Ricoh Aficio MP 7500 S/P Instruction and safety manual

______________________________________________
Page 1
Setting up Scan to Email
Basic information provided from the end user or the customer’s IT staff:
•Static IP for the copier
•Subnet Mask (use IPCONFIG Command if not provided)
•Gateway (use IPCONFIG Command if not provided)
•DNS server IP Address (use IPCONFIG Command if not provided)
•Email server name or server IP address ( Email server IP address is
recommended if there is no DNS)
•Email login name and password (only if authentication is required to email
out)
Setting up scan to email from the MFD’s web interface.
Step 1: Open Internet Explorer and type the IP address of the MFD.

______________________________________________
Page 2
Step 2: Click Login located on the upper right hand side of the window.
Type “admin” and click Login.
Step 3: Click “Configuration” located on the left hand side of the window.
Step 2: Click E-mail and input the email server name (example: mail.lacity.org) or
the email IP address (example: 161.149.50.30).

______________________________________________
Page 3
Step 3: Enter in a default sender name. In the “Administrator’s Email Address”
field enter your department name followed by “@LACITY.ORG”, make sure there
are no spaces between the department name. In the “SMTP Server Name” field
enter 161.149.50.30 then click OK when done. Leave the other fields as default.
Step 4: From the machine to enable “sender name default”, click “User Tools”,
“System Settings”, “File Transfer”, go to second page (click on “Next”), select
“Auto Specify Sender Name” and turn “ON”. Finally Click “OK” then “User
Tools” to exit.

______________________________________________
Page 4

______________________________________________
Page 5

______________________________________________
Page 6

______________________________________________
Page 7
Setting up LDAP
Step 1: Click on “LDAP Server”.
Step 2: Turn on “LDAP Search”. Select the first entry and click “Change” icon.
Step 3: Input the following information in the spaces provided:
Identification Name: CITY WIDE
Server Name: 10.32.127.205
Search Base: ou=users,o=cwdir
Authentication: ON
User Name: cn=eguide,ou=users,o=cwdir

______________________________________________
Page 8
After inputting all the information provided, click “Start” to check for validity.
Then click “OK” then “OK” again to save and close. Click on “OK” to leave the
LDAP setup screen.

______________________________________________
Page 9
Setting Up the Default File type (PDF vs TIF)
Step 1: From the scanning screen, click on “File Name/Type”. Then select the
desired file type default. Then click “OK”.

______________________________________________
Page 10
Step 2: Click on “Program” key located on the right hand side of the OP.
Step 3: Click on “Program as Defaults”.

______________________________________________
Page 11
Step 4: Select “Program”.
Step 5: Click “Yes”.
Screen will appear to confirm change.

______________________________________________
Page 12
Configuring LDAP and Email Defaults
Step 1: Click “User Tools”, then “Scanner Features”.
Note: The next step changes the Search default from the Address Book to LDAP.
Step 2: Click “Search Destination”, select “CITY WIDE” then click “OK”.

______________________________________________
Page 13
Note: The next steps changes the way the email is divided when the maximum
email size is reached.
Step 3: Click the “Send Settings” tab.
Step 4: Click on “Divide & Send E-mail” option. Then select “Yes (per Page)”
then click “OK”.
Step 5: Click “User Tools” to exit.

______________________________________________
Page 14
Using the LDAP feature to send Emails
Step 1: Select the scanning option from the MFD’s operation panel (OP).
Step 2: Click on “Search Dest.” Located at the top-center of the LCD touch screen.

______________________________________________
Page 15
Step 3: Make sure that “CITY WIDE” is highlighted, if not click to highlight. Then
click on E-mail Address.
Step 4: Type the name of the person you are trying to email using the onscreen
Qwerty Keyboard.

______________________________________________
Page 16
Step 5: Click “OK” after typing in the name. Then click on “Start Search” to begin.
Step 6: Select the recipient of the email by clicking on the email address. Then
click “OK”.
Step 7: Insert your document on the ADF of the RICOH MFD then click the
GREEN button.

______________________________________________
Page 17
Saving LDAP Search for Faster Access
Note: After you have selected a single destination within LDAP you have an
option to save that entry for faster access.
Step 1: Click “Prog Dest.”
Step 2: Verify the E-mail Address. Click “Names” to make searching for the email
address faster using our Frequent Send Option.

______________________________________________
Page 18
Step 3: Click “Change” under the “Name” and type the desired label. You may
also want to keep your destination in one of our Title Tabs. Note: The frequent tab
is the default, if you want to hide your destination from the frequent screen,
remove the highlight by clicking on “Frequent” again. Click “OK” when done.