RH Baby&child MARCELINE TWIN OVER User manual

Page 1 of 10
MARCELINE TWIN OVER TWIN BUNK BED INSTRUCTIONS
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE
Distributed in the U.S.A by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, California 91752
rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada Inc.
1500-1055 West Georgia Street,
Vancouver, British Columbia V6E 4N7
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing
to the address above .Include the product model number, color, and a brief description of the part. Call
1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Clean with mild soap on soft rag.
Rinse and dry thoroughly. If the bunk bed is to be stored, store in a cool dry place and carefully package all original
hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Wrench (included).
Phillips screw driver (not included).
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of a turn. After crib is completely
assembled, return to each bolt and tighten.

Page 2 of 10
WARNING
IMPORTANT SAFETY INFORMATION FOR BUNK BED
1. Follow the information on the WARNINGS appearing on the upper bunk end structure and on the carton.
2. Always use the specified size mattress or mattress support, or both to help prevent the likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other components are in their proper position, free from damage, and that all
connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts.
10. Use of a night light may provide added safety precaution for a child using the upper bunk.
11. Use guardrails on both sides of the upper bunk.
12. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment
between the bed and the wall.
13. The use of water flotation mattress is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use with the bed: for example, but not
limited to, hooks, belts, and jump ropes
15. Keep these instructions for future reference.
DO NOT REMOVE THIS LABEL
To help prevent serious or fatal injuries from
entrapment of falls:
·Never allow a child under 6 years on upper bunk.
·Use only mattress which is 74"-75" long and
371/2"-381/2" wide on upper bunk.
·Ensure thickness of mattress and foundation
combined does not exceed 9.5" and mattress is at
least 5" below upper edge of guardrails.
·Use guardrails on both sides of upper bunk.
·Prohibit horseplay on or under bed(s).
·Prohibit more than one person on upper bunk.
·Use ladder for entering and leaving upper bunk.
·STRANGULATION HAZARD - Never attach or hang
items to any part of the bunk bed that are not
designed for use with the bed; for example, but not
limited to, hooks, bells, and jump ropes.

Page 3 of 10
COMPONENT IDENTIFICATIONS AND HARDWARE
A
A
B
B
C
K
G
E
E
F
D
D
H
I
J
J
F
F
COMPONENTS
A LOWER END PANELS
B LOWER SIDE RAIL
C SLAT ROLL
D UPPER END PANELS
E UPPER END RAILS
F SLAT SUPPORT
G GUARD RAIL (BACK)
H GUARD RAIL (FRONT)
I LADDER
J TWIN PANEL
K TRUNDLE (SOLD SEPARATELY)
QTY
2 PCS
2 PCS
1 SET
2 PCS
2 PCS
3 PCS
2 PCS
1 PC
1 PC
1 PC
1 PC
7 28 pcs.
NO. ITEM DESCRIPTION QTY.
1Threaded Rod 16 pcs.
2Curved Washer 16 pcs.
3Lock Washer 16 pcs.
4
5
Wrench 1 pc.
Hex Nut 16 pcs.
6
Metal Bracket 4 pcs.
Phillips Wood Screw 25mm 26 pcs.
26 pcs.
Phillips Wood Screw 30mm
Phillips Wood Screw 20mm
8
9
10
11
Steel Dowel 4 pcs.
Wooden Cap 4 pcs.

Page 4 of 10
FIGURE 01
STEP #1. LOWER BUNK BED ASSEMBLY
STEP #1.1
Place the lower end panels (A, taller set) upright in the
position you wish the bed to be in when fully assembled.
The lower end panel's hardware should be facing
inwards. Secure the threaded rod (1) to the fixed nut on
both end panels (A) by simply turning manually. Raise
the side rail (B) up and place the rod (1) to align with the
bore holes on the end of the side rails (B). Put the side
rails (B) up against the end panels (A) so the threaded
rods go through the bore holes. Insert curved washer
(2) and lock washer (3), then engage hex nuts (4) on
threaded rod (1) and tighten hex nuts (4) with open
wrench (10), as illustrated in FIGURE 01.
STEP #1.2
Repeat the above procedure
with the other side rail (B).
ASSEMBLY INSTRUCTIONS:
STEP #1. LOWER BUNK BED ASSEMBLY.
STEP #2. INSTALLATION OF LOWER BUNK BED SLAT ROLL.
STEP #3. UPPER BUNK BED ASSEMBLY.
STEP #4. SLAT SUPPORT INSTALLATION TO UPPER SIDE RAILS.
STEP #5. ATTACH TWIN PANELS TO SLATS SUPPORT AND SIDE RAILS .
STEP #6. INSTALLATION OF FRONT AND BACK GUARD RAILS TO UPPER BUNK BED.
STEP #7. BUNK BED ASSEMBLY.
STEP #8. LADDER ASSEMBLY.
STEP #9. METAL BRACKET INSTALLATION AND OPTIONAL TRUNDLE.
STEP #10. TWIN BED ASSEMBLY.
IMPORTANT
These bed parts can be cumbersome and heavy to some people, therefore the assistance of two or more people is recommended in order to prevent
personal injury and ensure the bed parts are not damaged during the assembly process.
2
3
4
10
1
A
A
B
B

