Resource Altea 90 User manual

Assembly
Instructions
Altea 90/120 Board

WARNING
READ CAREFULLY BEFORE BEGINNING INSTALLATION.
IMPROPER INSTALLATION OF THE PRODUCT MAY CAUSE SERIOUS INJURY
Warranties for all products purchased from Resource Furniture, LLC are
only valid if the product has been properly assembled, Installed by a trained
professional, and operated in accordance with the assembly instructions.
Resource Furniture accepts no responsibility for any damage or injury caused
by Improper Installation.
Installation must be performed by a licensed contractor or a trained
professional, who will ensure proper assembly and installation.
Installation must be performed by at least 2 people.
Improper installation may result in permanent damage to the bed.
Improper installation of this product can cause serious or fatal injury.
No anchor can be used twice. If the product is removed from the wall, new
anchor holes must be drilled and new hardware must be used.
All hardware must be properly tightened. No parts of the model should be
left loose or unstable.
The wall bed must be secured to the wall in four locations using appropriate
hardware. The contractor or installer must select the proper anchoring hardware.
• The wall anchors included are for solid concrete walls only.
• Walls with wooden studs: Wood screws must be screwed into wooden studs in
the wall.
• Any other wall composition: A proper wall anchor suitable for the wall’s
construction must be selected by the contractor or installer.

ALTEA 90 MATTRESS SPECIFICATIONS
Recommended weight 31-35lbs
Recommended dimensions: 33 1/2”x 78” x 7”
ALTEA 120 MATTRESS SPECIFICATIONS
Recommended weight: 46-51lbs
Recommended dimensions: 45” x 78” x 7” 1
ALTEA 90/120 BOARD OVERVIEW

ALTEA 90/120 BOARD OVERVIEW
2

ALTEA 90/120 BOARD OVERVIEW
Lower the right lever completely and verify that the
two locking pins at the bottom of the bed base retract
an equal distance and do so symmetrically. Repeat by
operating the left lever.
3

ALTEA 90/120 BOARD ADJUST THE LOCKING CABLE
1. Loosen the locking nut as shown in the picture,
Use a 10mm open end wrench..
2. To have the pin go in more, turn the head of the
cable (turn clockwise ) as showed in the picture ,
using a 8mm open end wrench. By turning the cable,
you are extending the distance the lever can move.
Be careful not to loosen the cable too much, the
cable can become disconnected from the lever.
3. To lock the cable. Hold the head of the cable with
the 8mm wrench while tightening the locking nut.
1. Loosen the locking nut as shown in the picture,
Use a 10mm open end wrench..
HOW TO ADJUST THE LOCKING CABLE FOR MODEL PENELOPE/CIRCE/ALTEA
2. To have the pin go in more, turn the head of
the cable (turn clockwise ) as showed in the
picture , using a 8mm open end wrench. By turning
the cable, you are extending the distance the lever
can move.
Be careful not to loosen the cable too much, the
cable can become disconnected from the lever.
3. To To lock the cable. Hold the head of the cable
with the 8mm wrench while tightening the
locking nut.
1. Loosen the locking nut as shown in the picture,
Use a 10mm open end wrench..
HOW TO ADJUST THE LOCKING CABLE FOR MODEL PENELOPE/CIRCE/ALTEA
2. To have the pin go in more, turn the head of
the cable (turn clockwise ) as showed in the
picture , using a 8mm open end wrench. By turning
the cable, you are extending the distance the lever
can move.
Be careful not to loosen the cable too much, the
cable can become disconnected from the lever.
3. To To lock the cable. Hold the head of the cable
with the 8mm wrench while tightening the
locking nut.
4

ALTEA 90/120 BOARD COMPONENTS
CODE QT Y. COMPONENTS
1 1 Right vertical panel
2 1 Left vertical panel
3 1 Top horizontal panel
4 1 Bottom horizontal panel
5 1 Bed frame
6 1 Back panels
7 1 Mattress support bar
8 1 Desk
9 2 Desk mechanism
ALTEA 90/120 BOARD TOOLS
QTY. DESCRIPTION
1 Allen wrench 4 MM
1 Allen wrench 5 MM
1 Allen wrench 6 MM
5

ALTEA 90/120 BOARD STRUCTURAL HARDWARE
Note: The installer must determine the composition of the wall and appropriate anchors
prior to installation. The wall anchors included are for solid concrete walls only. 6

STRUCTURE ASSEMBLY
7

STRUCTURE ASSEMBLY
8

9
OPTIONAL WAND LIGHTING
Wand Lighting
Installation Guideline for Altea/Telemaco
•Optional light fixture must be installed before headboard
• Drill 1/2” hole at 10 1/4” above headboard and 1 1/2” in from the side
• Install mounting Plate with provided wood screws, aligning the 1/2” drill holes
Wand Light Exploded Diagram
Cord Length = 118”
Front
Back
7• Optional light fixture must be installed before headboard (see page 20-21 for details)
• Drill 1/2” hole at 10 1/4” above headboard and 1 1/2” in from the side
• Install mounting Plate with provided wood screws, aligning the 1/2” drill holes

LEVELING THE STRUCTURE
8Ensure that the structure is level and plumb. To compensate for any floor unevenness,
use the adjustable feet on the bottom panel to level the structure.
10

9
WALL BED ATTACHMENT
1
2
3 4
1 2
3
4
1 2
3
4
1
2
3 4
After the unit is level and plumb it should be securely attached to the wall using the
metal angle mounting brackets as shown in the images below. A proper wall anchor
suitable for the wall’s construction must be selected by the contractor or installer.
11

MATTRESS BAR INSTALLATION
10 Mattress bar must be installed before the bed base is inserted into the structure.
12

BED BASE INSTALLATION
13

BED BASE INSTALLATION
BED BASE INSTALLATION
Clack
G
x4
close
12
13
18
14

DESK INSTALLATION
15

DESK INSTALLATION
16

DESK INSTALLATION
17

HEADBOARD AND MATTRESS INSTALLATION
Open the bed to place the mattress and secure it with the straps
14
19
18
MATTRESS INSTALLATION