Resource LGM User manual

Assembly
Instructions
LGM

WARNING
READ CAREFULLY BEFORE BEGINNING INSTALLATION.
IMPROPER INSTALLATION OF THE PRODUCT MAY CAUSE SERIOUS INJURY
Warranties for all products purchased from Resource Furniture, LLC are
only valid if the product has been properly assembled, Installed by a trained
professional, and operated in accordance with the assembly instructions.
Resource Furniture accepts no responsibility for any damage or injury caused
by Improper Installation.
Installation must be performed by a licensed contractor or a trained
professional, who will ensure proper assembly and installation.
Installation must be performed by at least 2 people.
Improper installation may result in permanent damage to the bed.
Improper installation of this product can cause serious or fatal injury.
No anchor can be used twice. If the product is removed from the wall, new
anchor holes must be drilled and new hardware must be used.
All hardware must be properly tightened. No parts of the model should be
left loose or unstable.
The wall bed must be secured to the wall in four locations using appropriate
hardware. The contractor or installer must select the proper anchoring hardware.
• The wall anchors included are for solid concrete walls only.
• Walls with wooden studs: Wood screws must be screwed into wooden studs in
the wall.
• Any other wall composition: A proper wall anchor suitable for the wall’s
construction must be selected by the contractor or installer.

1
LGM OVERVIEW
Cannot be installed on carpets or area
rugs, if using an area rug it should be
placed a minimum of 18 1/2” from front
edge of the LGM.
LGM 01 LGM Tavolo

2
LGM OVERVIEW
2

3
LGM OVERVIEW
3

4
LGM OVERVIEW

5
LGM STRUCTURAL HARDWARE
5
CODE QT Y. COMPONENT DESCRIPTION
A100 04 L20 Wood screw
B50 3.5 L30 Wood screw
C 6 3.5 L16 Wood screw
D 8 06 L30 Machine screw
E 6 06 L35 Machine screw
F 6 10mm L45 Machine bolt
G 4 Round washer
H 1 Connected knobs
I 2 Washer with flat edge
J 8 7x36x6 Metal pin
K 8 D15 L17 Cam connector
L 2 Brass bolt
M 1 Top guide pin
N 4 Wall mounting bracket
5

6
1
STRUCTURE ASSEMBLY
Screw 8 metal pins (J) into the side vertical panels. (Part A) Fit the Left side to the Base.
Tighten cam connectors (K) to the metal pins. (Part B).
Part A Part B

7
2
STRUCTURE ASSEMBLY
Install the left back panel into the bed structure with the groove facing the center. Use Wood
Screw 3.5x30 (B) to attach Backpanel. Install the brown spline into the groove. Bed also available
with wide vertical sides. Not shown in these instructions.

8
STRUCTURE ASSEMBLY
3Install the second back panel. Do Not Use any Wood Screws Yet. Attach the top to the left
side using cam connectors (K).

9
STRUCTURE ASSEMBLY
4Attach the right vertical side to the bottom and top using cam connectors (K). Install the
remaining screws into the back panels using wood screws 3.5 L30 (B).

10
STRUCTURE ASSEMBLY
5Move bed structure to the determined installation location and adjust the structure to
be level and plumb. The section of baseboard behind the bed can be removed in order
to mount bed flush to the wall.

11
LEVELING THE FEET
6To compensate for any floor unevenness, use the adjustable feet on the horizontal bottom
panel. Adjust the feet by locating the access hole and use the 4mm allan key. Turn clockwise to
push the leveler down, and counterclockwise to pull the leveler up.

12
7
WALL BED ATTACHMENT
1
2
3 4
1 2
3
4
1 2
3
4
1
2
3 4
After the unit is level and plumb it should be securely attached to the wall using the
metal angle mounting brackets as shown in the images below. A proper wall anchor
suitable for the wall’s construction must be selected by the contractor or installer.
Caution: The included wall anchors are for solid concrete walls only.

13
STRUCTURE THE ROTATING STRUCTURE
8Ensure the height dierence between the rotating arm and the base of the structure is
3mm. Adjust bolts if necessary.
Fasten the rotating arm to
the base of the bed structure
using the brass bolt (L)

14
STRUCTURE THE ROTATING STRUCTURE
9Insert the pin of the “U” shaped metal extrusion into the hole located in the LEFT panel of
the revolving bookshelf. Fasten “U” shaped extrusion with two 3.5 L15 Wood Screws (C).

15
STRUCTURE THE ROTATING STRUCTURE
10
Adjust lower guide pin up.
Later this will be lowered into guide slot

16
STRUCTURE THE ROTATING STRUCTURE
11 Assemble rotating structure to the front of the metal base using three 10mm L45 machine
bolts (F) and two round washers (I) and one washer with flat edge (I).
Note: Attach the bolts (F) just snug, as the left panel will need adjustment later.

17
STRUCTURE THE ROTATING STRUCTURE
12
13
Stand the structure and base upright and install the 2nd panel.
Install the 6 bolts previously removed, but do not tighten all the way.

18
STRUCTURE THE ROTATING STRUCTURE
14 Install the top of the rotating unit. Align the brass dowels to the holes in the top. Starting
from one side install the 6mm L30 (Code D) machine screws. Gradually tighten the screws
until the top pulls tight against the front panels. Now tighten the 6 bolts (g) and the 6 nuts
and bolts from step 13.