RH Baby&child CALLUM User manual

CALLUM TWIN/ FULL PLATFORM CANOPY BED WITH HEADBOARD
Page 1 of 6
Note:
Two adults are recommended to assemble this bed.
Attach the Long Side Rails (D) to the
Short Side Rails (E).
PARTS INCLUDED:
A
B
C
D
E
F
G
H
TOOLS NEEDED:
Phillips-Head Screwdrive ( not included)
[1]
[2]
[2]
[2]
[2]
[1]
[2]
[2]
HEADBOARD PANEL
HEADBOARD POST
FOOTBOARD POST
LONG SIDE RAIL
SHORT SIDE RAIL
SLAT ROLL
LONG CANOPY RAILS
SHORT CANOPY RAILS
1
2
3
4
Long Bolt 5/16” x 2-1/4”
Spring Washer 5/16”
20 pcs.
Short Screws 8 x 15mm
Allen Key 4mm
Connecting Bolt 6mm
Camlock Wheel
Long Screw 8 x 30mm
5
6
7
8
9
20 pcs.
20 pcs.
4 pcs.
4 pcs.
4 pcs.
4 pcs.
1 pc.
Allen Key 5mm
10 1 pc.
20 pcs.
NO. ITEM DESCRIPTION QT Y.
STEP 1:
ASSEMBLY INSTRUCTIONS:
Flat Washer 5/16”
Assembling Insert
D
D
E
E

CALLUM TWIN/ FULL PLATFORM CANOPY BED WITH HEADBOARD
Page 2 of 6
STEP 2:
Attach the Short Side Rails (E) to
the Long Side Rail (D) using Short
Screws (5), and tighten with Philips
Head Screwdriver (not included).
STEP 3:
Place the hooks of the Headboard Panel (A)
into the slots in the Headboard Post (B).
If necessary, using a thick magazine or book
to protect the Headboard Panel (A), hammer
with a mallet or hammer until tight.
D
D
E
E
5
Phillips-head
screwdriver.

CALLUM TWIN/ FULL PLATFORM CANOPY BED WITH HEADBOARD
STEP 4:
Page 3 of 6
STEP 5:
Insert Flat Washer (2), Spring Washer (3),
and Long Bolt (1) and tighten with Allen
Key (6).
Attach the Headboard Posts (B) and
Footboard Posts (C) to the Bed Base.
Note:
- Bolts on Headboard/ Footboard are located
in the 1st and 3rd bolt locations.
- Bolts on the Side Rails are located in the 2nd
and 4th hole locations.
- Repeat steps for all 4 corners.
- Footboard Posts are interchangeable.
#1
#3
#2
#4
E
B&C
D
B
B
C
C
E
B&C
D

CALLUM TWIN/ FULL PLATFORM CANOPY BED WITH HEADBOARD
Page 4 of 6
STEP 7:
H
G
G
H
H
7
7
8
8
7
7
8
8
9
10
7
7
7
H
STEP 6:
Insert the Connecting Bolts (7) into
the Short Canopy Rails (H).
Secure the Short Canopy Rails (H) to the Long Canopy Rails (G).
Place Assembling Insert (8) into the holes inside of the Long
Canopy Rails (G) by aligning the hole of the Assembling Insert (8)
to the Connecting Bolt (7).
Then, insert the Camlock Wheel (9) into Assembling Insert (8) and
twist to tighten by counter clockwise direction using Allen Key (10).

CALLUM TWIN/ FULL PLATFORM CANOPY BED WITH HEADBOARD
STEP 8:
This final procedure should be done by 2 people working
together to carefully lift assembled canopy and place on
top of bed posts. Insert the Flat Washer (2), Spring
Washer (3), Long Bolt (1) into the holes of Short Canopy
Rails (H). Tighten with Allen Key (6). (See drawing below)
STEP 9:
Lay the Slat Roll (F) in between the
Long Side Rails (D), using Long
Screws (4) to tighten slats to the
side rails with a screwdriver.
1
3
2
6
Page 5 of 6
G
G
ASSEMBLY ALERT
• Make sure the canopy rails are put together
before place on top of the posts.
• Assembling the canopy: suggest to insert all
bolts before fully tighten all 4 corners.
4

CALLUM TWIN/ FULL PLATFORM CANOPY BED WITH HEADBOARD
CARE INSTRUCTIONS:
Dust often using a clean, soft, dry lint-free cloth.
Blot spills immediately, and wipe with a clean, damp cloth.
We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
STEP 10:
Assembly is completed.
Page 6 of 6