RH Baby&child AVALON STORAGE BUNK BED FULL OVER FULL User manual

WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above. Include the
product model number, color, and a brief description of the part.
Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth. Blot spills immediately and wipe
with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen key (included)
Wrench (included)
Screwdriver (not included)
Note: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After bunks is completely assembled, return to each bolt and tighten. Use
wax or soap on all bolts to facilitate assembly.
A V A L O N S T O R A G E B U N K B E D F U L L O V E R F U L L - A S S E M B L Y I N S T R U C T I O N S
18
/

IMPORTANT SAFETY INFORMATION FOR BUNK BED
1. Follow the information on the WARNINGS appearing on the upper bunk end
structure and on the carton.
2. Always use the specified size mattress, mattress support, or both to help
prevent the likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of
guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other
components are in their proper position, free from
damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement
parts.
10.Use of a night light may provide added safety precaution for a child using
the upper bunk.
11.Use guardrails on both sides of the upper bunk.
12.If the bunk bed will be placed next to a wall, the guardrail that runs the full
length of the bed should be placed against the wall to prevent entrapment
between the bed and the wall.
13. The use of water flotation mattress is prohibited.
14.STRANGULATION HAZARD - Never attach or hang items to any part of the
bunk bed that are not designed for use with the bed: for example, but not
limited to, hooks, belts, and jump ropes
15.Keep these instructions for future reference.
16.DO NOT remove warning label from bed.
A V A L O N S T O R A G E B U N K B E D F U L L O V E R F U L L - A S S E M B L Y I N S T R U C T I O N S
28
/

PARTS INCLUDED
A [1] HEADBOARD
B [1] FOOTBOARD
C [1] STORAGE
D [1] LOWER SIDE RAIL
E [2] UPPER SIDE RAILS
F1 [5] BED SLATS (LONG)
F2 [3] BED SLATS (SHORT)
G [1] LOWER PLATFORM PANEL
H [2] UPPER PLATFORM PANELS
I [1] LADDER
J [1] GUARD RAIL
A
B
C
D
E
F1
I
F2
G
H
H
COMPONENT IDENTIFICATION AND HARDWARE
NO. ITEM DESCRIPTION QTY.
1Threaded Rod 12 pcs.
2Curved Washer 12 pcs.
3Lock Washer 12 pcs.
4
5Wrench 1 pc.
Hex Nut 12 pcs.
Flat Head Phillips Screw
(M4 x 20mm) 12 pcs.
Allen Bolt 12 pcs.
Round Head Screw
(M4 x 25mm) 52 pcs.
Plain Washer 12 pcs.
Allen Key 1 pc.
NO. ITEM DESCRIPTION QTY.
6
7
8
9
Lock Washer 12 pcs.
NO. ITEM DESCRIPTION QTY.
10
NO. ITEM DESCRIPTION QTY.
11
Phillips Screwdriver
(Not provided) 1 pc.
13
NO. ITEM DESCRIPTION QTY.
TOOLS REQUIRED (NOT PROVIDED)
Metal Bracket 1 pc.
12
J
A V A L O N S T O R A G E B U N K B E D F U L L O V E R F U L L - A S S E M B L Y I N S T R U C T I O N S
38
/

ASSEMBLY INSTRUCTIONS
1. Lay the headboard (A) and footboard (B) on a flat surface.
2. Attach the Guard rail (J) to the footboard (B). Refer to FIGURE 1 & 2.
3. Attach the threaded rods (1) into the fixed nuts in the post of the headboard/footboard by turning them manually. See FIGURE 3 and FIGURE 4.
NOTE: The Guard rail can be installed at either end of the Headboard or Footboard depending on your desired ladder location. When Guard raill
(J) install into the left of the Footboard, refer to option A & B. In the opposite way, the guard rail will install into the right of the Footboard, refer to
option C & D.
IMPORTANT
These bed parts can be cumbersome and heavy, therefore the assistance of two or more people is recommended in order to prevent personal injury
and ensure the bed parts are not damaged during the assembly process.
OPTION A OPTION B
OPTION C OPTION D
Fig.4
Fig.4
1
1
11
11
FIGURE 1
FIGURE 2
FIGURE 3 FIGURE 4
A V A L O N S T O R A G E B U N K B E D F U L L O V E R F U L L - A S S E M B L Y I N S T R U C T I O N S
48
/

