Ricoh Aficio MP 1600L User manual

Operating Instructions
Troubleshooting
Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the
Safety Information in "About This Machine" before using the machine.
When the Machine Does Not Operate As Wanted
Troubleshooting When Using the Copy Function
Troubleshooting When Using the Facsimile Function
Troubleshooting When Using the Printer Function
Troubleshooting When Using the Scanner Function
Adding Paper and Replacing Toner
Clearing Misfeeds
Remarks
1
2
3
4
5
6
7
8

Introduction
This manual contains detailed instructions and notes on the operation and use of this machine. For your
safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy
place for quick reference.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be li-
able for direct, indirect, special, incidental, or consequential damages as a result of handling or oper-
ating the machine.
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Depending on which country you are in, certain units may be optional. For details, please contact your
local dealer.
Caution:
Use of controls or adjustments or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Notes:
The model names of the machines do not appear in the following pages. Check the type of your ma-
chine before reading this manual. (For details, see “Machine Types”, About This Machine.)
• Type 1: MP 1600/Aficio MP 1600/IS 2316
• Type 2: MP 2000/Aficio MP 2000/IS 2320
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the metric version.
For good copy quality, the supplier recommends that you use genuine toner from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products.
Power Source
220 - 240V, 50/60Hz, 7A or more.
Please be sure to connect the power cord to a power source as shown above. For details about power
source, see p.95 “Power Connection”.

i
Manuals for This Machine
Refer to the manuals that are relevant to what you want to do with the machine.
Important
❒Media differ according to manual.
❒The printed and electronic versions of a manual have the same contents.
❒Adobe Acrobat Reader/Adobe Reader must be installed in order to view the
manuals as PDF files.
❒Depending on which country you are in, there may also be html manuals. To
view these manuals, a Web browser must be installed.
❖About This Machine
Be sure to read the Safety Information in this manual before using the machine.
This manual provides an introduction to the functions of the machine. It also
explains the control panel, preparation procedures for using the machine,
how to enter text, and how to install the CD-ROMs provided.
❖General Settings Guide
Explains User Tools settings, and Address Book procedures such as register-
ing fax numbers, e-mail addresses, and user codes. Also refer to this manual
for explanations on how to connect the machine.
❖Troubleshooting
Provides a guide to solving common problems, and explains how to replace
paper, toner, and other consumables.
❖Security Reference
This manual is for administrators of the machine. It explains security func-
tions that the administrators can use to protect data from being tampered
with, or prevent the machine from unauthorized use.
Also refer to this manual for the procedures for registering administrators, as
well as setting user and administrator authentication.
❖Copy Reference
Explains Copier functions and operations. Also refer to this manual for expla-
nations on how to place originals.
❖Facsimile Reference
Explains Facsimile functions and operations.
❖Printer Reference
Explains Printer functions and operations.
❖Scanner Reference
Explains Scanner functions and operations.

ii
❖Network Guide
Explains how to configure and operate the machine in a network environ-
ment, and use the software provided.
This manual covers all models, and includes descriptions of functions and
settings that might not be available on this machine. Images, illustrations, and
information about operating systems that are supported might also differ
slightly from those of this machine.
❖Other manuals
• Quick Reference Copy Guide
• Quick Reference Fax Guide
• Quick Reference Printer Guide
• Quick Reference Scanner Guide
• PostScript3 Supplement
•UNIXSupplement
• Manuals for DeskTopBinder Lite
• DeskTopBinder Lite Setup Guide
• DeskTopBinder Introduction Guide
•AutoDocumentLinkGuide
Note
❒Manuals provided are specific to machine types.
❒For “UNIX Supplement”, please visit our Web site or consult an authorized
dealer.
❒“PostScript3 Supplement” and “UNIX Supplement” include descriptions of
functions and settings that might not be available on this machine.

