Ricoh Ri 2000 User manual

Original instructions
RICOH Ri2000
Option Platen
User Guide
For Hat Platen/Shoe Platen/Sleeve Platen

TABLE OF CONTENTS RICOH Ri 2000 User Manual
2
TABLE OF CONTENTS
TABLE OF CONTENTS..........................................................................................................2
How to Read the Manuals .....................................................................................................3
Before You Begin.............................................................................................................................. 3
Disclaimer......................................................................................................................................... 3
Notes................................................................................................................................................. 3
1. Printing Method................................................................................................................4
1.1. Setup Printer..................................................................................................................................... 4
1.2. Printing method for RIP.................................................................................................................... 4
2. Troubleshooting Guide..................................................................................................10
3. Appendix.........................................................................................................................11
3.1. Revision history.............................................................................................................................. 11

How to Read the Manuals RICOH Ri 2000 User Manual
3
How to Read the Manuals
Before You Begin...
Only appropriately trained users should operate the machine.
Disclaimer
Contents of this manual are subject to change without prior notice.
To the maximum extent permitted by applicable laws, in no event will the manufacturer be liable for any
damages whatsoever arising out of failures of this machine, losses of the registered data, or the use or
non-use of this machine and operation manuals provided with it.
Make sure that you always copy or have backups of the data registered in this machine. Documents or
data might be erased due to your operational errors or malfunctions of the machine.
In no event will the manufacturer be responsible for any documents created by you using this machine or
any results from the data executed by you.
Notes
Read this manual carefully before you use the machine and keep it handy for future reference.
For safe and correct use, be sure to read Safety Information before using the machine.
The manufacturer will not be responsible for any damage or expense that might result from the use of
parts other than genuine parts from the manufacturer with your products.
For good output quality, the manufacturer recommends that you use genuine ink from the manufacturer.
Some illustrations in this manual may be slightly different from the machine.
Certain options may not be available in some countries. For details, please contact your local dealer.
Depending on which country you are in, certain units may be optional. For details, please contact your
local dealer.

1. Printing Method RICOH Ri 2000User Manual
4
1. Printing Method
1.1. Setup Printer
Refer to Ricoh Ri series Direct to Garment Printer Platen Manual.
IMPORTANT! The version of printer firmware (Panel GIB) must be 1.03.0 or later. If not, download
the latest firmware from RICOH official website. At that time, please also update the firmware of Sub
Control(SCB) and Engine(CTL) to latest version.
1.2. Printing method for RIP
Start Textile Productionsever.
Input the image to Textile Productionsever .
Please set with RIP according to the platen type.
Platen type Textile Productionserver
Hat a) User select Media size
(*1)
Sleeve a) User select Media size
Shoe a) User select Media size
b) User set Offset/Scaling

1. Printing Method RICOH Ri 2000User Manual
5
(CAUTION *1)
The image is printed 180 degrees inverted from the display on the Textile
Productionserver.
In that case, the user should set 180 degrees.
The print settings are below.
Default Settings: After Set Rotate(180 degree)

1. Printing Method RICOH Ri 2000User Manual
6
a) User select Media size.
Textile Productionserver:
b) User set Offset/Scaling
According to type of Shoe Attachment, user set Height x Width, Offset x, y.
Offset Y
Printer
Distance between printable
areas
Printable Area (Width)
Offset X
Printable Area (Height)

1. Printing Method RICOH Ri 2000User Manual
7
If you want to print on both feet, please prepare the following image and set Offset x,y.
Offset of each Shoe attachement
Shoe
Attachment
Offset
(Reference)
Printable Area(Width x Height)
(Reference)
Distance between printable areas
Small
X:20 Y:220
85 x 150 mm
205 mm
Medium
X:40 Y:360
50 x 50 mm
40 mm
Large
X:40 Y:350
60 x 60 mm
40 mm
Setting method of Textile Productionserver:

1. Printing Method RICOH Ri 2000User Manual
8
Default Settings: After Set Offset(X =40, Y=350)
Enable the Optional Platen.
a) Press the Setting tab on the touch panel of the machine.
b) Press [OPTION]
c) Go to the 3rd page and enable [Optional Platen].

1. Printing Method RICOH Ri 2000User Manual
9
Attaching the Optional Platen on the printer.
Adjusting the Height of the Optional Platen
a) Flatten the clothes set onto the optional platen as much as possible.
b) Press [HEIGHT ADJUST].
c) Select the Platen.
IMPORTANT! Select the same platen as the set platen(on the step 3 and 5).
If you select a different platen, the platen may hit the printer body.
User print image in Textile Productionserver.
Press [PRINT START].

2. Troubleshooting Guide RICOH Ri 2000User Manual
10
2. Troubleshooting Guide
Issue/ Error Causes Solutions
If SC920 occurred
when the hat platen
was set in the state
shown in the photo on
the right.
Things may be hitting the
shutter.
↑The hat is jammed at the
entrance.
↑If you open the front cover,
it looks like the picture above.
(1)Please turn off the power first.
(2)Next, gently pull the platen toward the
front of the printer by your hands until
the things no longer hit the shutter.
(3)Then turn on the power again.
And when you printing, make sure that
the RIP setting and the platen selection
match the actual platen type.
shutter
shutter
hat