Rice Lake Retail Series Use and care manual

Retail Series
Calibration Manual
PN 170120 Rev AJanuary 5, 2018

An ISO 9001 registered company
© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems®is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and
accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make
changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product
updates can be found on our website:
www.ricelake.com

Contents
© Rice Lake Weighing Systems ●All Rights Reserved i
Contents
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
1.0 Counter-Top Scales...................................................................................................................................... 1
1.1 RS-130/RS-160 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1.1 Set JP1 Jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1.2 Simulate No Power Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Astra. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 AC-4000 B/E . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.4 BC-4000 L2/E. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5 SR-2000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.6 Uni-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.7 Uni-5 and Uni-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.8 Uni-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.0 Hanging Scales............................................................................................................................................. 9
2.1 BC-4000L2H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2 Uni-3L2H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Uni-7 Hanging . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Uni-9 Hanging . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.0 Wrapping Systems..................................................................................................................................... 14
3.1 BC-4000L2i/Ei . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2 IP-EMZ/OMNI-4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3 IP-Ai . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4 Uni-7 RP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.5 Uni-9 RP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.6 WM-Nano. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.7 WM-4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.8 WM-Ai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Retail Series Calibration Manual
1 Visit our website www.RiceLake.com
1.0 Counter-Top Scales
1.1 RS-130/RS-160
Follow the steps below to complete the calibration process.
1. Turn on the scale while pressing until 6.3 displays.
2. Press and hold until SETUP displays.
3. Press to enter calibration mode. The WEIGHT display flashes CAL-1 and shows UNIT 1.
The WEIGHT display will not flash CAL-1 if jumper JP1 is in the disabled position. Section 1.1.1 on page 1 if the
WEIGHT display will not flash CAL-1.
4. Press to select the weight unit (default is kg) to beused for calibration. An arrow displays over theselected unit.
•Unit1-kg
•Unit2-lb
• Unit 3 - oz (not available in Canada)
5. Press to accept the weight unit. The WEIGHT display shows:
• 00.000 (kg)
• 000.00 (lb)
• 0000.0 (oz) (not available in Canada)
6. Press to shift and to modify the flashing digit.
Example:

Use a 30 lb standard weight to calibrate; press to shift the flashing digit to 000.00 and press to set
the digit to 030.00.
Full capacity weight is required for calibration.
7. Press and wait for the WEIGHT display to show 000000 and the UNIT PRICE $ display to show the internal
offset value.
8. Place selected weight from Step 6 on the platter. WEIGHT display shows the internal span value and UNIT PRICE $
display shows the internal offset value.
9. Wait for the span value to become stable, then press .
10. Wait for the WEIGHT display to flash good twice. Quickly remove the weight from the platter. After automatic restart,
calibration is finished.
11. Disable JP1 to maintain the NTEP approval. Section 1.1.1.
1.1.1 Set JP1 Jumper
Follow the steps below to set JP1 to the enable or disable position.
1. Remove platterand plastic in-use cover.
2. Remove lead-seal located in the center of the base.
3. Remove the four screws from the base of the scale.
4. Lift the cover away from the base toward the operator side.
CHANGE
ZERO
ZERO
Note
CLEAR
CHANGE
CLEAR
CLEAR
Note
CHANGE
CHANGE

Counter-Top Scales
© Rice Lake Weighing Systems ●All Rights Reserved 2
Open slowly, cables are attached.
Figure 1-1. Jumper JP1 Location
Follow the steps below to reassemble the scale.
1. Place the cover on top of the base, ensuring that the sealing pin is aligned with the sealing pin hole in the base.
2. Tighten the four screws into the base of the scale.
3. Replace the lead seal in the center of the base over the sealing pin.
4. Replace the platter and plastic in-use cover.
Figure 1-2. Sealing Pin
1.1.2 Simulate No Power Display
A dealer can use this function to show a user when the scales needs charging.
1. Turn on the scale while pressing until 6.3 shows in the WEIGHT display (approximately three seconds).
2. Press and hold until the WEIGHT display shows SETUP (approximately three seconds).
3. Press , weight display shows USUAL.
4. Press , WEIGHT display shows -0.00-, UNIT PRICE $ display shows -0.00-, TOTAL $ display shows Lo-.
Note
Enable Disable
JP1
Sealing Pin
CHANGE
ZERO

