Resource Swing 0 User manual

Assembly
Instructions
Swing 0

WARNING
READ CAREFULLY BEFORE BEGINNING INSTALLATION.
IMPROPER INSTALLATION OF THE PRODUCT MAY CAUSE SERIOUS INJURY
Warranties for all products purchased from Resource Furniture, LLC are
only valid if the product has been properly assembled, Installed by a trained
professional, and operated in accordance with the assembly instructions.
Resource Furniture accepts no responsibility for any damage or injury caused
by Improper Installation.
Installation must be performed by a licensed contractor or a trained
professional, who will ensure proper assembly and installation.
Installation must be performed by at least 2 people.
Improper installation may result in permanent damage to the bed.
Improper installation of this product can cause serious or fatal injury.
All hardware must be properly tightened. No parts of the model should be
left loose or unstable.

SWING 0 MATTRESS SPECIFICATIONS
Recommended weight: ~ 64 lbs
Recommended dimensions: 79 1/2 x 60 x 7” 1
SWING 0 OVERVIEW
86 5/8
86 5/8
68 1/8
68 1/8
68 1/8
49 1/4
86 5/8 68 1/8

2
SWING 0 OVERVIEW

3
SWING 0 OVERVIEW

SWING 0 COMPONENTS
CODE QT Y. COMPONENTS
1 1 Right side panel
2 1 Left side panel
3 1 Top horizontal panel
4 1 Base
5 2 Left/Right Small Side Panels (already attached to 1 & 2)
6 1 Right Back Panel
7 1 Left Back Panel
8 1 Bed Frame
9 1 Mattress Support Bar
10 1 Front Shelf
11 1 Sofa Seat & Storage Box
12 1 Wooden trim pieces - horizontal
13 1 Wooden trim pieces - vertical
4

SWING 0 STRUCTURAL HARDWARE
CODE QT Y. COMPONENT DESCRIPTION
A 13 7 x 36 6MA Pins
B 13 D15 L17 Cam Connectors
C 7 3.5 x 20 Wood screws for back
panels
D 4 5MA x 50 Machine bolt for side panels
E 6 4MA x 18 Machine bolt for mattress
support bar
F 4 4 x 40 Wood screws for attaching top
panel to back panels
G 4 4 x 25 Machine bolt for front shelf
07
SWING 0
07
SWING 0
5

STRUCTURE ASSEMBLY
1
2
Attach the (2) left side panel to the (4) base using 2 (D) screws.
Attach the (7) left back panel to the (2) left side panel using 3 (A) pins and 3 (B) cam connectors.
Attach the (6) right back panel to the (7) left back panel with 3 (A) pins and 3 (B) cam connectors.
6

7
STRUCTURE ASSEMBLY
B
B
A
A
F
F
3
4
Attach the (3) top horizontal panel to the (2) left side panel with 2 (A) pins and
2 (B) cam connectors, and to the back panels with 4 (F) screws.
Attach the (1) right side panel to the (4) base using 2 (D) screws, and to the top horizontal panel
and back panels with 5 (A) pins and 5 (B) cam connectors. Secure the back panels to the base
using 4 (F) screws. These pieces are pre-assembled.

Wand Light Exploded Diagram
Cord Length = 118”
Back
Front
5
OPTIONAL WAND LIGHTING
Drill 1/2” hole at 18 1/8” below upperbed structure panel (from inside) and 1 1/2” in from
the side. Install mounting plate with provided wood screws, aligning the 1/2” drill holes.
8

9
LEVELING THE STRUCTURE
det.1
4a
6Ensure that the structure is level and plumb. To compensate for any floor unevenness,
use the adjustable feet on the bottom panel (det. 1 4a) to level the structure.

