Resource Tango 223 User manual

Assembly
Instructions
Tango 223 / 270

WARNING
READ CAREFULLY BEFORE BEGINNING INSTALLATION.
IMPROPER INSTALLATION OF THE PRODUCT MAY CAUSE SERIOUS INJURY
Warranties for all products purchased from Resource Furniture, LLC are
only valid if the product has been properly assembled, Installed by a trained
professional, and operated in accordance with the assembly instructions.
Resource Furniture accepts no responsibility for any damage or injury caused
by Improper Installation.
Installation must be performed by a licensed contractor or a trained
professional, who will ensure proper assembly and installation.
Installation must be performed by at least 2 people.
Improper installation may result in permanent damage to the bed.
Improper installation of this product can cause serious or fatal injury.
All hardware must be properly tightened. No parts of the model should be
left loose or unstable.

TANGO MATTRESS SPECIFICATIONS
Recommended weight: ~ 64 lbs
Recommended dimensions: 79 1/2 x 60 x 7” 1
TANGO OVERVIEW
Tango 223
Tango 270

2
TANGO OVERVIEW
FIXED SEAT MODEL

3
TANGO OVERVIEW
SLIDING/CHAISE SEAT MODEL

4
UPPER BOISERIE SHELVES
11a
11c
11b
11c
11b
Boiserie Panel Bottom Boiserie Shelves
(12 3/4”Depth)
Boiserie Box
A proper wall anchor suitable for the wall’s construction must be selected by
the contractor or installer.

TANGO COMPONENTS
CODE QT Y. COMPONENTS
1 1 Right side panel
2 1 Left side panel
3 1 Top horizontal panel
4 1 Base
5 2 Left/right small side panels (already attached to 1 & 2)
6 1 Right back panel
7 1 Left back panel
8 1 Bed frame
9 1 Mattress support bar
10 1 Shelf
11 1 Boiserie panel (optional)
12 1 Left arm bracket
13 1 Right arm bracket
14 1 Sofa base
15 1 Sofa base extension (Tango 270 version only)
16 1 Right sofa seat
17 1 Left sofa seat
18 1 Left armrest
19 1 Right armrest
20 1 Padded back bar
Modular sofa components may be included in place of left/right armrests, if ordered by the client.

6
TANGO FIXED SEAT STRUCTURAL HARDWARE
CODE QT Y. COMPONENT DESCRIPTION
A 13 7 x 36 6MA Pins
B 13 D15 L17 Cam Connectors
C 7 3.5 x 20 Wood screws for back
panels
D 4 5MA x 50 Screws for side panels
E 6 4MA x 18 Screws for mattress support
bar
F 4 4 x 40 Screws to attach top panel
G 4 8MA x 25 Screws for padded back bar
H 10 8MA x 35 Screws for sofa components
I 4 4 x 25 Screws for front shelf
J 4 8MA Nuts for sofa components
K 4 D9 x 24 Washers for sofa components
L 4 6MA x 20 Screws for fixed sofa seats

7
TANGO SLIDING SEAT STRUCTURAL HARDWARE
CODE QT Y. COMPONENT DESCRIPTION
A 13 7 x 36 6MA Pins
B 13 D15 L17 Cam Connectors
C 7 3.5 x 20 Wood screws for back
panels
D 4 5MA x 50 Screws for side panels
E 6 4MA x 18 Screws for mattress support
bar
F 4 4 x 40 Screws to attach top panel
G 4 8MA x 25 Screws for padded back bar
H18 8MA x 35 Screws for sofa components
I 4 4 x 25 Screws for front shelf
J 4 8MA Nuts for sofa components
K 4 D9 x 24 Washers for sofa components

8
TANGO TOOLS
BOISERIE PANEL TOOLS
QTY. DESCRIPTION
1 Allen wrench 3 MM
1 Allen wrench 4 MM
1 Allen wrench 5 MM
1 Allen wrench 8 MM
QTY. DESCRIPTION
M Metal shelf pins
N Boilts for shelf pins
O Boiserie bar
PWall anchors
Note: The installer must determine the composition of the wall and appropriate anchors
prior to installation. The wall anchors included are for solid concrete walls only.