Page 5 of 10
FIGURE 02
FIGURE 03
STEP #2. INSTALLATION OF LOWER BUNK
BED SLAT ROLL
STEP #2.1
On the ends of the slat roll (C) are pre-bored screw holes (5). Set the
slat roll into the cleats of the side rails (B) and secure the slats roll (C)
with Phillips screws (5) provided. Please see FIGURE 02.
STEP #3. UPPER BUNK BED ASSEMBLY
STEP #3.1
Place the upper bunk end panels (D, shorter set) in upright position.
The upper end panel hardware should be facing inwards Secure the
threaded rod (1) to the fixed nut in both end panels (D) by simply
turning it manually. Raise the side rail (E) up and place the rod (1) to
align with the bore holes on the end of the side rails (E). Put the side
rails (E) up against the end panels (D) so the threaded rods go
through the bore holes. Insert curved washer (2) and lock washer
(3), then engage hex nuts (4) on threaded rod (1) and tighten hex
nuts (4) with open wrench (10), as illustrated in FIGURE 03.
STEP #3.2
Repeat the above procedure with the other side rail (E).
5
C
1
2
3
4
10
D
D
E
E

Page 6 of 10
FIGURE 04
FIGURE 05
STEP #4. SLAT SUPPORT INSTALLATION TO
UPPER SIDE RAILS
STEP #4.1
On inside surface of the side rails (E) are cavities designed to hold the
slat supports (F). Attach the slat supports (F) to both side rails (E) and
secure with screws (6) provided. Please see FIGURE 04.
STEP #5. ATTACH TWIN PANELS TO
SLAT SUPPORTS AND SIDE RAILS
STEP #5.1
Lay the two twin panels (J) on top of assembled
upper bunk bed and secure these with screws (6)
provided as in FIGURE 05.
6
F
6
J
J

Page 7 of 10
FIGURE 06
FIGURE 06-A
FIGURE 06-B
OPTION 2
OPTION 1
STEP# 6. INSTALLATION OF FRONT AND
BACK GUARD RAILS TO UPPER BUNK BED.
STEP #6.1
On inside surface of both front and back guard rail (G, H) are
pre-installed metal brackets, designed to attached to the side
rails (E) of the upper bunk. Install the front and the back guard
rail (G, H) on the upper bank by screwing (7) the metal
brackets into the side rails (E) (refer FIGURE 06-A).
NOTE:
The front guard can be installed at either end of the bed that
you desire depending on your desired ladder location. Please
see ladder options in FIGURE 06-B.
G
H
7

Page 8 of 10
FIGURE 08-A
FIGURE 07 - B
FIGURE 07 - A
FIGURE 08
STEP #7. BUNK BED ASSEMBLY
STEP #7.1
On top surface of lower end panels (A) are holes for steel
dowels (9) that correspond to the holes in the leg of the
upper bed (D). Insert steel dowels (9) on top of lower end
panels (A) as in FIGURE 07-A.
STEP #7.2
Gently lift up the upper bunk then align and insert the steel
dowels (9) into the holes in the bottom of the legs of upper
bunk. Refer to FIGURE 07-B. FIGURE 07
FIGURE 08-B
STEP #8. LADDER ASSEMBLY
STEP #8.1
On inside surface of the ladder (I) are metal brackets
pre-installed with holes for the screws (7) to pass through. Hook
the metal brackets of the ladder into the upper side rail (E) as
well as the brackets on lower side rail (B); once the ladder (I) is
set, fasten the ladder (I) with screws (7) provided as in FIGURE
08-A and FIGURE 08-B.
9
7
7

Page 9 of 10
[5"] MINIMUM DISTANCE
FROM TOP OF MATTRESS
TO TOP OF GUARDRAIL
8" MAXIMUM
THICKNESS
SLAT SUPPORT
TWIN PANEL
SIDE RAIL
GUARD RAIL
STEP # 9. METAL BRACKET INSTALLATION
STEP # 9.1
After assembling the bunk bed, secure Guard Rails (H & I) to upper side
rails (E) with metal plates (8) provided as in FIGURE 9.
STEP # 9.2
After assembly slide the optional trundle(sold separately) (K) underneath
the bunk bed as in FIGURE 10.
UPPER BUNK MATTRESS DIAGRAM
BEDDING SPECIFICATIONS:
The following size mattress and foundation are specified for
use with this bunk bed.
MATTRESS : 37 1
2" to 38 1 2" W x 74" x to 75" L maximum 9" H.
SLAT ROLL OR PLATFORM : 2 1
2" H X 38 7 8" W.
**Note: TOP MATTRESS AND PLATFORM MUST NOT
EXCEED 91
2" TOTAL THICKNESS.
Be sure to adhere to these BEDDING SPECIFICATIONS in
order to avoid the possibility of falling or entrapment. THESE
SPECIFICATIONS MUST BE STRICTLY ADHERED TO!
FIGURE 09 FIGURE 10
7
8

Page 10 of 10
FIGURE 12
FIGURE 11
STEP #10. TWIN BED ASSEMBLY - TO ASSEMBLE
BUNK AS TWO TWIN BEDS
STEP #10.1
Repeat step #1 to step #5, lower bunk bed assembly and upper bunk bed
assembly.
Note: in order to set up as two identical twin beds, one Lower End Panel
(A) may be removed and exchanged with one Upper End Panel (D), so
each bed has a headboard (Lower End Panel-A) and foot board (Upper
End Panel-D). Please refer FIGURE 12.
STEP #10.2
Insert wooden caps on top of lower end panels (A) as in figure 11.
11