Resource Kali Duo Sofa User manual

Assembly
Instructions
Kali Duo Sofa

WARNING
READ CAREFULLY BEFORE BEGINNING INSTALLATION.
IMPROPER INSTALLATION OF THE PRODUCT MAY CAUSE SERIOUS INJURY
Warranties for all products purchased from Resource Furniture, LLC are
only valid if the product has been properly assembled, Installed by a trained
professional, and operated in accordance with the assembly instructions.
Resource Furniture accepts no responsibility for any damage or injury caused
by Improper Installation.
Installation must be performed by a licensed contractor or a trained
professional, who will ensure proper assembly and installation.
Installation must be performed by at least 2 people.
Improper installation may result in permanent damage to the bed.
Improper installation of this product can cause serious or fatal injury.
No anchor can be used twice. If the product is removed from the wall, new
anchor holes must be drilled and new hardware must be used.
All hardware must be properly tightened. No parts of the model should be
left loose or unstable.
The wall bed must be secured to the wall in four locations using appropriate
hardware. The contractor or installer must select the proper anchoring hardware.
• The wall anchors included are for solid concrete walls only.
• Walls with wooden studs: Wood screws must be screwed into wooden studs in
the wall.
• Any other wall composition: A proper wall anchor suitable for the wall’s
construction must be selected by the contractor or installer.

KALI DUO SOFA MATTRESS SPECIFICATIONS
Recommended weight: ~ 31-35 lbs
Recommended dimensions: 31 1/2” x D 77 1/2” x H 7” 1
KALI DUO SOFA OVERVIEW

2
KALI DUO SOFA OVERVIEW

3
KALI DUO SOFA COMPONENTS
CODE QT Y. COMPONENTS
1 1 Right side panel
2 1 Left side panel
3 1 Top horizontal panel
4 1 Bottom horizontal panel
5 1 Lower Bed frame
6 1 Upper Bed frame
7 2 Back panels
8 1 Upper back panel (IN only)
9 1 Structural Shelf (IN only)
10 1 Upper storage cabinet door (IN only)
11 2 Metal bars for mattresses
12 2 Headboards
15 1 Ladder
16 1 Left (long) padded barrier
17 1 Right (short) padded barrier
18 1 Sofa frame
19 1 Padded sofa seat
20 2 Sofa armrests
21 2 Metal plates for sofa frame
22 2 Triangular reinforcement plates for sofa frame

4
KALI DUO SOFA WALL MOUNTING HARDWARE
CODE QT Y. DESCRIPTION
WA 3Wall anchors supplied anchors are
for solid concrete walls only
WA 3 Wall brackets
WA 18 Bracket screws
KALI DUO SOFA TOOLS
QTY. DESCRIPTION
1 Allen wrench 4 MM
1 Allen wrench 6 MM
Note: The installer must determine the composition of the wall and appropriate anchors
prior to installation. The wall anchors included are for solid concrete walls only.

5
KALI DUO SOFA STRUCTURAL HARDWARE
CODE QT Y. DESCRIPTION
A 12 Pins
B 12 Cam connectors
C44 Phillips screw
D 8 Hex screws - for attaching bed frame
to structure
M 10 Hex Screw - for attaching sofa frame
to structure
N 4 Conical Washer - for attaching sofa
frame to structure and sofa armrests
O 4 Hex Screw - for attaching triangular
sofa plates to structure
P 4 Phillips Screw - for triangular sofa
reinforcement plates
Q 12 Washers
R 6 Dowels - for attaching sofa armrests
to structure
S 2 Metal Plate - for attaching sofa arm-
rests to structure
T 2 Threaded Rod - for attaching sofa
armrests to structure
U 6 Hex Nut - for attaching sofa
armsrests to structure
V 2 Metal Brackets

6
1
STRUCTURE ASSEMBLY
Screw 8 (A) pins into the (1) right vertical and (2) left vertical panels. Attach the (4) horizontal
bottom panel ; (3) horizontal top panel and (9) structural shelf to the vertical panels by inserting
and tightening 12 (B) cams. Attach the (7) back panels to the structure with 22 (C) Phillips screws.

77
Wand Lighting
Installation Guideline for Kali Duo
Wand Light Exploded Diagram
Cord Length = 118”
Front
Back
• Drill 1/2” hole at 37 7/8” measured from the bottom of the structure (from inside) and 1
1/2” in from the side.
• Drill 1/2” hole at 69 1/8” measured from the bottom of the structure (from inside) and 1
1/2” in from the side.
2
OPTIONAL WAND LIGHTING
Drill 1/2” hole at 37 7/8” measured from the bottom of the structure (from inside) and 1 1/2” in
from the side. Drill 1/2” hole at 69 1/8” measured from the bottom of the structure (from inside)
and 1 1/2” in from the side.

8
LEVELING THE STRUCTURE
det.2a
3Ensure that the structure is level and plumb. To compensate for any floor unevenness, use
the adjustable feet on the (4) horizontal bottom panel (det. 2a) to level the structure.