Retail Series Calibration Manual
3 Visit our website www.RiceLake.com
1.2 Astra
Follow the steps below to calibrate the Astra scale.
1. Turn the scale off.
2. Turn the scale on while pressing . Release after the second beep. C00 TEST displays.
3. Press followed by . C01 HARD TEST displays.
4. Press to enter the A/D menu (C01-01). C01-01 AD DATA displays.
5. Press to display the A/D counts. C01-01-00 xxxx xxxx (where xxxx are internal counts) displays.
6. With no weight on the platter, press to initialize the A/D values. C01-01-00 2000 0 displays.
The initial value should be 2000 ± 1.
7. Place 30 lb (15 kg if set as 15 x 0.005 kg) on the platter. C01-01-00 32009 30009 displays.
8. If the calibration value is not 30000 ± 2, press . C01-01-00 32000 30000 displays.
9. Save the calibration data by pressing the memory switch located behind the nylon screw next to the 9-pin serial
connector.
10. Remove the weights.
Figure 1-3. Memory Switch Location
11. Press twice to return to the Hardware Test menu (C01). C01 HARD TEST displays.
12. Turn off the power to exit the Test Mode.
Do not use the RESET key to exit from Test Mode.
1.3 AC-4000 B/E
Follow the steps below to calibrate the AC-4000 scale.
1. Turn the scale off.
2. Turn the scale on while holding down the 1key until it beeps twice. C00 TEST MODE displays.
3. Key in 1followed by the DOWN ARROW. C01 HARDWARE TEST displays.
4. Press the ENTER key to enter the A/D menu (C01-01). C01-01 SCALE CALIBRATION displays.
5. Press the ENTER key to display the A/D counts. C01-01-00 xxxx xxxx (where xxxx are internal counts) displays.
6. With no weight on the platter, press the ZERO key to initialize the A/D values. C01-01-00 20000 0 displays.
The initial value should be 20000 ± 1.
7. Place 30 lb (15 kg if set as 15 x 0.005 kg) on the platter. C01-01-00 80000 60000 displays.
1
1
ENTER
ENTER
ZERO
Note
TARE
Memory Switch
END
IMPORTANT
Note

Counter-Top Scales
© Rice Lake Weighing Systems ●All Rights Reserved 4
8. If the calibration value is not 80000 ± 2, press the TARE key. C01-01-00 80000 60000 displays.
9. Remove the weights.
10. Save the calibration data by pressing the memory switch located underneath the platter.
Figure 1-4. Memory Switch Location
11. Press the END key twice to return to the Hardware Test menu (C01). C01 HARDWARE TEST displays.
12. Turn off the power to exit the Test Mode.
Do not use the RESET key to exit from Test Mode.
1.4 BC-4000 L2/E
Follow the steps below to calibrate the BC-4000 scale.
1. Turn the scale off.
2. Turn the scale on while holding down the 1key until it beeps twice. C00 TEST MODE displays.
3. Enter a 1using the keypad and press the DOWN ARROW. C01 HARDWARE TEST displays.
4. Press the ENTER key to enter the A/D menu (C01-01). C01-01 SCALE CALIBRATION displays.
5. Press the ENTER key to display the A/D counts. C01-01-00 xxxx xxxx (where xxxx are internal counts) displays.
6. With no weight on the platter, press the ZERO key to initialize the A/D values. C01-01-00 20000 0 displays.
The initial value should be 20000 ± 1. C01-01-00 20000 0 displays.
7. Place 30 lb (15 kg if set as 15 x 0.005 kg) on the platter. C01-01-00 32000 32000 displays.
8. If calibration value is not 80000 ± 2, press the TARE key. C01-01-00 80000 60000 displays.
9. Remove the weights.
10. Save the calibration data by pressing the MEMORY SWITCH located on the left side of the scale near the power switch
behind the while nylon seal screw or under an Ishida sticker.
Figure 1-5. Memory Switch Location
11. Press the END key twice to return to the Hardware Test menu (C01). C01 HARDWARE TEST displays.
12. Turn off the power to exit the Test Mode.
Do not use the RESET key to exit from Test Mode.
Memory Button
PK 236
IMPORTANT
Note
IMPORTANT

