RH Baby&child Callum User manual

A S S E MBLY I N S TRUCTIONS :
S T EP 1 :
Attach the Right Storage Base (C)and
Left Side Rail (D) to the Headboard (A)
with Short Bolt (2),Spring Washer (3),
Flat Washer (4), and tighten by using
Allen Key (4).
S T EP 2 :
- Remove the drawer from Right Storage
Base (C) completely, and set it aside.
- Position the Footboard (B) between
the Right Storage Base (C) and Left Side
Rail (D) and align the holes.
Note:
- The drawer is equipped with rubber
stopper that prevent the drawer from
being removed during normal operation.
- During assembly, the drawer can be
removed with minor force as therubber
stoppers will bend to allow the drawer
to be removed completely.
- When removing the drawer, it MUST
be removed at a straight angle. If it is
crooked, the drawer will stick on the
wooden runners.
TOOLSN EEDED:
Phillips Head Screwdriver (not included)
PA R TS I N C LU D E D :
A[1]
B [1]
C [1]
D [1]
E [3]
F [2]
HEADBOARD PANEL
FOOTBOAR PANEL
RIGHT STORAGE BASE
LEFT SIDE RAIL
STRETCHER BARS
PLATFORM PANELS 2
3
4
5
Bolt5/16” x 1-3/4”4 pcs.
8 pcs.
8 pcs.
1pc.
Flat Washer 5/16”
624 pcs.
Screw 8 x 30mm
Spring Washer 5/16”
Allen Key 4mm
NO. ITEM DESCRIPTION QTY.
1Bolt5/16” x 2” 4 pcs.
D
4x
C
A
C
D
2
5
B
43
Page 1 of 3
CALL U M R IGHT S T ORAGE BED TWIN IN S TRUCTIONS

Page 2 of 3
4x
6x
1
5
6
Phillips Head Screwdriver (not included).
43
STEP 3:
Attach the Right Storage Base (C) and Left
Side Rail (D) to the Footboard (B) with Long
Bolt (1), Spring Washer (3), Flat Washer (4),
and tighten by using Allen Key (4).
STEP 4:
- Place the Stretcher Bars (E) on the opening
between the Right Storage Base (C) and Left
Side Rail (D). Tighten with Screws (6) and
Phillips Head Screwdriver (not included).
- Put the Drawer back into the Right Storage
Base (C) while bending the rubber stopper
as needed to allow the drawer to enter the
drawer box.
This will require some force to get the drawer
back into the box.
Note:
Make sure the wooden drawer runners, and the
rubber stoppers are properly aligned as you
re-install the drawer.
C
C
D
D
B
E
CALLUM RIGHT STORAGE BED TWIN INSTRUCTIONS

CARE INSTRUCTIONS:
1. Dust often using a clean, soft, dry lint-free cloth.
2. Blot spills immediately, and wipe with a clean, damp cloth.
3. We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
Page 3 of 3
STEP 5:
Lay the Platform Panels (F) on top of the
Stretcher Bars (E) and attach using Qty.18
Screws (6) with Phillip Head Screwdrive
18x 6
Phillips Head Screwdriver (not included).
F
F
CALLUM RIGHT STORAGE BED TWIN INSTRUCTIONS

ASSEMBLY INSTRUCTIONS:
STEP 1:
Attach the Left Storage Base (C) and
Right Side Rail (D) to the Headboard (A)
with Short Bolt (2),Spring Washer (3),
Flat Washer (4), and tighten by using
Allen Key (4).
STEP 2:
- Remove the drawer from Left Storage
Base (C) completely, and set it aside.
- Position the Footboard (B) between
the Left Storage Base (C) and Right
Side Rail (D) and align the holes.
Note:
- The drawer is equipped with rubber
stopper that prevent the drawer from
being removed during normal operation.
- During assembly, the drawer can be
removed with minor force as therubber
stoppers will bend to allow the drawer
to be removed completely.
- When removing the drawer, it MUST
be removed at a straight angle. If it is
crooked, the drawer will stick on the
wooden runners.
TOOLSNEEDED:
Phillips Head Screwdriver (not included)
PARTS INCLUDED:
A[1]
B [1]
C [1]
D [1]
E [3]
F [2]
HEADBOARD PANEL
FOOTBOAR PANEL
LEFT STORAGE BASE
RIGHT SIDE RAIL
STRETCHER BARS
PLATFORM PANELS 2
3
4
5
Bolt5/16” x 1-3/4”4 pcs.
8 pcs.
8 pcs.
1pc.
Flat Washer 5/16”
624 pcs.
Screw 8 x 30mm
Spring Washer 5/16”
Allen Key 4mm
NO. ITEM DESCRIPTION QTY.
1Bolt5/16” x 2” 4 pcs.
D
4x
C
C
D
2
5
A
B
4
3
Page 1 of 3
CALL U M L EFT S T ORAGE BED TWIN INSTRUC T I ONS

Page 2 of 3
4x
6x
1
5
6
Phillips Head Screwdriver
(not included).
4
3
STEP 3:
Attach the Left Storage Base (C) and Right
Side Rail (D) to the Footboard (B) with Long
Bolt (1), Spring Washer (3), Flat Washer (4),
and tighten by using Allen Key (4).
STEP 4:
- Place the Stretcher Bars (E) on the opening
between the Left Storage Base (C) and Right
Side Rail (D). Tighten with Screws (6) and
Phillips Head Screwdriver (not included).
- Put the Drawer back into the Left Storage
Base (C) while bending the rubber stopper
as needed to allow the drawer to enter the
drawer box.
This will require some force to get the
drawer back into the box.
Note: Make sure the wooden drawer runners,
and the rubber stoppers are properly aligned
as you re-install the drawer.
C
C
D
D
B
E
CALLUM LEFT STORAGE BED TWIN INSTRUCTIONS

CARE INSTRUCTIONS:
1. Dust often using a clean, soft, dry lint-free cloth.
2. Blot spills immediately, and wipe with a clean, damp cloth.
3. We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
Page 3 of 3
CALLUM LEFT STORAGE BED TWIN INSTRUCTIONS
18x
6
Phillips Head Screwdriver
(not included).
STEP 5:
Lay the Platform Panels (F) on top of the
Stretcher Bars (E) and attach using Qty.18
Screws (6) with Phillip Head Screwdrive
F
F