iii
TABLE OF CONTENTS
Manuals for This Machine ......................................................................................i
How to Read This Manual .....................................................................................1
Symbols .....................................................................................................................1
Names of Major Options ............................................................................................1
1. When the Machine Does Not Operate As Wanted
Indicators................................................................................................................3
Panel Tone..............................................................................................................4
When the Function Status Indicator Lights Up in Red.......................................5
When You Have Problems Operating the Machine.............................................6
When a Job Is Not Performed...............................................................................9
2. Troubleshooting When Using the Copy Function
When a Message Is Displayed............................................................................11
When You Cannot Make Clear Copies ...............................................................13
When You Cannot Make Copies As Wanted .....................................................15
When Memory Is Full ...............................................................................................17
3. Troubleshooting When Using the Facsimile Function
Adjusting the Volume ..........................................................................................19
When a Message Is Displayed............................................................................22
When You Cannot Send or Receive Fax Messages As Wanted ......................29
When Memory Is Full ...............................................................................................33
When an Error Report Is Printed ........................................................................34
Turning Off the Main Power / In the Event of Power Failure............................35
When an Error Occurs Using Internet Fax ........................................................36
Error Mail Notification...............................................................................................36
Error Report (E-Mail)................................................................................................36
Server-Generated Error E-mail ................................................................................36
4. Troubleshooting When Using the Printer Function
When a Message Is Displayed during Installation of the Printer Driver .........37
Windows 95/98/Me, Windows 2000 or Windows NT 4.0 .........................................37
Windows XP Professional or Windows Server 2003................................................37
Windows XP Home Edition ......................................................................................38
When a Message Is Displayed............................................................................39
Status Messages......................................................................................................39
Alert Messages ........................................................................................................39
Printing the Error Log ...............................................................................................41
When You Cannot Print.......................................................................................42
Other Printing Problems .....................................................................................45

iv
5. Troubleshooting When Using the Scanner Function
When Scanning Is Not Done As Expected ........................................................53
When You Cannot Send Scanned Files.............................................................54
When You Cannot Browse the Network to Send a Scanned File ............................54
When the TWAIN Driver Cannot Be Started ............................................................54
The Network Delivery Function Cannot Be Used.....................................................54
Operations Are Not Possible When Messages Appear ...........................................55
When a Message Is Displayed............................................................................56
When a Message Is Displayed on the Display Panel...............................................56
When a Message Is Displayed on the Client Computer...........................................60
6. Adding Paper and Replacing Toner
Loading Paper ......................................................................................................65
Loading Paper into the Paper Trays ........................................................................65
Loading Paper into the Optional Paper Tray Unit ....................................................67
Orientation-Fixed Paper or Two-Sided Paper ..........................................................68
Changing the Paper Size.....................................................................................71
Changing the Paper Size in the Paper Tray.............................................................71
Changing a Paper Size in the Optional Paper Tray Unit..........................................79
Adding Toner........................................................................................................84
Replacing Toner.......................................................................................................85
Sending Fax Messages When Toner Has Run Out .................................................86
Waste Toner.............................................................................................................86
Replacing the Transmission Stamp Cartridge ..................................................87
7. Clearing Misfeeds
Removing Jammed Paper ...................................................................................89
8. Remarks
Where to Put Your Machine ................................................................................93
Machine Environment ..............................................................................................93
Moving......................................................................................................................94
Power Connection....................................................................................................95
Access to the Machine .............................................................................................96
When Not Used for a Long Time..............................................................................96
Maintaining Your Machine ..................................................................................97
Cleaning the Exposure Glass...................................................................................97
Cleaning the Exposure Glass Cover ........................................................................98
Cleaning the ADF/ARDF ..........................................................................................98
INDEX......................................................................................................... 99

1
How to Read This Manual
Symbols
This manual uses the following symbols:
Indicates important safety notes.
Ignoring these notes could result in serious injury or death. Be sure to read these
notes. They can be found in the “Safety Information” section of About This Machine.
Indicates important safety notes.
Ignoring these notes could result in moderate or minor injury, or damage to the
machine or to property. Be sure to read these notes. They can be found in the
“Safety Information” section of About This Machine.
Indicates points to pay attention to when using the machine, and explanations
of likely causes of paper misfeeds, damage to originals, or loss of data. Be sure
to read these explanations.
Indicates supplementary explanations of the machine's functions, and instruc-
tions on resolving user errors.
This symbol is located at the end of sections. It indicates where you can find fur-
ther relevant information.
[]
Indicates the names of keys that appear on the machine's display panel.
{}
Indicates the names of keys on the machine's control panel.
Names of Major Options
Major options of this machine are referred to as follows in this manual:
• Auto Document Feeder →ADF
• Auto Document Feeder capable of scanning both sides of a sheet →ARDF