Retail Series Calibration Manual
5 Visit our website www.RiceLake.com
1.5 SR-2000
Follow the steps below to calibrate the SR-2000 scale.
1. Press .
2. Enter 495344 and press .
3. Select from the list.
4. With no weights on the platter, press to initialize the calibration values.
The initial A/D value should be 20000 ± 1.
5. Place scale capacity weight on the platter.
6. If the span value is not 80000± 2, press .
7. Remove the weight.
8. Save the calibration data by pressing the Memory Switch located under the platter under a sealing screw.
Figure 1-6. Memory Switch Location
9. Press . Verify the weight readings in operation mode.
1.6 Uni-3
Follow the steps below to calibrate the Uni-3 scale.
1. Enter 4000, then press . < C00 ADJUST > displays.
2. Enter 495344 and press to access hidden menus. < C00 ADJUST > displays.
3. Enter 8, then press . C08 CALIBRATION displays.
4. Press to enter theA/D menu (C08-01). C08-01 CAPACITY displays.
5. Press . C08-02 RANGE displays.
6. Enter 0 or 1, then press to specify the accuracy of the scale.
a. 0: SINGLE (0-30 x 0.01 lb)
b. 1: MULTI (0-15x 0.005 LB, 15-30 x 0.01LB)
7. Enter 10, then press toenter Span Calibration. C08-10 displays.
8. With no weight on the platter, press to initialize the A/D values. C08-10 20000 0.000 displays.
Note

Counter-Top Scales
© Rice Lake Weighing Systems ●All Rights Reserved 6
The initial value should be 20000 ± 1.
9. Place scale capacity weight on the platter and press . C08-10 80000 30.00 displays.
10. Remove the weight. C08-10 20000 0.000 displays.
11. Save the calibration data by pressing the span button located on the left side of the scale behind the bottom hex
screw. A long beep will sound after spanbutton has been pressed.
Figure 1-7. Uni-3 SPAN Button Location
12. Press , then press to exit. C08 CALIBRATION displays.
13. Press twice to exit to the operation mode.
14. Verify the weight readings in operation mode.
1.7 Uni-5 and Uni-7
Follow the steps below to calibrate the Uni-5 and Uni-7 scale.
1. Press .
2. Enter 495344 and press to access hidden menus.
3. Press .
Figure 1-8.
4. Select CALIBRATION from the list.
5. To select Single Range or Multi Range:
Uni-5: Press SINGLE or MULTI as needed.
Uni-7: Enter 495344 and then press SINGLE or MULTI as needed.
6. With no weight on the platter, press to initialize the A/D values.
The initial value should be 20000 ± 1.
7. Place scale capacity weight on the platter and press .
Note
Hex Screw
Covering Span
Button
Mode
PLU
Note

Retail Series Calibration Manual
7 Visit our website www.RiceLake.com
The A/D value should be 80000 ± 2.
8. Remove the weight.
9. Save the calibration data by pressing the Memory Switch located underneath the platter.
Figure 1-9. Uni-5 and Uni-7 Memory Switch location
10. Press and press OK.
11. Verify the weight readings in operation mode.
1.8 Uni-9
Follow the steps below to calibrate the Uni-9 scale.
1. Press .
2. Press and enter 495344. Press the PLU key to access hidden menus.
3. Press .
Figure 1-10. Select Calibration
4. Select CALIBRATION from the list.
5. Press SINGLE or MULTI, to select the range needed.
6. With no weight on the platter, press to initialize the A/D values.
The initial value should be 20000 ± 1.
7. Place scale capacity weight on the platter and press .
Note
Note

Counter-Top Scales
© Rice Lake Weighing Systems ●All Rights Reserved 8
The A/D value should be 80000 ± 2.
8. Remove the weight.
9. Save the calibration data by pressing the Memory Switch located underneath the platter.
Figure 1-11. Uni-9 Memory Switch location
10. Press in the upper right corner.
Figure 1-12. Executing Scale Adjustment
11. Verify the weight readings in operation mode.
Note

