RH Teen KIERAN User manual

KIERAN BUNK BED
Page 1 of 16
Made in Vietnam
Model No: 0288 - 14/15
Distributed in the U.S.A by:
RH Baby&Child
2900 N MACARTHUR DRIVE
TRACY, CA 95376
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia
V6E4N7
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Or call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools needed: Key Wrench (included).
Two people are recommended for assembly.
When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After bed is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool,
dry place and carefully package all original hardware to protect from loss.

Page 2 of 16
IMPORTANT SAFETY INFORMATION FOR BUNK BED
-
1. Follow the information on the WARNINGS appearing on the upper bunk end structure and on the
carton. DO NOT REMOVE WARNING LABEL FROM BED.
2. Always use the specified size mattress or mattress support, or both to help prevent the likelihood of
entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts
10. Use of a night light may provide added safety precaution for a child using the upper bunk.
11. Use guardrails on both sides of the upper bunk.
12. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water flotation mattresses is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are
not designed for use with the bed: for example, but not limited to, hooks, belts, and jump ropes.
15. Keep these instructions for future reference.
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM
ENTRAPMENT OR FALLS
1. Never allow a child under 6 years on upper bunk.
2. - If bunk is Twin/Twin:
Use only mattress which is 75" long and 38" wide and 7" height on upper bunk,
and mattress which is 75" long and 38" wide and 10" height on lower bunk.
- If bunk is Full/Full:
Use only mattress which is 75" long and 53" wide and 7" height on upper bunk,
and mattress which is 75" long and 53" wide and 10" height on lower bunk.
3. Ensure thickness of mattress does not exceed 7"and mattress surface is at least
5 inches below upper edge of guardrails. Thickness for lower bunk is 10” high.
4. Use guardrails on both sides of upper bunk.
5. Prohibit horseplay on or under bed(s).
6. Prohibit more than one person on upper bunk.
7. Use ladder for entering and leaving upper bunk.
8. If the bunk bed will be placed next to a wall the guardrails that run the full length
of the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
STRANGULATION HAZARD
9. Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed, for example, but not limited to hooks, belts, and jump ropes.
DO NOT REMOVE THIS LABEL
WARNING
KIERAN BUNK BED

PARTS IDENTIFICATION
Page 3 of 16
(C) Left Post of Footboard
(x1 piece)
(D) Right Post of Footboard
(x1 piece)
(A) Left Post of Headboard
(x1 piece)
(I) Headboard Panel (x1 piece) (J) Long Guard Rail (x1 piece)
(L) Front Guard Rail (x1 piece)
(G) Long Stretcher Bars (x2 pieces)
(M) Support Bars (x4 pieces)
(H) Short Stretcher Bars (x2 pieces)
(N) Top Platform Panels (x2 pieces) (O) Slat Roll (x1 set) (P) Ladder (x1 piece)
(B) Right Post of Headboard
(x1 piece)
(E) Long Side Rails (x2 pieces) (F) Short Side Rails (x2 pieces)
(K) Short Guard Rails (x2 pieces)
KIERAN BUNK BED

Page 4 of 16
HARDWARE INCLUDED
TOOLS NEEDED
Phillips-head screwdriver (not included)
1
2
3
4
5
6
7
8
9
10
7 pieces
2 pieces
1 piece
4 pieces
Long Bolt 5/16"x 2-1/2"
18 pieces
18 pieces
18 pieces
52 pieces
1 piece
32 pieces
Long Screw 8 x 30mm
Short Screw 8 x 19mm
Plastic Plugs 42 x 42 x 10mm
Key Wrench 4mm
NO. ITEM DESCRIPTIONQTY.
Small Bolts 1/4" x 5/8"
Threaded Rod 5/16" x 2-1/2"
Curved Slotted Washer
5/16"x 30 x 15x 2mm
Hex Nut
5/16"x 12 x 12mm
12 mm Hex Wrench 12mm
KIERAN BUNK BED

