Resource Kali Duo Board User manual

Kali Duo Board
Assembly
Instructions

WARNING
READ CAREFULLY BEFORE BEGINNING INSTALLATION.
IMPROPER INSTALLATION OF THE PRODUCT MAY CAUSE SERIOUS INJURY
Warranties for all products purchased from Resource Furniture, LLC are
only valid if the product has been properly assembled, Installed by a trained
professional, and operated in accordance with the assembly instructions.
Resource Furniture accepts no responsibility for any damage or injury caused
by Improper Installation.
Installation must be performed by a licensed contractor or a trained
professional, who will ensure proper assembly and installation.
Installation must be performed by at least 2 people.
Improper installation may result in permanent damage to the bed.
Improper installation of this product can cause serious or fatal injury.
No anchor can be used twice. If the product is removed from the wall, new
anchor holes must be drilled and new hardware must be used.
All hardware must be properly tightened. No parts of the model should be
left loose or unstable.
The wall bed must be secured to the wall in four locations using appropriate
hardware. The contractor or installer must select the proper anchoring hardware.
• The wall anchors included are for solid concrete walls only.
• Walls with wooden studs: Wood screws must be screwed into wooden studs in
the wall.
• Any other wall composition: A proper wall anchor suitable for the wall’s
construction must be selected by the contractor or installer.

KALI DUO BOARD MATTRESS SPECIFICATIONS
Recommended weight: ~ 3135 lbs
Recommended dimensions: W 31 1/2” X D 77 1/2” X H 7” 1
KALI DUO BOARD OVERVIEW
76 1/2"
194.3cm
OR
Model Shown
at 86 5/8" 220cm
76 1/2"
194.3cm
OR
Model Shown
at 86 5/8" 220cm

10
V
12
5
15
13
2
6
18
V
H
D
D
I
L
A
B
C
7
14
11
9
8
1
4
3
2
KALI DUO BOARD OVERVIEW

3
KALI DUO BOARD COMPONENTS
CODE QTY. COMPONENTS
1 1 Right side panel
2 1 Left side panel
3 1 Top horizontal panel
4 1 Bottom horizontal panel
5 1 Lower bed frame
6 1 Upper bed frame
7 2 Back panels
8 1 Upper back panel (IN only)
9 1 Structural shelf (IN only)
10 1 Upper storage cabinet door (IN only)
11 2 Metal bars for mattresses
12 2 Headboards
15 1 Ladder
16 1 Left (long) padded barrier
17 1 Right (short) padded barrier
18 1 Desk Brackets
19 1 Desk

4
KALI DUO BOARD WALL MOUNTING HARDWARE
CODE QTY. DESCRIPTION
WA 3
Wall anchors supplied
anchors are for solid
concrete walls only
WB 4 Wall brackets
WC 18 Bracket screws
KALI DUO BOARD TOOLS
QTY. DESCRIPTION
1 Allen wrench 4 MM
1 Allen wrench 6 MM
Note: The installer must determine the composition of the wall and appropriate anchors
prior to installation. The wall anchors included are for solid concrete walls only.

5
KALI DUO BOARD STRUCTURAL HARDWARE
CODE QTY. DESCRIPTION
A 12 Connector bolts
B 12 Cam connectors
C44 Phillips screw
D 8 Hex screws - for attaching
bed frame to structure
E 4 Flanged screws - for attaching
desk to desk mechanism
F 2
Conical Washers - for
attaching desk mechanism to
side panels
G 2
Flanged screws - for attaching
desk mechanism to vertical
side panels
H 4 Bolt - for attaching desk
I 4 Nut - for attaching desk
L 2 Screw - for attaching desk
V 2 For IN upper storage cabinet

6
1
STRUCTURE ASSEMBLY
Screw 8 A pins into the 1 right vertical and 2 left vertical panels. Attach the (4) horizontal bottom
panel ; (3) horizontal top panel and (9) structural shelf to the vertical panels by inserting and
tightening 12 (B) cams. Attach the 7 back panels to the structure with 22 C Phillips screws.

7
Wand Lighting
Installation Guideline for Kali Duo
Wand Light Exploded Diagram
Cord Length = 118”
Front
Back
• Drill 1/2” hole at 37 7/8” measured from the bottom of the structure (from inside) and 1
1/2” in from the side.
• Drill 1/2” hole at 69 1/8” measured from the bottom of the structure (from inside) and 1
1/2” in from the side.
2
OPTIONAL WAND LIGHTING
Drill 1/2” hole at 37 7/8” measured from the bottom of the structure (from inside) and 1 1/2” in
from the side. Drill 1/2” hole at 69 1/8” measured from the bottom of the structure (from inside)
and 1 1/2” in from the side.

8
3
WALL BED ATTACHMENT
1
2
3 4
1 2
3
4
1 2
3
4
1
2
3 4
After the unit is level and plumb it should be securely attached to the wall using the
metal angle mounting brackets as shown in the images below. A proper wall anchor
suitable for the wall’s construction must be selected by the contractor or installer.