Retail Series Calibration Manual
9 Visit our website www.RiceLake.com
2.0 Hanging Scales
2.1 BC-4000L2H
Follow the steps below to calibrate the BC-4000L2H scale.
1. Turn the scale off.
2. Turn the scale on while holding down the 1key until it beeps twice. C00 TEST MODE displays.
3. Enter a 1using the keypad and press the DOWN ARROW. C01 HARDWARE TEST displays.
4. Press the ENTER key to enter the A/D menu (C01-01). C01-01 SCALE CALIBRATION displays.
5. Press the ENTER key to display the A/D counts. C01-01-00 xxxx xxxx displays (where xxxx are internal counts).
6. With no weight on the platter, press the ZERO key to initialize the A/D values. C01-01-00 20000 0 displays.
The initial value should be 20000 ± 1.
7. Place 30 lb (if setas 15 x 0.005 kg, use 15 kg)on the platter. C01-01-00 80000 60000 displays.
8. If the calibration value is not 80000 ± 2, press the TARE key. C01-01-00 80000 60000 displays.
9. Remove the weights from the scale.
10. Save the calibration data by pressing the memory switch located behind the brass seal bolt.
Figure 2-1. Calibration Button Location
11. Press the END key twice to return to the Hardware Test menu (C01). C01 HARD TEST displays.
12. Turn off the power to exit the Test Mode.
Do not use the RESET key to exit from Test Mode.
2.2 Uni-3L2H
Follow the steps below to calibrate the Uni-3L2H scale.
1. Enter in 4000, then press . < C00 ADJUST > displays.
2. Enter 495344, then press to access hidden menus. < C00 ADJUST > displays.
3. Enter 8, then press . C08 CALIBRATION displays.
4. Press to enter the A/D menu (C08-01). C08-01 CAPACITY displays.
Note
Calibration Switch
Location
IMPORTANT

Hanging Scales
© Rice Lake Weighing Systems ●All Rights Reserved 10
5. Press the . C08-02 RANGE displays.
6. Enter 0or 1, then press to specify the accuracy of the scale.
a. 0: SINGLE (0-30 x 0.01 lb)
b. 1: MULTI (0-15x 0.005 LB, 15-30 x 0.01LB)
7. Enter 10, then press to enter Span Calibration. C08-10 displays.
8. With no weight on the platter, press to initialize the A/D values. C08-10 20000 0.000 displays.
The initial value should be 20000 ± 1.
9. Place scale capacity weight on the platter and press . C08-10 80000 30.00 displays.
10. Remove the weight. C08-10 20000 0.000 displays.
11. Savethe calibrationdataby pressingthe span buttonlocatedon the bottom of thescalebehind the bottomhexscrew.
A long beep will sound after span button has been pressed.
Figure 2-2. Uni-3 SPAN button location
12. Press and then to exit. C08 CALIBRATION displays.
13. Press twice to exit to the operation mode.
14. Verify the weight readings in operation mode.
2.3 Uni-7 Hanging
Follow the steps below to calibrate the Uni-7 hanging scale.
1. Press .
2. Enter 495344 and press to access hidden menus.
3. Press .
Figure 2-3.
Note
Hex Screw Covering
Memory Button
Mode
PLU

Retail Series Calibration Manual
11 Visit our website www.RiceLake.com
4. Select CALIBRATION from the list.
5. To select Single Range or Multi Range, enter 495344 and press SINGLE or MULTI as needed.
6. With no weight on the platter, press to initialize the A/D values.
The initial value should be 20000 ± 1.
7. Place scale capacity weight on the platter and press .
The A/D value should be 80000 ± 2.
8. Remove the weight.
9. Save the calibration data by pressing the Memory Switch located on top of the scale body near the mounting pole
bracket. Remove the outside screw to access the button.
Figure 2-4. Uni-7 Memory Switch location
10. Press in the upper right corner and press OK.
11. Verify the weight readings in operation mode.
Note
Note

Hanging Scales
© Rice Lake Weighing Systems ●All Rights Reserved 12
2.4 Uni-9 Hanging
Follow the steps below to calibrate the Uni-9 hanging scale.
1. Press .
2. Press and enter 495344 and press the PLU key to access hidden menus.
3. Press .
Figure 2-5. Select Calibration
4. Select CALIBRATION from the list.
5. Press SINGLE or MULTI, to select the range needed.
6. With no weight on the platter, press to initialize the A/D values.
The initial value should be 20000 ± 1.
7. Place scale capacity weight on the platter and press .
The A/D value should be 80000 ± 2.
8. Remove the weight.
9. Remove outside screw to access the Memory Switch located on top of the scale body near the mounting pole bracket.
10. Save the calibration data by pressing the Memory Switch.
Figure 2-6. Uni-9 Memory Switch location
Note
Note

Retail Series Calibration Manual
13 Visit our website www.RiceLake.com
11. Press the in the upper right corner.
Figure 2-7.
12. Verify the weight readings in operation mode.