ASSEMBLY INSTRUCTIONS
Note: - Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten bolts until all steps are finished.
Page 5 of 16
NOTE:
The bunk has total of 2 orientations. Ladder (P) can be attached to left or right of the bunk bed, depending on where you would
like the Ladder (P) to be positioned (use options below).
SHORT GUARD RAIL CAN BE CONVERT TO LEFT OR RIGHT OF THE BUNK:
L
Orientation 1 Orientation 2
Orientation 1 Orientation 2
L
L
L
P
P
KIERAN BUNK BED

Page 6 of 16
TO CONVERT THE SHORT GUARD RAIL, FOLLOW THESE BELOW STEPS:
- Remove the crossbar on the bottom of the Guard Rail (L), by unscrewing
the screws on metal bracket (as seen below).
- Convert the open end of frame Guard Rail (L) to the left or right.
- Re-attach the cross bars to the Guard Rail (L) by the original screws.
- Tighten the screws using Phillips-head screwdriver (not included).
L
L
KIERAN BUNK BED

Page 7 of 16
STEP 1:
Insert the Threaded Rods (4) into the
Left/Right Post of Footboard (C, D).
4
45mm
45mm
4
D
C
C
D
K
H
F
Lay the Short Guard Rail (K), Short Side
Rail (F) and Short Stretcher Bar (H) to the
Left/Right Posts of Footboard (C, D)
(as seen below).
STEP 2:
KIERAN BUNK BED

Attach the Short Side Rail (F) and Short Guard Rail (K)
to the Left/Right Posts of Footboard (C, D). Insert
Curved Slotted Washers (5), and Hex Nut (6), and
tighten with Hex Wrench (9).
Next, insert Long Bolts (3) and tighten with Allen Key (1).
Page 8 of 16
STEP 3:
STEP 4:
D
C
H
K
F
1
9
6
5
4
3
1
2
Attach the Short Side Rail (F) and Short Stretcher Bar (H)
to the Left/Right Posts of Footboard (C, D) using Small
Bolts (2) and tighten with Allen Key (1).
KIERAN BUNK BED

Page 9 of 16
STEP 5:
B
45mm
45mm
A
4
4
Insert the Threaded Rods (4) into the
Left/Right Post of Headboard (A, B).
Lay the Short Guard Rail (K), Headboard
Fanel (I) and Short Stretcher Bar (H) to
the Left/Right Posts of Headboard (A, B)
(as seen below).
STEP 6:
B
A
K
H
I
KIERAN BUNK BED

STEP 7:
Page 10 of 16
STEP 8:
2
Attach the Short Guard Rail (K), Headboard Fanel (I)
and Short Stretcher Bars (H) to the Left/Right Posts
of Headboard (A, B), using Small Bolts (2) and
tighten with Allen Key (1).
Next, insert Long Bolts (3) and tighten with Allen Key (1).
H
K
I
I
1
Insert Curved Slotted Washers (5), and Hex
Nut (6) to Threaded Rod (4), and tighten with
Hex Wrench (9).
K
9
6
5
4
3
1
KIERAN BUNK BED

Page 11 of 16
STEP 9:
Carefully turn the headboard upside down.
Insert Curved Slotted Washers (5), and Hex
Nut (6) to Threaded Rod (4), and tighten
with Hex Wrench (9).
Then, insert Plastic Plugs (10) into holes on
the Headboard Panel (I).
9
4
6
5
10
10
KIERAN BUNK BED

STEP 10:
Page 12 of 16
G
E
J
L
E
G
Lay the Long Guard Rail (J), Front Guard Rail (L),
Long Side Rails (E), and Long Stretcher Bars (G)
to the posts of the headboard/footboard
(as seen below).
KIERAN BUNK BED