4. Fully remove all the drawers out of the storage (C). Attach the storage to the headboard (A), as per illustration in FIGURE 5, FIGURE 6 and
FIGURE 7.
5. Attach the lower side rail (D) to the headboard as per illustration in FIGURE 8. NOTE: Side panel is exchangeable for ladder placement on
either side.
6. Bring the upper side rail (E) in upright position and align the threaded rods on the headboard to the corresponding holes in the end of the
upper side rail. Attach the upper side rail to the headboard, as in FIGURE 9. KEEP HOLDING THIS SIDE RAIL DURING NEXT STEP.
7. Repeat step 6 to attach the other upper side rail to the headboard. KEEP HOLDING BOTH UPPER SIDE RAILS DURING NEXT STEP.
FIGURE 5
FIGURE 6
FIGURE 7
FIGURE 8
FIGURE 9
2
3
4
5
1
6
7
8
9
6
7
8
9
2
3
4
5
1
2
3
4
5
6
7
8
9
A V A L O N S T O R A G E B U N K B E D F U L L O V E R F U L L - A S S E M B L Y I N S T R U C T I O N S
58
/

8. Align the threaded rods on the footboard (B) to the corresponding
holes at the end of the storage (C), lower side rail (D) and upper
side rails (E). Align the locator pins on the end of the storage and
the side rails to the corresponding holes in the footboard. Insert the
footboard into the storage and the side rails.
9. Repeat step 3, 4, 5 and 6 to attach the storage and the side rails to
the footboard.
B
C
D
E
A
10. Set the bed slats (F1, F2) on the upper bunk and lower bunk. Secure each slat by using screws (10) provided. See FIGURE 10.
E
F1
Fig.10
FIGURE 10
10
F2
A V A L O N S T O R A G E B U N K B E D F U L L O V E R F U L L - A S S E M B L Y I N S T R U C T I O N S
68
/

11. Place the platform panels (G, H) on the lower bunk and the upper bunk, then fix them with screws (10). See FIGURE 11.
12. Hook the ladder (I) on the footboard then secure it with screws (11), as per illustration in FIGURE 12 and FIGURE 13.
13. Return the drawers to the storage. Assembly is complete.
G
H
H
Fig.11
FIGURE 11
10
Fig. 12
Fig. 13
11
FIGURE 12
no screw
FIGURE 13
11
A V A L O N S T O R A G E B U N K B E D F U L L O V E R F U L L - A S S E M B L Y I N S T R U C T I O N S
78
/

14. INSTALL BEDDING
BEDDING SPECIFICATION:
The following size mattress and foundation are specified for use with this bunk bed.
Mattress: 53''W x 75''L x 7''H on Full upper bunk, and 53''W x 75''L x 10''H on Full lower bunk.
**Note: TOP MATTRESS AND PLATFORM MUST NOT EXCEED 7'' TOTAL THICKNESS
Be sure to adhere to these BEDDING SPECIFICATIONS in order to avoid the possibility of falling or entrapment.
THESE SPECIFICATIONS MUST BE STRICTLY ADHERED TO!
UPPER BUNK MATTRESS DIAGRAM
[5''] MINIMUM DISTANCE
FROM TOP OF MATTRESS
TO TOP OF GUARDRAIL
[7'']
MAXIMUM
THICKNESS
PLATFORM PANEL SLAT SUPPORT
SIDE RAIL
GUARD RAIL
A V A L O N S T O R A G E B U N K B E D F U L L O V E R F U L L - A S S E M B L Y I N S T R U C T I O N S
88
/