excessive number of turns may damage the cable.
Oslo 19