STEP 11:
Page 13 of 16
G
E
G
E
2
1
3
1
9
5
4
6
Attach the Long Side Rails (E), and Long
Stretcher Bars (G) to the posts of the
headboard/footboard, using Small
Bolts (2) and tighten with Allen Key (1).
STEP 12:
Insert Curved Slotted Washers (5), and
Hex Nut (6) to Threaded Rod (4), and
tighten with Hex Wrench (9).
Then, attach the Long Guard Rail (J) and
Front Guard Rail (L) to the headboard/
footboard, using Long Bolts (3) and
tighten with Allen Key (1).
KIERAN BUNK BED

STEP 13:
STEP 14:
Page 14 of 16
Carefully turn the bunk bed upright.
Position the Ladder (P) in the opening between the
Front Guard Rail (L) and footboard or headboard.
Hook the Ladder (P) over the cross bar of Front
Guard Rail (L) and Long Side Rail (E).
Insert the 4 Short Screws (8), and tighten
with Phillips-head screwdriver (not included).
Lay the Support Bars (M) between the Long
Guard Rail (J) and Front Guard Rail (L), using
Screws (7) and tighten with Phillips-head
screwdriver (not included).
Phillips-head
screwdriver.
M
7
8
P
P
L
M
KIERAN BUNK BED

STEP 15:
Page 15 of 16
N
Lay the Top Platform Panels (N) on top of the
Support Bars (M) and attach using Qty.40 pcs
Long Screws (7) with Phillips-head screwdriver.
Lay the Slat Roll (O) in between the Long Side
Rails (F) and use Long Screws (8) to fasten four
end slats to side rails with Phillips-head screwdriver.
7 (x40 pcs.)
7 (x4 pcs.)
- The webbing on the slats
should be on the top side.
After the bunk bed is completely assembled,
return to each bolt and tighten to snug fit.
DO NOT over tighten.
WARNING:
Can be adjusted
by using levelers.
O
KIERAN BUNK BED

Page 16 of 16
STEP 6:
INSTALL BEDDING
UPPER BUNK MATTRESS DIAGRAM
MATTRESS
BEDDING SPECIFICATIONS FOR TOP BUNK:
The following size mattress and Foundation are specified for use with this Bunk Bed:
MATTRESS DIMENSION SPECIFICATIONS FOR TOP BUNK
Twin - over - twin bunk: 75" long x 38" wide x 7" thick
Full - over - full bunk: 75" long x 53" wide x 7" thick
MATTRESS DIMENSION SPECIFICATIONS FOR LOWER BUNK
Twin - over - twin bunk: 75" long x 38" wide x 10" thick
Full - over - full bunk: 75" long x 53" wide x 10" thick
PLATFORM :
-Twin - over - twin bunk: Upper bed consists of 2 pcs platform 37 3/4" long x 38 3/4" wide x 3/4" thick & bottom bed consists of
14 pcs slats 38 3/4" long x 2 1/2" wide x 3/4" thick.
-Full - over - full Bunk: Upper bed consists of 2 pcs platform 37 3/4" long x 53 7/8" wide x 3/4" thick & bottom bed consists of
14 pcs slats 53 7/8" long x 2 1/2" wide x 3/4" thick.
**Note: MATTRESS THICKNESS MUST NOT EXCEED MAX 7" FOR TOP BUNK.
Be sure to adhere to these BEDDING SPECIFICATIONS in order to avoid the possibility of falling or entrapment.
THESE SPECIFICATIONS MUST BE STRICTLY ADHERED TO !
5" MINIMUM DISTANCE
FROM TOP OF MATTRESS
TO TOP OF GUARD RAIL
7" MAXIMUM
THICKNESS
SIDE RAIL
PLATFORM
KIERAN BUNK BED
CARE INSTRUCTIONS
Dust often using a clean, soft, dry, lint-free cloth.
Blot spills immediately, and wipe with a clean, damp cloth.
Do not use chemical cleansers, abrasives or furniture polish on the lacquered finish.