Ricoh SG Series Use and care manual

1
About SG Series Firmware Updates
(Web Image Monitor)
TABLE OF CONTENTS
1. About Firmware Updates .........................................................................2
2. Operating Environment............................................................................2
3. Disclaimer..................................................................................................2
4. Caution........................................................................................................2
5. Firmware Update Operating Instructions...............................................3
6. Wireless LAN Update Operating Instructions.....................................10
7. Trademarks..............................................................................................21

2
1. About Firmware Updates
This manual explains how to update the software for SG series network boards.
2. Operating Environment
A Web browser is required for use.
To use the Web browser, specify the TCP/IP protocols of your computer and the ma-
chine.
3. Disclaimer
The manufacturer is not liable for any damages resulting from use or misuse of this
software.
Nor is the manufacturer liable for any damages resulting from use or misuse of this
software with third parties.
4. Caution
To update the firmware to version 2.0.0 or later, the current firmware must be version
1.9.0.
If the current firmware is earlier than version 1.9.0, update it first to version 1.9.0, and
then to version 2.0.0 or later.
To check the firmware version, print the configuration page.
[/Menu] [List/Test Print] [Config. Page]

3
5. Firmware Update Operating Instructions
These instructions explain how to update the firmware of the machine.
Before you start the update, make sure of the following:
The machine is in standby mode.
No applications are running on the computer.
The following procedure uses Windows 7 screenshots.
1. Open a Web browser.
2. Enter "http://(the machine's IP address or host name)/" in the address bar.
CHU266
•
•

4
3. Click [Administrator Login].
CHU267
The following screen appears.

5
4. Enter the login name and password, and then click [OK].
The default login name for administrators is "admin". No login password is set up.
To ensure security, it is important you change the password.
CHU282
5. In the menu area, click [Settings].
CHU268

6
6. Click [ROM Update].
CHU269
7. Select the update file (***.bin).
Enter the path to the file in [Firmware File Name] or click [Browse...] and select the
file.
CHU279

7
8. Click [Update].
CHU280
Updating starts.
When the update file transfer completes, the following message appears:
The update takes a while. Do not operate the Web browser, computer, or the ma-
chine while updating. The update progress appears on the machine's control pan-
el.

8
9. Click [OK].
CHU277
The rebooting takes a while. Click [OK] after it reboots.
The display returns to the ROM Update page.
If DHCP has been enabled, the IP address might be updated, resulting in the Web
browser not returning to the top page. If the top page does not appear, check the IP
address using the machine's control panel and try connecting again.

9
10. Check the current firmware version.
CHU278
If it has been updated, the update has completed successfully.
Otherwise, turn the power off and back on, and then try this procedure again from
Step 1.

10
6. Wireless LAN Update Operating Instructions
These instructions explain how to update the wireless LAN of SG 3110DW.
Before you start the update, make sure of the following:
The machine is in standby mode.
A wireless LAN connection is active.
No applications are running on the computer.
The following procedure uses Windows 7 screenshots.
1. Open a Web browser.
2. Enter "http://(the machine's IP address or host name)/" in the address bar.
CHU266
•
•
•

11
3. Click [Administrator Login].
CHU267
The following screen appears.

12
4. Enter the login name and password, and then click [OK].
The default login name for administrators is "admin". No login password is set up.
To ensure security, it is important you change the password.
CHU282
5. In the menu area, click [Settings].
CHU268

13
6. Click [Wireless LAN Settings].
CHU283

14
7. Select the update file (***.bin).
Enter the path to the file in [Firmware File Name] or click [Browse...] and select the
file.
CHU270

15
8. Click [Update].
CHU271
Updating starts.

16
When the update file transfer completes, the following message appears:
The update takes a while. Do not operate the Web browser, computer, or the ma-
chine while updating. The update progress appears on the machine's control pan-
el.

17
9. Click [OK].
CHU272
The rebooting takes a while. Click [OK] after it reboots.
The display returns to the ROM Update page.
If DHCP has been enabled, the IP address might be updated, resulting in the Web
browser not returning to the top page. If the top page does not appear, check the IP
address using the machine's control panel and try connecting again.
10. Check the version in "Wireless LAN Settings".
CHU273

18
11. Click [Cancel].
CHU284
12. Click [Home].
CHU274

19
13. Click [Device Info].
CHU275
14. Check the version in "Wireless LAN".
CHU276
If it has been updated, the update has completed successfully.

20
Otherwise, turn the power off and back on, and then try this procedure again from
Step 1.