2

3
1. When the Machine Does
Not Operate As Wanted
This section describes basic troubleshooting procedures that are applicable to all
functions of this machine.
Indicators
This section explains the indicators that light up when the machine requires the
user to remove misfed paper, add paper, or perform other procedures.
h: Error indicator Appears when there is a misfeed, a cover is left open, or
another problem occurs. See p.89 “Clearing Misfeeds”.
B: Load Paper indicator Appears when paper-out condition occurs. See p.65
“Loading Paper”.
D: Add Toner indicator Appears when toner runs out. See p.84 “Adding Toner”.

When the Machine Does Not Operate As Wanted
4
1
Panel Tone
The following table explains the various beep patterns that the machine produc-
es to alert users about machine conditions.
Note
❒Users cannot mute the machine's beep alerts. When the machine beeps to alert
users of a paper jam or toner request, if the machine's covers are opened and
closed repeatedly within a short space of time, the beep alert might continue,
even after normal status has resumed.
Reference
For details about enabling or disabling beep alerts, see “General Features”,
General Settings Guide.
Beep pattern Meaning Cause
Two long beeps. Machine has warmed
up.
After cooling or being switched on, the
machine has fully warmed up and is
ready for use.
Single short beep. A valid operation is
accepted.
A control panel key was pressed, the
machine was switched on, or a docu-
ment was placed on the ADF or ARDF.
Five short beeps repeated
five times.
Strong alert. Machine requires user attention. Paper
might have jammed or toner might need
replenishing.

When the Function Status Indicator Lights Up in Red
5
1
When the Function Status Indicator Lights
Up in Red
If a function key is lit in red, press the key to switch to the screen for the corre-
sponding function, and then follow the message that appears.
Note
❒If an error occurs in the function you are using, check the message that ap-
pears on the display panel, and then refer to “When a Message Is Displayed”
for the relevant function.
Reference
p.11 “Troubleshooting When Using the Copy Function”
p.19 “Troubleshooting When Using the Facsimile Function”
p.37 “Troubleshooting When Using the Printer Function”
p.53 “Troubleshooting When Using the Scanner Function”
Problem Cause Solution
Documents and reports
are not printed out.
There is no copy paper left. Add more paper. See p.65 “Load-
ing Paper”.
An error has occurred. The function whose indicator is lit
is defective.
Record the code number shown
in the display and contact your
service representative. See
“When a Message Is Displayed”
of each chapter. You can use other
functions normally.
The machine is unable to
connect to the network.
A network error has occurred. • Check the displayed message
and take an appropriate ac-
tion. See “When a Message Is
Displayed” of each chapter.
• Check that the machine is cor-
rectly connected to the net-
work, and that the machine is
correctly set. See “Network
Settings”, General Settings
Guide.
• Contact the administrator.
• When the function key is still
lit in red, even if you take the
measures above, contact your
service representative.

When the Machine Does Not Operate As Wanted
6
1
When You Have Problems Operating the
Machine
The following chart gives explanations of common problems and messages.
If other messages appear, follow the instructions displayed.
Problem Cause Solution
“Please wait.”
appears.
This message appears when you
turn on the operation switch or
change the toner bottle.
If the machine does not get start-
ed within 2 minutes, contact your
service representative.
“Please wait.”
appears.
If the machine has not been in use
for a long time, it may take longer
than normal to print or start up
when switched on.
Wait for the machine to get ready.
Although the copier
screen appears when
the machine is turned
on using the main
power switch, it cannot
be switched to another
screen by pressing the
{Facsimile}or {Scan-
ner}key.
Functions other than the copier
function are not yet ready.
Wait a little longer.
The machine has just
been turned on and the
User Tools screen is
displayed, but the User
Tools menu has items
missing.
Functions other than the copier
function are not yet ready. Time
required varies by function.
Functions appear in the User
Tools menu when they become
ready for use.
Wait a little longer.
The display is difficult
to see.
Screen contrast is not adjusted. Adjust the screen's contrast so
that you can see the display panel
properly. See “General Features”,
General Settings Guide.
The display is off. The machine is in Energy Saver
mode.
Turn on the operation switch.
The display is off. The operation switch is turned
off.
Turn on the operation switch.
Nothing happens
when the operation
switch is turned on.
The main power switch is turned
off.
Turn on the main power switch.
The operation switch
indicator continues
blinking and does not
turn off when pressed.
The machine is communicating
with external equipment.
Check if the machine is communi-
cating with a computer.