9
1
2
STRUCTURE ASSEMBLY
These pieces
are pre-assembled.
A
B
A
Attach the (2) left side panel to the (4) base using 2 (D) screws.
Attach the 7 left back panel to the 2 left side panel using 3 A pins and 3 B cam connectors.
Attach the 6 right back panel to the 7 left back panel with 3 A pins and 3 B cam connectors.

STRUCTURE ASSEMBLY
B
A
F
These pieces
are pre-assembled.
c
c
c
c
c
c
c
3
4
Attach the (3) top horizontal panel to the (2) left side panel with 2 (A) pins and 2 (B) cam
connectors, and to the back panels with 4 (F) screws.
Attach the 1 right side panel to the 4 base using 2 D screws, and to the top horizontal
panel and back panels with 5 A pins and 5 B cam connectors. Secure the back panels to
the base using 7 C screws.
10

11
Wand Light Exploded Diagram
Cord Length = 118”
Front
Back
5
OPTIONAL WAND LIGHTING
Drill 1/2” hole at 21 3/8” measured downward from the inside of the top of structure and 1
1/2” in from the left and or right vertical side panel (on the inside). Install mounting plate
with provided wood screws.

12
LEVELING THE STRUCTURE
det.1
4a
6Ensure that the structure is level and plumb. To compensate for any floor unevenness,
use the adjustable feet on the bottom panel (det. 1 4a) to level the structure.

7
8
BED FRAME INSTALLATION
det.5a
det.6b
det.6a
Unscrew the safety plates fixed to the (4) structure base, as shown in det. 5a.
Position the (8) bed frame within the structure as shown. Place the levers located near the head
of the bed frame into their slots as shown in det. 6a, and re-attach the safety plates from Image
5. Ensure that pins on the bedframe slide into the base of the structure as shown in det. 6b.
Note: It is recommended to USE proper floor protection around the work area, under the bed
frame, so that the metal feet do not scratch the floor.
13

BED FRAME INSTALLATION
7
9
10
Attach the (9) mattress support bar to the bed frame using six (E) screws.
Lift the 8 bed frame into its upright vertical position. Screw the base pin to the lever
cords, leaving the screw on the outer side. Pass the cord under the pulleys on the base
4 and secure the pins on the appropriate seat.
14

FRONT SHELF INSTALLATION
11 Attach the shelf to the feet of the bedframe, as shown, using 4 (I) screws.
15
12
BED OPERATION
17
Installing the shelf
IMG.9: Attach the shelf to the feet of the bedframe, as shown, using 4 (I) screws.
OPENING THE BED
IMAGE 10:
Grasp the handle in the center of the shelf and pull down the bed, gently accompanying the
bed with both hands until it reaches the ground.
Grasp the handle in the center of the shelf and pull down the bed, gently accompanying
the bed with both hands until it reaches the ground.

16
BED AND HEADBOARD INSTALLATION
13 Attach the headboard (if purchased by client) to the back of the structure. Secure the mattress to
the bedframe by fastening the two buckled straps.

17
BED FRAME ADJUSTMENT
14 To balance the bedframe, adjust the spring tension controllers with the 8mm allen wrench
provided. Turn clockwise to adjust the tension in order to close the bed with ease. ensuring that
each side of the bedframe is adjusted equally.
Note: An excessive number of turns may damage the cable.

18
BOISERIE PANEL ASSEMBLY
15
16 17
Insert and fasten the (M) metal shelf pins into the holes on the (11A) boiserie panel using 2
(N) bolts each.
Place the boiserie panel next to the bed and
ensure panel is level and plumb. Attach the (O)
wall bracket to the wall using the (P) wall anchors
provided. Then, hang the (11A) boiserie panel on
the bracket.
Slide the boiserie shelves (11B) over
the (M) metal shelf pins.