Resource Kali Board 90 User manual

Assembly
Instructions
Kali Board 90/120

WARNING
READ CAREFULLY BEFORE BEGINNING INSTALLATION.
IMPROPER INSTALLATION OF THE PRODUCT MAY CAUSE SERIOUS INJURY
Warranties for all products purchased from Resource Furniture, LLC are
only valid if the product has been properly assembled, Installed by a trained
professional, and operated in accordance with the assembly instructions.
Resource Furniture accepts no responsibility for any damage or injury caused
by Improper Installation.
Installation must be performed by a licensed contractor or a trained
professional, who will ensure proper assembly and installation.
Installation must be performed by at least 2 people.
Improper installation may result in permanent damage to the bed.
Improper installation of this product can cause serious or fatal injury.
No anchor can be used twice. If the product is removed from the wall, new
anchor holes must be drilled and new hardware must be used.
All hardware must be properly tightened. No parts of the model should be
left loose or unstable.
The wall bed must be secured to the wall in four locations using appropriate
hardware. The contractor or installer must select the proper anchoring hardware.
• The wall anchors included are for solid concrete walls only.
• Walls with wooden studs: Wood screws must be screwed into wooden studs in
the wall.
• Any other wall composition: A proper wall anchor suitable for the wall’s
construction must be selected by the contractor or installer.

KALI BOARD 90 MATTRESS SPECIFICATIONS
Recommended weight: ~ 36 lbs
Recommended dimensions: 31 1/2” x 78” x 7” 1
KALI BOARD 90/120 OVERVIEW
Kali 90 Board
Kali 120 Board
KALI BOARD 120 MATTRESS SPECIFICATIONS
Recommended weight: ~ 50 lbs
Recommended dimensions: 41” x 78” x 7”

2
KALI BOARD 90/120 OVERVIEW

3
KALI BOARD 90/120 OVERVIEW

KALI BOARD 90/120 COMPONENTS
CODE QT Y. COMPONENTS
1 1 Right side panel
2 1 Left side panel
3 1 Top horizontal panel
4 1 Bottom horizontal panel
5 1 Bed frame
6 1 Back panels
7 1 Headboard
8 1 Metal mattress support bar
9 2 Desk brackets
10 1 Desk
4
KALI BOARD 90/120
WALL MOUNTING HARDWARE
CODE QT Y. DESCRIPTION
WA 4
Wall anchors supplied
anchors are for solid
concrete walls only
WA 2 Wall brackets
WA 4 Bracket screws
Note: The installer must determine the composition of the wall and appropriate anchors
prior to installation. The wall anchors included are for solid concrete walls only.

5
KALI BOARD 90/120 STRUCTURAL HARDWARE
CODE QT Y. DESCRIPTION
A 8 Pins
B 8 Cam connectors
C 22 Phillips screw
D 4 Hex screws - for attaching
bed frame to structure
E 4 Flanged screws - for attaching
desk to desk mechanism
F 2 Conical Washers - for attaching
desk mechanism to side panels
G 2 Flanged screws - for attaching desk
mechanism to vertical side panels
H 4 Bolt - for attaching desk
I 4 Nut - for attaching desk
L 2 Screw - for attaching desk

6
1
STRUCTURE ASSEMBLY
Screw 8 (A) connector bolts into the (1) right vertical and (2) left vertical panels. Attach the (3)
horizontal top and (4) horizontal bottom panels to the veritcal panels by inserting and tightening
8 (B) cams. Attach the (6) back panel to the structure with 22 (C) Phillips screws.

7
Wand Light Exploded Diagram
Cord Length = 118”
Front
Back
2
OPTIONAL KALI 90 WAND LIGHTING
Drill 1/2” hole at 37 7/8” measured from the bottom of the structure (from inside) and 1 1/2” in
from the side. Install mounting Plate with provided wood screws, aligning the 1/2” drill holes.

8
Wand Lighting
Installation Guideline for Kali 120
• Drill 1/2” hole at 37 7/8” measured from the bottom of the structure (from inside) and 1
1/2” in from the side.
• Install mounting Plate with provided wood screws, aligning the 1/2” drill holes
Wand Light Exploded Diagram
Cord Length = 118”
Front
Back
3
OPTIONAL KALI 120 WAND LIGHTING
Drill 1/2” hole at 37 7/8” measured from the bottom of the structure (from inside) and 1 1/2” in
from the side. Install mounting Plate with provided wood screws, aligning the 1/2” drill holes.

9
LEVELING THE STRUCTURE
det.2a
4Ensure that the structure is level and plumb. To compensate for any floor unevenness, use
the adjustable feet on the (4) horizontal bottom panel (det. 2a) to level the structure.

10
5
6
WALL BED ATTACHMENT
Locate the two open spaces at the top of the 6 back panel. Draw a line through the open space
along the top 3 panel as shown in Image 3 to mark where the wall anchors will be placed.
Move the structure away from the wall and attach the WB wall bracket to the wall using 2 WA wall
anchors. The installer must determine the composition of the wall and appropriate anchors prior to
installation. The WA wall an¬chors included are for solid concrete walls only.

11
7
8
WALL BED ATTACHMENT
Re-position the structure against the wall, ensuring that the 2 wall brackets pass through the open
spaces in the back panel. Attach the bracket to the bottom of the top horizontal panel by screwing 1
(WA) screw into each bracket as shown. Do not fasten completely.
Adjust the position of the structure, ensuring that it is level and plumb. Secure each bracket to the
structure by fastening the screws to the top panel completely, using an additional WA screw.

12
9
BED BASE INSTALLATION
det.7a
Fasten the 8 mattress support bar to the 5 bed frame using the 5MA x 20 screws attached to
the bar. Mattress bar must be installed before the bed base is inserted into the structure.

13
10
BED BASE INSTALLATION
det.8a
det.8a
Position and insert the (5) bed frame within the structure as shown in det. 8a.

14
BED BASE INSTALLATION
11 Close the lower bed and fasten 2 (D) hex screws into the mechanisms on both vertical
panels, as shown in det. 9a.

15
12
DESK INSTALLATION
det.10a
Open the bed by pressing down on one of the two locking levers located on the sides of the bed
frame. Position the (9) desk brackets so that they face towards the structure, as shown below.
Fasten the brackets to the bed frame with 4 (E) flanged screws, as shown in det. 10a.

16
DESK INSTALLATION
det.11a
det.11b
13 Bring the two bracket arms to the vertical panels, aligning the holes. Place the (F) conical washer
between each panel and L-shaped bracket as shown in det. 11a - the conical washer’s smallest
diameter should face away from the panel so that it can fit within the L-shaped bracket. Secure
the L-shaped brackets in place by screwing in a (G) flanged screw into the brackets and panels, as
shown in det. 11b.

17
14
DESK INSTALLATION
Close the lower bed frame. Position the (10) desk against the front of the structure so that it rests
on top of the (9) brackets. The rounded corners should face outwards.

18
DESK INSTALLATION
det.13b
det.13a
15 Insert 4 (H) bolts into the holes on the desk, making sure that they pass through both the desk and
the bracket arms (det. 13a). Once the bolts have been inserted, attach 4 (I) nuts, as shown in det.
13b. Tighten the hardware so that the nut head sits within the hole of the desk. Insert 2 (L) screws
into the two remaining holes on the underside of the desk.