Ricoh Pro C9200 Installation guide

1Input
CIP Training
Pro C9200 series

•
Jams and misfeeds can occur when printing on thick glossy sheets. To prevent such problems, be sure to
fan glossy sheets thoroughly before loading them.
When loading paper, set the paper direction according to its grain, as shown in the following diagram:
Tray 1
Direction of paper
grain
A3/11 × 17 tray unit,
Tray 2, or the wide LCT Multi bypass tray (Tray A)
Not recommended
CIP Training Pro C9200 series
Loading Paper
Do not stack paper over the limit mark
•Even if paper is loaded as described above, normal operations and print quality might still not
be possible, depending on the paper type.
•Prints might be noticeably curled. Flatten out prints if they are creased or curled. For details
about settings for flattening out curled paper, see "0301–0303 Correct Output Paper Curl",
Maintenance and Management.
•To prevent multiple sheets from being fed at once, fan the paper before loading it.
•If you load paper when only a few sheets of paper remain in the tray, multiple sheet feeding
may occur. Remove any remaining paper, stack them with the new sheets of paper, and then
fan the entire stack before loading it into the tray.
•Straighten curled or warped paper before loading.
•When paper in trays that are set to automatically eject unnecessary tab stock sheets runs out,
reload the tab stock from the beginning of the cycle (the first sheet).
•When you load paper into the paper tray for the first time or when you change the size or type
of paper in the paper tray, be sure to specify the appropriate paper settings in Tray Paper
Settings.
•You might at times hear a rustling noise from paper moving through the machine. This noise
does not indicate a malfunction

Loading Paper
1. Loosen the stack by riffling the sheets.
CVA068
2. Holding its shorter ends, flex the stack back and forth to create space between the sheets.
Repeat this several times.
CVA069
CVA070
3. Make sure there is space between the sheets.
CVA071
CIP Training Pro C9200 series

CIP Training Pro C9200 series
•
•
Check the paper edges are aligned at the left side.
When you use paper of Paper Weight 7 with a convex curl greater than 5 mm, paper of
Paper Weight 8 with a convex curl greater than 3 mm, or paper of Paper Weight 9 with
a convex curl, paper jam may occur if the height of the stacked paper is less than 4 mm.
To use paper in such condition, set the paper in the tray as follows:
•
Set as many as 5 to 10 more sheets than the number you intend to print
Correct the curl amount before setting the paper
Turn over the paper so the paper is with a concave curl.
Loading Large Capacity Trays
Loading Paper into Trays 1, 2, and the Wide Large Capacity Tray
Each paper tray is loaded in the same way.
The wide LCT is identified as Tray 3, Tray 4, Tray 5, Tray 6, Tray 7, and Tray 8.

Step: 2
Release the end fence by pressing and holding
green button. Move to back of tray.
Step: 1
Check that paper in the paper tray is not
being used, and then pull the tray carefully
out until it stops.
Remove paper if loaded.
Step: 3
gnidlohdnagnisserpybecnefedisehtesaeleR
both green buttons together. Move side
fences to maximum width of tray.
Loading Large Capacity Trays
CIP Training Pro C9200 series

Step: 4
Load paper by aligning the paper with the left
side of the paper tray.
Place paper with print side up.
Load a stack of paper about 5–10 mm high.
Make sure the paper rest on top of the
supporting plates on both sides.
Step: 5
Load additional sheets, if necessary.
Do not stack paper over the limit mark.
Step: 6
Tightly fit the end fence to the loaded paper,
and then re-lock the end fence again.
Make sure there are no gaps between the
paper and end fence.
Carefully slide the paper tray fully in.
Loading Large Capacity Trays
CIP Training Pro C9200 series

2,200 sheets. (Capacity using 80 gsm uncoated paper)
Specifications.
Capacity:
Weight: Paper weight 6: 220.1 to 256.0 gsm
Paper weight 7: 256.1 to 300.0 gsm
Paper weight 8: 300.1 to 360.0 gsm
Paper weight 9: 360.1 to 470.0 gsm
Paper weight 1: 52.3 to 63.0 gsm
Paper weight 2: 63.1 to 80.0 gsm
Paper weight 3: 80.1 to 105.0 gsm
Paper weight 4: 105.1 to 163.0 gsm
Paper weight 5: 163.1 to 220.0 gsm
Type: Plain paper, Recycled paper, Uncoated papers, Coated matt and glossy
paper, Preprinted paper, Letterhead, Labels, Pre-punched paper, Tab
stock, Envelopes, Translucent paper, Textured, Transparency, and other
special and synthetic materials as defined in the Master Library.
Supporting plates
DER093
When loading small stock.
When you load paper that is 204 mm or
smaller, remove the supporting plates from
the bottom of the paper tray.
Store them in the pocket on the right-hand
side of the paper tray.
Set the paper flush against the protrusions in
the bottom of the inner side fence.
Check that the scale numbers on the top of
the side fences are roughly the same.
Loading Large Capacity Trays
CIP Training Pro C9200 series

Step: 2
Attach the tab fence, and then align the end
fence gently against the paper you loaded
while pressing the release button of the end
fence.
Carefully slide the paper tray fully in.
NOTE: Replace the tab fence after use.
When loading tab stock, attach the tab fence.
Step: 1
Check that paper in the paper tray is not
being used, and then pull the tray carefully
out until it stops.
Take out the tab fence from the pocket on the
right-hand side of the paper tray.
Set the side fences to the size of the tab stock
to be loaded, and then load it.
Loading Large Capacity Trays
CIP Training Pro C9200 series

Step: 1
Set the side fences to the paper size, and
then square the paper and load it print side
up.
Do not stack paper over the limit mark.
Loading Paper into the Multi Bypass Tray (Tray A)
CIP Training Pro C9200 series
Use the multi bypass tray (Tray A) to use transparencies, translucent paper, and paper that
cannot be loaded in the paper trays.
•The maximum number of sheets you can load at the same time depends on paper type. Do not
stack paper over the limit mark. For the maximum number of sheets you can load.
•Check the paper edges are aligned at the left side.
•When loading a low number of sheets, be sure not to squeeze the side fences in too tightly. If
the side fences are squeezed too tightly against the paper, the edges may crease, the paper may
misfeed, or if it weighs between 52.3–63.0 g/m2 (14.0–16.9 lb. Bond), it may wrinkle.
DER069
Step: 2
Set the end fence.
222
DER070
1
1. End fence
2. Extender