Ricoh Ri 100 User manual

DSA121
DSB130
Mode indicator
*1
• Light: Press the [Preheat] key to start preheating
• Flashing: Preheating under way
• Off: Preheating completed
Cassette
Printer
(Ri 100)
Finisher
(This machine Rh 100)
Front Cover
Mode Switching
Lever
Time/temperature indicator [Temperature] key [Preheat] key*1 [Power] key
[Fixing Time] key [Stop/Unlock] key
Control Panel
Guide to Components of the Finisher
This guide describes the basic printing procedures using the
printer and this machine. In the next pages, the procedures
for each step and particular cautions are explained.
For safe and correct use, be sure to read Safety Information
before using the machine.
Quick Guide

1Loading the fabric in the cassette
For details, refer to User’s Guide provided with the printer Ri 100.
You can shorten the processing time by putting a garment in the cassette while pre-
heating the finisher.
➊
Press the [Power] key to turn on the power.
➑
When you move the mode switching lever to the
left, processing starts. An alarm sounds after
preheating is completed.
➋
Make sure the mode switching lever is set in the
center.
➒
➌
Set the temperature of the heater.
Set the temperature according to the fabric on
which you are printing. The default setting is “High”.
❿
Confirm that the mode indicator light is off.
➍
When the [Preheat] key is lit, press the [Preheat]
key to start preheating.
When the [Preheat] key is unlit, no operation is
necessary because preheating is completed.
⓫
Press the [Stop/Unlock] key for 1 second or
more to open the cover. When set to the profes-
sional mode, it is not necessary to hold down
the [Stop/Unlock] key.
➎
Press the [Stop/Unlock] key for 1 second or
more to open the cover. When set to the profes-
sional mode, it is not necessary to hold down
the [Stop/Unlock] key.
⓬
➏ ⓭
➐
2
Smoothing wrinkles/flattening fibers (Press )

3Printing
For details, refer to User’s Guide provided with the printer Ri 100.
➊
Make sure the mode switching lever is set in the
center.
➑
➋
Set the temperature of the heater.
Set the temperature according to the fabric on
which you are printing. The default setting is
“High”.
➒
When you move the mode switching lever to the
right, processing starts. An alarm sounds after
preheating is completed.
➌
Set the amount of time that the heater is on.
Set the time according to the fabric on which
you are printing. The default setting is “Medium”.
❿
➍
When the [Preheat] key is lit, press the [Preheat]
key to start preheating.
When the [Preheat] key is unlit, no operation is
necessary because preheating is completed.
⓫
Confirm that the mode indicator light is off.
➎
Press the [Stop/Unlock] key for 1 second or
more to open the cover. When set to the profes-
sional mode, it is not necessary to hold down
the [Stop/Unlock] key.
⓬
Press the [Stop/Unlock] key for 1 second or
more to open the cover. When set to the profes-
sional mode, it is not necessary to hold down
the [Stop/Unlock] key.
➏ ⓭
➐ ⓮
4Fixing ink (Fix )

Basic Usage of the Finisher
CAUTION:
If children use this machine, their parents must be with them and they should be very careful in using•
this machine. Otherwise, injury or burns may result.
The finisher has “Standard mode” and “Professional mode”.
Standard mode
◆
The factory-default setting is standard mode. The finisher has the following functions
to prevent children from touching the inside of the finisher accidentally when it is very
hot.
When the inside of the finisher exceeds 70 °C (158 °F), the front cover locks. To•
open the front cover, press the [Stop/ Unlock] key for at least 1 second.
Professional mode
◆
To use this mode, switch from standard mode.
As this mode is for users who are accustomed to using the finisher, the front cover
does not lock even when the temperature of the inside of the finisher exceeds 70 °C
(158 °F).
However, during press processing and fixing processing, the front cover locks regard-
less of whatever mode is used to prevent erroneous operations.
How to Switch Between Stan-
◆
dard Mode and Professional
Mode
Press the [Temperature] key and [Fix-
ing Time] key simultaneously for at
least 2 seconds.
DSB547
Unlock Cover
◆
When set to standard mode, press
the [Stop/ Unlock] key for at least 1
second.
DSB548
When set to the professional mode,
it is not necessary to hold down the
[Stop/Unlock] key.
© 2017 Ricoh Co., Ltd.
EN GB EN US EN AU J361-6607C