When You Have Problems Operating the Machine
7
1
Original images are
printed on the reverse
side of the paper.
You may have loaded the paper
incorrectly.
Load paper correctly. Load paper
into Tray 1-4 with the print side
up, and into the bypass tray with
the print side down. See p.68
“Orientation-Fixed Paper or
Two-Sided Paper”.
Misfeeds occur frequently. The tray's side fences may not be
locked.
Check the side fences are locked.
See p.71 “Changing the Paper
Size”.
Misfeeds occur frequently. The tray's end fence may not be
set properly.
Check the end fence is set proper-
ly. See p.71 “Changing the Paper
Size”.
Misfeeds occur frequently. You may have loaded paper of a
size not shown on the paper size
selector.
Use Tray Paper Settings to set the
paper size. See p.78 “Changing to
a Size Other Than Indicated on
the Paper Size Selector”.
An error message re-
mains, even if misfed
paper is removed.
When a misfeed message ap-
pears, it remains until you open
and close the cover as required.
Paper is still jammed in the tray.
Clear misfed paper, and then
open and close the cover. See p.89
“Removing Jammed Paper”.
Cannot print in duplex
mode.
You cannot use paper in the by-
pass tray for duplex printing.
For duplex printing, select Tray 1-
4 in the copier mode or with the
printer driver.
Cannot print in duplex
mode.
You have selected a tray that is set
to [Off]for duplex printing in [Tray
Paper Settings]under [System Set-
tings].
Select a paper tray in [Tray Paper
Settings]under [System Settings],
and then press [OK]. Then, select
[No Display (Plain Paper)]or [Recy-
cled Paper]for Paper Type, press
[Duplex], and then select [On]. See
“Tray Paper Settings”, General
Settings Guide.
The user code entry
screen is displayed.
Users are restricted by user man-
agement.
Enter the user code (up to eight
digits), and then press the {OK}or
{q}key.
The Authentication
screen appears.
Basic Authentication, Windows
Authentication, LDAP Authenti-
cation or Integration Server Au-
thentication is set.
Enter your login user name and
user password. See “When the
Authentication Screen is Dis-
played”, About This Machine.
“Temperature
Alert. Turn
main power off,
adjust room
temp. and wait a
while before
restarting.” ap-
pears, and printing is
disabled.
The temperature inside the ma-
chine is too high or too low.
Locate the machine in an environ-
ment where the temperature re-
mains between 10 and 32°C. See
p.93 “Where to Put Your Ma-
chine”.
Problem Cause Solution

When the Machine Does Not Operate As Wanted
8
1
Note
❒If you cannot make copies as you want because of paper type, paper size, or
paper capacity problems, use recommended paper. See “Copy Paper”, About
This Machine.
“You do not have
privileges to
use this func-
tion.” appears.
The use of the function is restrict-
ed to authenticated users only.
Contact the administrator.
Authentication failed. The entered login user name or
password is not correct.
Ask the administrator for the correct
login user name and password.
Authentication failed. Cannot access the authentication
server when using Basic Authenti-
cation, Windows Authentication,
LDAP Authentication, or Integra-
tion Server Authentication.
Contact the administrator.
Problem Cause Solution

