Resource Kali 90 User manual

Assembly
Instructions
Kali Sofa 90/120

WARNING
READ CAREFULLY BEFORE BEGINNING INSTALLATION.
IMPROPER INSTALLATION OF THE PRODUCT MAY CAUSE SERIOUS INJURY
Warranties for all products purchased from Resource Furniture, LLC are
only valid if the product has been properly assembled, Installed by a trained
professional, and operated in accordance with the assembly instructions.
Resource Furniture accepts no responsibility for any damage or injury caused
by Improper Installation.
Installation must be performed by a licensed contractor or a trained
professional, who will ensure proper assembly and installation.
Installation must be performed by at least 2 people.
Improper installation may result in permanent damage to the bed.
Improper installation of this product can cause serious or fatal injury.
No anchor can be used twice. If the product is removed from the wall, new
anchor holes must be drilled and new hardware must be used.
All hardware must be properly tightened. No parts of the model should be
left loose or unstable.
The wall bed must be secured to the wall in four locations using appropriate
hardware. The contractor or installer must select the proper anchoring hardware.
• The wall anchors included are for solid concrete walls only.
• Walls with wooden studs: Wood screws must be screwed into wooden studs in
the wall.
• Any other wall composition: A proper wall anchor suitable for the wall’s
construction must be selected by the contractor or installer.

KALI SOFA 90 MATTRESS SPECIFICATIONS
Recommended weight: ~ 36 lbs
Recommended dimensions: 31 1/2” x 78” x 7”
KALI SOFA 120 MATTRESS SPECIFICATIONS
Recommended weight: ~ 50 lbs
Recommended dimensions: 41” x 78” x 7” 1
KALI SOFA 90/120 OVERVIEW
Kali 120 Sofa
Kali 90 Sofa
Wide Arms

2
KALI SOFA 90/120 OVERVIEW

3
KALI SOFA 90/120 OVERVIEW

KALI SOFA 90/120 COMPONENTS
CODE QT Y. COMPONENTS
1 1 Right side panel
2 1 Left side panel
3 1 Top horizontal panel
4 1 Bottom horizontal panel
5 1 Bed frame
6 1 Back panels
7 1 Headboard
8 1 Metal mattress support bar
9 1 Sofa frame
10 1 Padded sofa seat
11 2 Sofa armrests
12 2 Metal plates for sofa frame
13 2 Triangular reinforcement plates
4

5
KALI SOFA 90/120 WALL MOUNTING HARDWARE
CODE QT Y. DESCRIPTION
WA 4Wall anchors supplied anchors are
for solid concrete walls only
WA 2 Wall brackets
WA 4 Bracket screws
KALI SOFA 90/120 TOOLS
QTY. DESCRIPTION
1 Allen wrench 4 MM
1 Allen wrench 6 MM
Note: The installer must determine the composition of the wall and appropriate anchors
prior to installation. The wall anchors included are for solid concrete walls only.

6
KALI SOFA 90/120 STRUCTURAL HARDWARE
CODE QT Y. DESCRIPTION
A 8 Pins
B 8 Cam connectors
C 22 Phillips screw
D 4 Hex screws - for attaching bed frame
to structure
M 10 Hex Screw - for attaching sofa frame
to structure
N 4 Conical Washer - for attaching sofa
frame to structure and sofa armrests
O 4 Hex Screw - for attaching triangular
sofa plates to structure
P 4 Phillips Screw - for triangular sofa
reinforcement plates
Q 12 Washers
R 6 Dowels - for attaching sofa armrests
to structure
S 2 Metal Plate - for attaching sofa arm-
rests to structure
T 2 Threaded Rod - for attaching sofa
armrests to structure
U 8 Hex Nut - for attaching sofa
armsrests to structure

77
1
STRUCTURE ASSEMBLY
Screw 8 (A) connector bolts into the (1) right vertical and (2) left vertical panels. Attach the (3)
horizontal top and (4) horizontal bottom panels to the vertical panels by inserting and tightening
8 (B) cams. Attach the (6) back panel to the structure with 22 (C) Phillips screws.

8
Wand Light Exploded Diagram
Cord Length = 118”
Front
Back
2
OPTIONAL KALI 90 WAND LIGHTING
Drill 1/2” hole at 37 7/8” measured from the bottom of the structure (from inside) and 1 1/2” in
from the side. Install mounting Plate with provided wood screws, aligning the 1/2” drill holes.

9
Wand Lighting
Installation Guideline for Kali 120
• Drill 1/2” hole at 37 7/8” measured from the bottom of the structure (from inside) and 1
1/2” in from the side.
• Install mounting Plate with provided wood screws, aligning the 1/2” drill holes
Wand Light Exploded Diagram
Cord Length = 118”
Front
Back
3
OPTIONAL KALI 120 WAND LIGHTING
Drill 1/2” hole at 37 7/8” measured from the bottom of the structure (from inside) and 1 1/2” in
from the side. Install mounting Plate with provided wood screws, aligning the 1/2” drill holes.

10
LEVELING THE STRUCTURE
det.2a
4Ensure that the structure is level and plumb. To compensate for any floor unevenness, use
the adjustable feet on the (4) horizontal bottom panel (det. 2a) to level the structure.

11
5
6
WALL BED ATTACHMENT
Locate the two open spaces at the top of the 6 back panel. Draw a line through the open space
along the top 3 panel as shown in Image 3 to mark where the wall anchors will be placed.
Move the structure away from the wall and attach the WB wall bracket to the wall using 2 WA wall
anchors. The installer must determine the composition of the wall and appropriate anchors prior to
installation. The WA wall an¬chors included are for solid concrete walls only.

12
7
8
WALL BED ATTACHMENT
Re-position the structure against the wall, ensuring that the 2 wall brackets pass through the open
spaces in the back panel. Attach the bracket to the bottom of the top horizontal panel by screwing 1
(WA) screw into each bracket as shown. Do not fasten completely.
Adjust the position of the structure, ensuring that it is level and plumb. Secure each bracket to the
structure by fastening the screws to the top panel completely, using an additional WA screw.

13
9
BED BASE INSTALLATION
det.7a
Fasten the 8 mattress support bar to the 5 bed frame using the 5MA x 20 screws attached to the
bar. Mattress bar must be installed before the bed base is inserted into the structure.

10
SOFA FRAME INSTALLATION
det.8a
Attach the 2 (12) metal plates to the (5) bed frame with 6 (M) hex screws, as shown below.
14

11
BED FRAME INSTALLATION
det.9a
det.9a
Position and insert the (5) bed frame within the structure as shown in det. 9a.
15

16
BED FRAME INSTALLATION
12 Close the lower bed and fasten 2 D hex screws into the mechanisms on both vertical
panels, as shown in det. 10a.

17
13
SOFA BASE INSTALLATION
det.11a
Ensure that the upper and lower bed frames are locked in their upright positions. Align the holes
at the back of the (9) sofa frame with those on the (12) metal plates. Secure into place by using 2
(M) hex screws and 2 (N) conical washers, as shown in det. 11a.

18
SOFA BASE INSTALLATION
14 Insert 6 (R) dowels into the top three holes on both the left and right vertical panels. Insert
and secure the (T) threaded rods into the lowest hole on both the left and right vertical panels.
Position the 2 (11) armrests in front of the left and right panels, lining up the holes on the
armrests with the dowels and rods.