RH Baby&child 175-15/16 User manual

COLETTE TUFTED CRIB
Page 1 of 14
TODDLER BED CONVERSION (SOLD SEPARATELY)
1. Read all instructions before assembly crib. Keep instructions for future use.
2. Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
3. Infants can suffocate in gaps between crib sides and a mattress that is too small.
Made in Vietnam
Model No: 175 - 15/16
Distributed in the U.S.A by:
RH Baby&Child
2900 N MACARTHUR DRIVE
TRACY, CA 95376
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia
V6E4N7
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Or call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools needed: Key Wrench (included).
Two people are recommended for assembly.
When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After bed is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool,
dry place and carefully package all original hardware to protect from loss.

Page 2 of 14
Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
Strangulation Hazard:
Strings can cause strangulation! DO NOT place items with a string around a child's neck, such as hood strings or
pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads, large
toys and other objects that could serve as steps for climbing out.
When child is able to climb out or reaches the height of 35 inches (89cm), the crib shall no longer be used, and
the child should be placed in a youth or regular bed.
Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly
and frequently during use. DO NOT use crib if any parts are missing, damaged or broken.
Contact customer service at 1-800-762-1751 for replacement parts and instructional literature if needed.
DO NOT substitute parts.
DO NOT use a water mattress with this crib.
If refinishing, use a non-toxic finish specified for children's products.
Follow warnings on all products in a crib.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
WARNING: Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions could result
in serious injury or death.
COLETTE TUFTED CRIB

Page 3 of 14
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4
INCHES BY 51 5/8 INCHES WITH A THICKNESS NOT EXCEEDING
6 INCHES.
WARNING:
Do not use this crib if the enclosed or attached instructions cannot
be strictly adhered to. Do not use this crib if the child is able to climb
out unaided or is taller than 35 inches (890mm). Do not place
cords, straps or similar items that could become wound around the
child's neck in or near this crib. Ensure that the sides are properly
latched or locked in place when the crib is occupied. The mattress
used with this crib should not be more than 5 7/8 inches (150mm)
thick and should be of such length and width that the gap between
the mattress and the sides of the crib is not more than 1 3/16 inches
(30mm) when the mattress is pushed into the corner of the crib.
Parents should inspect the crib regularly before putting the child
in the crib each day and confirm that every component of the crib
is properly and securely in place.
COLETTE TUFTED CRIB

Page 4 of 14
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
The mattress intended for use on the bed must be a full-size crib mattress
having minimum dimensions of 51 5/8 inches (1310mm) in length, 27 1/4
inches (690mm) in width and 4 inches (100mm) in thickness, not
exceeding 6 inches (152mm) in thickness.
If guardrails are used as the mattress containment means, guardrail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed that could cause an entrapment.
DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
DO NOT place items with a string, cord, or ribbon around a child's neck,
such as hood strings or pacifier cords.
A child using the toddler or day bed must be at least 15 months of age
and must not weigh more than 50 lbs (22.7kg).
WARNING: ENTRAPMENT/STRANGULATION HAZARD
COLETTE TUFTED CRIB

Page 5 of 14
PARTS INCLUDED:
A
B
C
D
HARDWARE INCLUDED:
[2]
[2]
[1]
[2]
HEADBOARD/FOOTBOARD
STATIONARY SIDE RAILS
MATTRESS SUPPORT
STRETCHER BARS
B
A
A
C
D
1
2
3
4
5
6
7
8 pcs.
4 pcs.
4 pcs.
16 pcs.
Hex Nut 6 x 10mm
Cap Hex Nut 6mm
16 pcs.
NO. ITEM DESCRIPTIONQTY.
8
9
4 pcs. Short Bolts 5/16” x 3/4”
4 pcs.
COLETTE TUFTED CRIB
Medium Bolts 5/16" x 50mm
Mattress Bolts 6 x 40mm
K.D. Barrel Nut
B
Long Bolts 5/16" x 80mm
Mattress Bolts 6 x 32mm
12 pcs.
Spring Washer 1/4" x 10 mm 4 pcs.

ASSEMBLY INSTRUCTIONS
Note:
- Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the above parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all steps are finished.
Page 6 of 14
NO. ITEM DESCRIPTIONQTY.
10
11
12
Allen Key 4mm 1 pc.
1 pc.
Hex Wrench 10mm
10mm
COLETTE TUFTED CRIB
STEP 1:
Attach the Stretcher Bars (D) to the
Headboard/Footboard (A). Insert
Barrel Nuts (3) into holes in Stretcher
Bars (D). Align threaded hole in barrel
nut with Long Bolt (4) and tighten with
Allen Key (11).
Note:
- Slot on barrel nut faces outward.
- Do not fully tighten at this time.
A
A
D
Flat Washer 1/4" x 16 mm 4 pcs.
4
11

Page 7 of 14
COLETTE TUFTED CRIB
STEP 2:
Note: The Mattress Support (C)
should be at the highest level
when the child is born.
It must be at the lowest level
before the child can stand up.
Before installing the Mattress
Support (C), determine the
desired height of the mattress.
C
Attach scissor assembly bars to
the Mattress Support (C) using
Mattress Bolts (7), Hex Nut (5)
and Cap Nut (6). Tighten with
Allen Key (11) and Hex Wrench (12).
Next, insert Mattress Bolts (7) into
the upper holes of the Mattress
Support (C) using Hex Nut (5) and
Cap Nut (6). Tighten with Allen
Key (1) and Hex Wrench (12).
11 7
512
6
Highest level
Lowest level
Middle level
5
11 7
6
12

Page 8 of 14
Attach the Mattress Support (C) to
the Stretcher Bars (D) using Mattress
Bolts (2), Spring Washer (9) Flat
Washer (10), Hex Nut (5), and Cap Hex
Nut (6). Tighten with Allen Key (11) and
Hex Wrench (12).
STEP 3:
D
C
2
11
12
9
10
5
6
COLETTE TUFTED CRIB
STEP 4:
Lay the Stationary Side Rails (B) in
between the Headboard/Footboard (A).
B
B

Page 9 of 14
WARNING:
After crib is completely
assembled, return to each bolt and
tighten to snug fit. DO NOT over
tighten.
B
A
1
11
STEP 5:
Attach the Stationary Side Rail (B)
to the Headboard/Footboard (A)
by using Medium Bolts (1) and
tighten with Allen Key (11).
COLETTE TUFTED CRIB
B
B

Page 10 of 14
PARTS INCLUDED:
E
[2] TODDLER RAIL
HARDWARE INCLUDED:
NO. ITEM DESCRIPTIONQTY.
4 pcs.
Allen Key 4mm 1 pc.
Short Bolts 5/16” x 3/4”
13
14
E
COLETTE TUFTED CRIB