Wrapping Systems
© Rice Lake Weighing Systems ●All Rights Reserved 14
3.0 Wrapping Systems
3.1 BC-4000L2i/Ei
Follow the steps below to calibrate the BC-4000 scale.
1. Turn the scale off.
2. Turn the scale on while holding down the 1key until it beeps twice. C00 TEST MODE displays.
3. Enter a 1using the keypad and press the DOWN ARROW. C01 HARDWARE TEST displays.
4. Press the ENTER key to enter the A/D menu (C01-01). C01-01 SCALE CALIBRATION displays.
5. Press the ENTER key to display the A/D counts. C01-01-00 xxxx xxxx (where xxxx are internal counts) displays.
6. With no weight on the platter, press the ZERO key to initialize the A/D values. C01-01-00 20000 0 displays.
The initial value should be 20000 ± 1.
7. Place 30 lb (15 kg if set as 15 x 0.005 kg) on the platter.
8. If calibration value is not 80000 ± 2, press the TARE key. C01-01-00 80000 60000 displays.
9. Remove the weights.
10. Save the calibration data by pressing the Memory Switch located on the left side of the main body of the scale. It is
under the small white nylon sealscrew or under an Ishida sticker.
Figure 3-1. Memory Switch location
11. Press the END key twice to return to the Hardware Test menu (C01). C01 HARD TEST displays .
12. Turn off the power to exit the Test Mode.
Do not use the RESET key to exit from Test Mode.
Note
IMPORTANT

Retail Series Calibration Manual
15 Visit our website www.RiceLake.com
3.2 IP-EMZ/OMNI-4000
Follow the steps below to calibrate the IP-EMZ scale and the OMNI-4000 auto wrapper.
1. Press .
Figure 3-2.
2. Enter 495344 and press .
3. Select from the list.
4. With no weight on the platter, press to initialize the A/D values.
The initial value should be 20000 ± 1.
5. Place scale capacity weight on the platter and press .
The A/D value should be 80000 ± 2.
6. Remove the weight.
7. Save the calibration data by pressing the Memory Switch.
IP-EMZ– locatedunderneaththeplatter,removethe smallplasticrectangularcoverand theseal boltand metalcover.
OMNI-4000 – located under the package infeed conveyor, remove the metal plate and then the round adhesive decal.
Figure 3-3. Memory Switch locations
8. Press .
9. Verify the weight readings in operation mode.
Note
Note
IP-EMZ OMNI-4000

Wrapping Systems
© Rice Lake Weighing Systems ●All Rights Reserved 16
3.3 IP-Ai
Follow these steps to calibrate the IP-Ai scale.
1. Press the key.
2. Enter 495344 and press the PLU key to access hidden menu steps.
3. Select .
Figure 3-4. Select Calibration
4. Select CALIBRATION from the list.
5. Press SINGLE or MULTI, to select the range needed.
6. With no weight on the platter, press to initialize the A/D values.
The initial value should be 20000 ± 1.
7. Place scale capacity weight on the platter and press .
The A/D value should be 80000 ± 2.
8. Remove the weight.
9. Save the calibration data by pressing the Memory Switch located underneath the platter, remove the small plastic
rectangular cover and the seal bolt and metal cover.
Figure 3-5. Memory Switch Location
Note
Note

Retail Series Calibration Manual
17 Visit our website www.RiceLake.com
10. Press the in the upper right corner.
Figure 3-6.
11. Verify the weight readings in operation mode.
3.4 Uni-7 RP
Follow the steps below to calibrate the Uni-7 RP scale.
1. Press .
2. Enter 495344 and press to access hidden menus.
3. Press .
Figure 3-7.
4. Select CALIBRATION from the list. The RP unit comes set as kg, it is necessary to switch to lb.
5. Enter 495344.
6. Press the CAPACITY field on the screen and edit the capacity to 30 lb.
7. To select Single Range or Multi Range, enter 495344 and then press SINGLE or MULTI as needed.
8. With no weight on the platter, press to initialize the A/D values.
The initial value should be 20000 ± 1.
9. Place scale capacity weight on the platter and press .
The A/D value should be 80000 ± 2.
10. Remove the weight.
11. Save the calibration data by pressing the Memory Switch locatedunderneaththeplatterinthescale base.Remove the
small plastic rectangular cover and the seal bolt and metal cover.
Mode
PLU
Note
Note