7
8
BED FRAME ASSEMBLY
det.5a
Unscrew the safety plates fixed to the (4) base, as shown in det. 5a. The safety plates
must be securely reattached after the levers are inserted. (see next page for details)
Position the (8) bed frame within the structure as shown. Place the levers located near the head
of the bed frame into their slots as shown in det. 6a, and re-attach the safety plates from Image 5.
Ensure that pins on the bedframe slide into the base of the structure as shown in det. 6b.
Note: It is recommended to USE proper floor protection around the work area, under the bed
frame, so that the metal feet do not scratch the floor.
det.6b
det.6a
10

11
BED FRAME ASSEMBLY
9Attach the (9) mattress support bar to the bed frame using six (E) machine bolts.

12
BED FRAME ASSEMBLY
10 Lift the (8) bed frame into its upright vertical position. Screw the base pin to the lever
cords, leaving the screw on the outer side. Pass the cord under the pulleys on the base
(4) and secure the pins on the appropriate seat.

11
12
FRONT SHELF INSTALLATION
BED OPERATION
17
Installing the shelf
IMG.9: Attach the shelf to the feet of the bedframe, as shown, using 4 (I) screws.
OPENING THE BED
IMAGE 10:
Grasp the handle in the center of the shelf and pull down the bed, gently accompanying the
bed with both hands until it reaches the ground.
Attach the shelf to the feet of the bed frame, as shown, using 4 (I) screws.
Grasp the handle in the center of the shelf and pull down the bed, gently accompanying
the bed with both hands until it reaches the ground.
13

MATTRESS & HEADBOARD INSTALLATION
13 Attach the headboard (if purchased by client) to the back of the structure. Secure the
mattress to the bedframe by fastening the two buckled straps.
14

BED FRAME ADJUSTMENT
18
ADJUSTING THE TENSION ON THE BED FRAME SPRINGS
IMAGE 12
To balance the bedframe, adjust the spring tension controllers with the 8mm allen wrench
provided. Turn clockwise to adjust the tension in order to close the bed with ease. Ensuring that
each side of the bedframe is adjusted equally.
Note: An excessive number of turns may damage the cable.
ASSEMBLY OF THE BED & HEADBOARD
IMAGE 11
Attach the headboard (if purchased by client) to the back of the structure.
Secure the mattress to the bedframe by fastening the two buckled straps.
14 To balance the bedframe, adjust the spring tension controllers with the 8mm allen
wrench provided. Turn clockwise to adjust the tension in order to close the bed with
ease. Ensuring that each side of the bedframe is adjusted equally.
Note: An excessive number of turns may damage the cable.
15

SOFA SEAT & STORAGE BOX INSTALLATION
15 Attach the sofa storage box (11) to the base (4) using n°4 machine bolts 6MAx25.
Installing the sofa seat and storage box
IMG.22: Attach the sofa storage box (11) to the base (4) using (M) machine bolts..
22
16

WOOD TRIM PIECES INSTALLATION
16 Attach the wooden trim pieces(12,13) to the base using the pre installed adhesive strip.
INSTALLING THE WOOD TRIM PIECES
IMG.32: Attach the wooden trim pieces(12,13) to
the base using the pre installed adhesive strip.
SWING 0
20
17

18
OPENING YOUR SWING 0 BED
Nuovoliola Swing 0
SAFELY OPERATING YOUR
SWING 0 BED
Grasp the handle located in the middle
of the shelf and pull with one hand, while
supporting the top of the bed frame with
the other as you walk backwards, allowing
the bed frame to descend under control.
Make sure to support the bed frame with
both hands for the entire descent until the
shelf is firmly resting on the floor.
It may be necessary to gently push down
on the bed frame for the final few inches.
Release the two mattress straps by
squeezing the center of the clasp.
Tuck the straps under the mattress.
Sleep!
Prior to opening bed, remove any items
taller than approx. 12.”
Remove back cushions.
To store the cushions or bedding under
seat, lift sofa seat from bottom front edge
for Swing 0.
If you have a coee table, push table against
sofa. DO NOT STAND ON TABLE! If you cannot
reach shelf, move table aside.
Make sure that any and all items on shelf
are stable and secure at all times.
1
2
3
4
5
18