RH Baby&child WILKES CONVERSION CRIB User manual

WILKES CONVERSION CRIB INSTRUCTIONS
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above. Include
the product model number, color, and a brief description of the part. Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth.
Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully package all original
hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After crib is completely assembled, return to each bolt and
tighten. Use wax or soap on all bolts to facilitate assembly
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
Page 1 of 10
All Restoration Hardware cribs are designed to meet the highest safety
standards and comply with all U.S. and Canadian cribs and cradles regulations.
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
2900 North Macarthur Dr. Tracy,
CA95376, USA
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7

Page 2 of 10
IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions
could result in serious injury or death.
·To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on their backs to
sleep, unless otherwise approved by your physician.
Strangulation Hazard:
·Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over over a crib or attach strings to toys.
·To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
·DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
·When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
·When child is able to climb out or reaches the height of 35 in (89 cm), the crib shall no longer be
used, and the child should be placed in a youth or regular bed.
·Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. DO NOT use crib if any parts are missing, damaged or
broken. Contact customer service at 1-800-762-1751 for replacement parts and instructional
literature if needed.
·DO NOT substitute parts.
·DO NOT use a water mattress with this crib.
·If refinishing, use a non-toxic finish specified for children’s products.
·Follow warnings on all products in a crib.
·Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
·Infants can suffocate in gaps between crib sides and a mattress that is too small.

Page 3 of 10
IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT
LEAST 27-1/4 INCHES BY 51-5/8 INCHES WITH A
THICKNESS NOT EXCEEDING 6 INCHES.
WARNING
Do not use this crib if you cannot exactly follow the instructions
that come with it.
Do not use this crib for a child who can climb out of it or who is
taller than 90 cm.
Do not place any cord, strap or similar item in or near this crib
that could become wrapped around a child's neck.
Do not place this crib near a window or patio door where a child
could reach the cord of a blind or curtain and be strangled.
Check this crib regularly before using it, and do not use it if any
part is loose or missing or if there are any signs of damage. Do
not substitute parts. Contact the manufacturer if replacement
parts or additions instructions are needed.
Children can suffocate on soft bedding. Do not place pillows,
comforters or soft mattresses in this crib.
Use a mattress that is no thicker than 15 cm and is of such a size
that, when it is pushed firmly against any side of this crib, it does
not leave a gap of more than 3 cm between the mattress and any
part of any other side of the crib.

Page 4 of 10
IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
·The mattress intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51-5/8 inches (1310mm) in
length, 27-1/4 inches (690mm) in width and 4 inches (100 mm) in
thickness, not exceeding 6 inches (152 mm) in thickness.
·If guardrails are used as the mattress containment means,
guardrail(s) provided must be used to avoid the formation of a gap
between the mattress and the bed that could cause an entrapment.
·DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or day bed shall be at least 15 months of age
and shall not weigh more than 50lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.

Page 5 of 10
Step #1 Side frame and headboard assembly (Page 6 of 10).
Step #2 Mattress support and stabilizer rail assembly.
Mattress height adjustment (Page 7 of 10).
Step #3 Support slat & side rail panel assembly (Page 8 of 10).
Step #4 Front panel assembly (Page 9 of 10).
Step #5 Toddler rail assembly (Page 10 of 10).
ITEM IDENTIFICATION
For ease of identification, all parts are labeled to correspond to the step number in which
the part is used.
SIDE RAIL PANEL
HEADBOARD
MATTRESS SUPPORT
FRONT RAIL

Page 6 of 10
STEP #1
HEAD BOARD & SIDE RAIL PANEL ASSEMBLY
STEP# 1.1
Bring the headboard and the side panel in upright
position.
NOTE:
On both side ends of the headboard are holes for the
bolt to pass through that correspond to the holes
located on both side ends of the side rail panel with
pre-installed nuts.
STEP#1.2:
Insert the bolt in each hole and tighten with Allen
wrench (provided). See DETAIL A.
HARDWARE NEEDED FOR STEP #1:
ALLEN WRENCH = 1 PC
(AA) 1/4" X 2-1/2" BOLT = 4 PCS
LOCK WASHER = 4 PCS
PLAIN WASHER = 4 PCS
(AA)
DETAIL A