When a Job Is Not Performed
9
1
When a Job Is Not Performed
If you cannot execute a function, it may be that the machine is being held up by
another function.
If you cannot execute a function, terminate any other functions currently active, and
then try executing the function again. In some cases, you can carry out another job (cop-
ier, facsimile, printer, or scanner) without canceling the current job being performed.
Performing multiple functions simultaneously like this is called “Multi-accessing”.
❖Combination Chart
…means that these functions can be used together.
…means that you can interrupt the current job with the function keys to pro-
ceed to a subsequent job.
…means that another job will automatically start after the current job is finished.
×…means that you must manually start another job after the current job is fin-
ished (i.e., these functions cannot be used together).
*1 You can scan a document once the preceding job documents are all scanned.
*2 During parallel reception, any subsequent job is suspended until reception is completed.
Mode after you select Copy Facsimile Printer Scanner
TWAIN
Transmission Operation
Transmission Reception
Receive Data
Print
Mode before you
select
Using the control panel Copying Scanning an Original for Memory Transmission Memory Transmission Immediate Transmission Memory Reception Printing Received Data Printing Using the control panel Scanning Scanning
Copy
Using the control panel ×× ×
Copying ×× *1 *1 *1 ×
Facsimile
Transmission Operation ×× × ×
Transmission
Scanning an Original for
Memory Transmission
×××× × ×××
Memory Transmission
××× ×
Immediate Transmission
××××××× ×××
Reception
Memory Reception ××× ×
Printing Received
Data
*2 *2 *2 ××
Printer
Receive Data
Print
Printing
Scanner
Using the control
panel ×××
Scanning *1 *1 *1 ×××
TWAIN
Scanning
×××××××× ×××

When the Machine Does Not Operate As Wanted
10
1
Note
❒If the machine is capable of executing multiple functions simultaneously,
specify which function should have priority in “Print Priority”. This setting is
factory-preset to “Display mode”. For setting of Printing Priority Function,
see “General Features”, General Settings Guide.
❒While printing is in progress, scanning a document using another function
may take more time.

11
2. Troubleshooting When
Using the Copy Function
This chapter describes likely causes of and possible solutions for copier function
problems.
When a Message Is Displayed
This section describes the machine's main messages. If other messages appear,
follow the instructions they contain.
Important
❒For messages that are not listed here, see “When You Have Problems Operat-
ing the Machine”.
Message Cause Solution
Cannot detect
original size
Improper original is placed. Select paper manually, not with
the Auto Paper Select function,
and do not use the Auto Re-
duce/Enlarge function. See
“Originals”, Copy Reference.
Cannot detect
original size
Improper original is placed. Input the both horizontal and
vertical sizes of the non-standard
original.
Cannot detect
original size
Improper original is placed. Place the original on the exposure
glass. See “Originals”, Copy Reference.
Cannot sort this
size.
The specified paper size is not
available with the Sort function.
This message appears when the by-
pass tray is selected. Use copy pa-
per that is not longer than 433 mm.
Cannot select
Bypass Tray in
current set-
ting.
The specified function is not
available with the bypass tray.
Select a paper tray other than the
bypass tray.
Original with
this length can-
not be duplex
scanned.
The specified custom length is not
available for duplex printing
from the ARDF (eg. 2 Sided →2
Sided, 2 Sided →1 Sided, 2 Sided
→Combine).
Do not place originals that are
longer than 433 mm.
Check original
orientation.
Original is not placed in a proper
orientation.
Change the orientation of the
original.
Check paper
size.
Improper paper size is set. If you press the {Start}key, copy
will start onto the selected paper.
Rotate Sort is
unavailable
with this paper
size.
A size of paper for which Rotate
Sort is not available is selected.
Select the proper paper size. See
“Sort”, Copy Reference.

Troubleshooting When Using the Copy Function
12
2
Reference
p.6 “When You Have Problems Operating the Machine”
Cannot dup. copy
this size.
Duplex mode does not support
the selected paper size.
Duplex mode supports the fol-
lowing paper sizes: A3
L ,
B4 JIS
L , A4 KL , B5 JIS KL ,
A5
KL , 11" × 17" L , 8
1
/
2
" × 14" L ,
8
1
/
4
" × 14" L , 8
1
/
2
" × 11" KL ,
7
1
/
4
" × 10
1
/
2
" KL , 8" × 13" L ,
8
1
/
2
" × 13" L , 8
1
/
4
" × 13" L , 8K L ,
16K
KL . Select one of these sizes.
Max. number of
sets is nn.
The number of copies exceeds the
maximum copy quantity.
You can change the maximum
copy quantity. See “Copier Fea-
tures”, General Settings Guide.
Cannot copy.
Original is be-
ing scanned by
another func-
tion.
The scanner function is in use. Cancel the current scan job. To do
this, press the {Clear/ Stop}key on
the scanner screen to display the
message “Clear/Stop key
was pressed. Stop scan-
ning?”, and then press [Stop].
You do not have
privileges to
use this func-
tion.
The use of this function is restrict-
ed to authentified users only.
Contact the administrator.
Authentication
failed.
The entered login user name or
password is not correct.
Ask the administrator for the correct
login user name and password.
Authentication
failed.
Cannot access the authentication
server when using Basic Authenti-
cation, Windows Authentication ,
LDAP Authentication, or Integra-
tion Server Authentication.
Contact the administrator.
Message Cause Solution

When You Cannot Make Clear Copies
13
2
When You Cannot Make Clear Copies
This section describes likely causes of and possible solutions for unclear copies.
Problem Cause Solution
Copies appear dirty. Image density is too dark. Adjust the image density. See
“Adjusting Image Density”,
Copy Reference.
Copies contain blots or
are patchy.
The machine is not on a level surface. Place the machine on a stable and
level surface.
Make sure the machine's environ-
ment meets requirements. See
p.93 “Where to Put Your Ma-
chine”.
Copies contain blots or
are patchy.
The paper is creased, curled, or
has blemishes.
Smooth out the wrinkles from the
paper, or replace it. See “Copy Pa-
per”, About This Machine.
If paper comes out curled, adjust
the Output Tray. See “Originals”,
Copy Reference.
Copies contain blots or
are patchy.
Image density is too light. Adjust the image density. See
“Adjusting Image Density”,
Copy Reference.
Copies contain blots or
are patchy.
The paper is damp.
Use paper that has been stored in
the recommended temperature and
humidity condition. See “Copy Pa-
per”, About This Machine.
Copies are too dark or
too light.
The correct paper type settings
are not made.
Check the paper loaded on the
paper tray or bypass tray matches
the paper type set on the display
panel. See “Copy Paper”, About
This Machine.
Copies are too dark or
too light.
The image was not printed on a
suitable surface.
Before printing on special paper,
check its surface carefully. Print-
ing on non-print surfaces reduces
print quality and can damage the
machine's internal components.
See “Copy Paper”, About This
Machine.
Copies are dirty. Use of non-recommended toner
can result in loss of print quality
and other problems.
Use manufacturer-genuine toner.
Contact your service representative.
The reverse side of an
original image is copied.
Image density is too dark. Adjust the image density. See
“Adjusting Image Density”,
Copy Reference.

Troubleshooting When Using the Copy Function
14
2
A shadow appears on
copies if you use past-
ed originals.
Image density is too dark. Adjust the image density. See
“Adjusting Image Density”,
Copy Reference.
Change the orientation of the original.
Put mending tape on the pasted area.
The same copy area is
dirty whenever mak-
ing copies.
The exposure glass, ADF or
ARDF is dirty.
Clean them. See p.97 “Maintain-
ing Your Machine”.
Copies are too light. Image density is too light. Adjust the image density. See
“Adjusting Image Density”,
Copy Reference.
Copies are too light. The paper is damp or rough.
Use the recommended paper. Also,
use paper that has been stored in
the recommended temperature and
humidity conditions. See “Copy
Paper”, About This Machine.
Contact your service representative.
Copies are too light. The toner bottle is almost empty. Add toner. See p.84 “Adding
Toner”.
Parts of images are not
copied.
The original is not placed correctly. Place originals correctly. See “Plac-
ing Originals”, Copy Reference.
Parts of images are not
copied.
The correct paper size is not selected. Select the proper paper size.
White lines appear. The exposure glass or scanning
glass is dirty.
Clean them. See p.97 “Maintain-
ing Your Machine”.
Copies are blank.
The original is not placed correctly. When using the exposure glass,
place originals face down. When
using the ADF or ARDF, place
them face up.
A moiré pattern is pro-
duced on copies.
Your original has a dot pattern
image or many lines.
Place the original on the exposure
glass at a slight angle.
Black spots appear on
the copy of a photo-
graphic print.
Because of high humidity, the
photographic print has stuck to
the exposure glass.
Place the print on the exposure glass
in either of the following ways:
• Place an OHP transparency on
the exposure glass, and then
place the print on top of the
OHP transparency.
• Place the print on the expo-
sure glass, and then place two
or three sheets of white paper
on top of it. Leave the expo-
sure glass cover, ADF or
ARDF open when copying.
Problem Cause Solution