Page 7 of 10
LOCK
WASHER
B
C
STEP #2
MATTRESS SUPPORT ARM ASSEMBLY
STABILIZER RAIL ASSEMBLY
MATTRESS HEIGHT ADJUSTMENT
DETAIL B
DETAIL C
HEX NUT
PLAIN
WASHER
ALLEN BOLT
(BB)
ALLEN
WRENCH
ALLEN WRENCH
OPEN WRECH
HEX NUT
LOCK WASHER
PLAIN WASHER
MATTRESS
SUPPORT
STABILIZER RAIL
HARDWARE NEEDED FOR STEP #2:
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
(BB) 1/4" X 1-3/8" BOLT = 8 PCS
LOCK WASHER = 8 PCS
PLAIN WASHER = 8 PCS
HEX NUT = 8 PCS
11 X 70
OPEN WRENCH = 1 PC
ALLEN WRENCH = 1 PC
STEP #2.1
Lay mattress support flat with stabilizer rail on each side.
NOTE:
On each end of the arm of the mattress support, there is a hole for the
bolt to pass through that corresponds to the holes located in the frame of
the mattress support.
STEP #2.2:
Insert the bolt into the desired hole of the frame through the hole on the
arm support. Fasten the bolt with plain washer, lock washers &
hexagonal nut provided. Repeat procedure on other arms of the
mattress support. See DETAIL B.
WARNING:
Set the mattress support to the desired height by adjusting the support
arms. The mattress support should be at its highest setting for
newborns, then adjusted to the lower positions as the child grows and
becomes mobile. Once the child is able to stand, the mattress support
should be at its lowest position.
STEP #2.3:
Install the stabilizer rail at ends of the arm support, as illustrated in
DETAIL C.

Page 8 of 10
STEP #3
SUPPORT SLAT INTO SIDE RAIL PANEL
ASSEMBLY DETAIL D
DETAIL F
DETAIL E
HARDWARE NEEDED FOR STEP #3:
STEP #3.1
On inside face of both side panels are pre-installed metal
brackets, designed to hold the stabilizer rails. Set both ends
of the stabilizer rails into brackets, as illustrated in DETAIL D.
STEP #3.2
Once the stabilizer rails are set, gently tilt the crib as
illustrated in DETAIL E, then fasten the stabilizer rails with
bolt together with plain washer and lock washer provided, as
illustrated in DETAIL F.
(CC) 1/4" X 13/16 " BOLT = 4 PCS
LOCK WASHER = 8 PCS
PLAIN WASHER = 8 PCS
ALLEN WRENCH = 1 PC
(CC)

Page 9 of 10
STEP #4
FRONT RAIL ASSEMBLY
STEP #4.1:
On both ends of the front rail are holes for the bolt to pass through and pre-installed wooden dowels that correspond
to the holes on the posts for both side rail panels with pre-installed nuts and pre-bored holes for the wooden dowels.
Align and insert the wooden dowel on the lower front rail into the lower holes of both side rail panels, then engage
the top bolt in each hole and tighten with Allen wrench provided, as in DETAIL G & DETAIL H.
After assembly, re-tighten all bolts to a snug fit. DO NOT OVER TIGHTEN.
HARDWARE NEEDED FOR STEP #4:
(DD) 1/4" X 1-3/4" BOLT = 4 PCS
ALLEN WRENCH = 1 PC
PLAIN WASHER = 4 PCS
LOCK WASHER = 4 PCS
H
H
H
H
G
G
WOODEN
DOWEL
LOCATOR SLOT
DETAIL G
(DD)
DETAIL H

Page 10 of 10
STEP #5
TODDLER RAIL ASSEMBLY
HARDWARE FOR STEP #5:
(PACKED INSIDE TODDLER RAIL BOX)
STEP #5.1:
Remove the front rail panel of the crib by loosening all the bolts
installed.
STEP #5.2:
Gently tilt the crib and release the bolts underneath the metal
brackets holding the stabilizer rails.
STEP #5.3
Gently remove the mattress support and slightly loosen the bolt
at the back of the headboard that enough to set the toddler rail
in-between side rail panel.
STEP #5.4
On inside face of both side rail panels there is a cavity for the
hook and a pre-installed nut for the Allen bolt to pass through,
which corresponds to the hooks on both ends of the toddler rail
and hole with holes pre-drilled. Align and insert the hook of the
toddler rail into the cavity of the side rail panel, then engage
Allen head bolt (removed from step #5.1) in the hole and tighten
with Allen wrench provided. See DETAIL I.
-NOTE: If mattress support is not in the lowest position, unscrew
mattress support bolts and move the lowest position.
STEP #5.5
Repeat step #2. Installation of stabilizer rails into the side panel
(DETAIL J).
After assembly, re-tighten all bolts to a snug fit.
STEP #5.6
Fill the holes located on the top of the side rail panel by inserting
bolt (EE) provided (Packed inside Toddler rail box). (DETAIL K)
(EE) 1/4" X 1/2" BOLT = 2 PCS
ALLEN WRENCH = 1 PC
(CC)
DETAIL J
I
I
K
K
METAL
HOOK
DETAIL I (DD)
(EE)
DETAIL K