RIGHT ANGLE NewCrank 3.5 Series User manual

DETAIL A
3
12
5
4
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
STEPS 1-4
2
1
WORKSURFACE
SUPPORT
A
PAGE 1 OF 3
VERSION DATED: 8/20/14
TOOLS REQUIRED FOR ASSEMBLY:
POWER DRIVER W/ADJUSTABLE
TORQUE
#2 PHILLIPS HEAD DRIVER BIT
#2 SQUARE HEAD DRIVER BIT
SMALL PHILLIPS SCREWDRIVER
3/16 HEX HEAD DRIVER BIT OR
ALLEN WRENCH
TAPE MEASURE
LEVEL
NewCr nk SERIES 3.5 HEIGHT ADJUSTABLE WORKSTATION ASSEMBLY
INSTRUCTIONS:
STEP 1: LAY THE WORKSURFACE 1 ON A PROTECTED SURFACE WITH THE
PILOT HOLES FACING UP. ALIGN THE HOLES IN THE WORKSURFACE SUPPORT
ON THE LEG ASSEMBLY WITH THE PILOT HOLES IN THE WORKSURFACE. NOTE
THAT THE CRANK CAN BE INSTALLED ON EITHER LEG ASSEMBLY.
STEP 2: PLACE A CLAMP 4 ON THE CRANK HANDLE ASSEMBLY 3 . SLIDE THE
HANDLE ASSEMBLY INTO THE CRANK BRACKET 5 . PLACE THE OTHER CLAMP
ONTO THE HANDLE ASSEMBLY ON THE OPPOSITE SIDE OF THE CRANK HOLDER
FROM THE FIRST CLAMP. DO NOT TIGHTEN THE SCREWS IN THE CLAMPS.
STEP 3: INSERT THE HANDLE/CLAMP/BRACKET ASSEMBLY INTO THE HEX DRIVE
NEAR THE TOP OF THE LEG ASSEMBLY 2 UNTIL IT BOTTOMS OUT. YOU MAY NEED
TO TURN THE CRANK HANDLE ASSEMBLY SLIGHTLY TO ALIGN IT WITH THE HEX
DRIVE. ATTACH THE CRANK BRACKET 5 TO THE WORKSURFACE 1 WITH (4)
WOOD SCREWS 12 . DO NOT USE ANY PILOT HOLES. DO NOT OVERTIGHTEN
THE SCREWS. USE A LOW TORQUE SETTING ON THE DRIVER. THE WORKSURFACE
MATERIAL COULD STRIP.
STEP 4: SLIDE THE FORWARD CLAMP 4 AGAINST THE CRANK BRACKET 5 AND
TIGHTEN THE CLAMP SCREW. USE A SMALL PHILLIPS SCREWDRIVER. DO NOT
OVER-TIGHTEN THE SCREW. IT COULD STRIP. SLIDE THE CRANK HANDLE ASSEMBLY
OUT OF THE CLAMP BRACKET UNTIL IT JUST CLEARS THE FRONT OF THE WORK-
SURFACE. SLIDE THE BACK CLAMP AGAINST THE BACK OF THE CRANK BRACKET
AND TIGHTEN THE CLAMP SCREW.
INSTRUCTION # 53238 HARDWARE PACK # 53222 OR 53239
ITEM # PART # DESCRIPTION QTY
1 VARIES Series 3.5 Worksurface 1
2 VARIES NewCrank Series 3.5 Left Leg Assembly 1
3 VARIES NewCrank Series 3.5 Crank Handle Assembly 1
4 53141 NewCrank Clamp W/Screw 1
5 801315 Ketterer Crank Bracket 1
6 VARIES NewCrank Series 3.5 Hex Rod 1
7 VARIES NewCrank Series 3.5 Right Leg Assembly 1
8 VARIES Series 4 Cross Support 1
9 53025 5/16 Lock Washer 4
10 53024 5/16-18 x 1/2 Button Head Socket Screw 4
11 800934 Cross Support End Cap 2
12 51708 M5 x 18mm (7/8 ) Sq/Ph/Wshr Head Wood Screw 28
13 VARIES Series 4 LT 48 U-Channel 1

11
2
7
9
13
10
12
8
LEVELING GLIDE
12
STEPS 6-10
PRE-INSTALLED
WELD NUTS
STEP 8: INSERT (2) END CAPS 11 INTO THE ENDS OF THE CROSS SUPPORT 8 .
STEP 9: ATTACH THE LEG ASSEMBLIES 2 AND 7 TO THE WORKSURFACE 1 USING (16) WOOD SCREWS 12 .
DO NOT OVER-TIGHTEN THE SCREWS. USE A LOW TORQUE SETTING ON THE DRIVER.
STEP 10: CENTER THE U-CHANNEL 13 ON THE HEX ROD 7 AND BETWEEN THE LEG ASSEMBLIES 2 AND 7 .
DO NOT USE ANY PILOT HOLES. ATTACH THE U-CHANNEL WITH (8-12 ) WOOD SCREWS 12 .
STEP 11: WITH THE HELP OF AN ASSISTANT, SET THE WORKSTATION UPRIGHT IN ITS FINAL LOCATION. LEVEL THE
WORKSTATION IF REQUIRED BY TURNING THE LEVELING GLIDES CLOCKWISE (FROM THE TOP) ON THE LOW
CORNERS OF THE UNIT. IF YOUR WORKSTATION HAS CASTERS, LEVEL IT BY TURNING THE BOLTS ON THE TOP OF
THE CASTERS. THE WORKSTATION IS NOW READY FOR USE.
4.000
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
STEP 5
1
6
B
PAGE 2 OF 3
DETAIL B
.
STEP 5: INSERT THE HEX ROD 6 INTO THE HEX DRIVE NEAR THE TOP OF THE LEG ASSEMBLY WITH THE CRANK
ASSEMBLY ATTACHED. PLACE THE OTHER LEG ASSEMBLY ON THE WORKSURFACE INSERTING THE OTHER END OF
THE HEX ROD INTO THE HEX DRIVE.
STEP 6: WITH THE HELP OF AN ASSISTANT, PLACE (4) WASHERS 9 ON (4) SOCKET SCREWS 10 . INSERT THESE
THROUGH THE HOLES AT THE ENDS OF THE CROSS SUPPORT 9 AND THREAD THEM INTO THE WELD NUTS PRE-
INSTALLED IN THE LEG ASSEMBLIES. SEE DETAIL B. DO NOT FULLY TIGHTEN.
STEP 7: LEVEL THE CROSS SUPPORT 8 AT 4 FROM THE BOTTOM OF THE WORKSURFACE SUPPORT. SEE
DETAIL C. FULLY TIGHTEN THE SOCKET SCREWS 10
DETAIL C

PAGE 3 OF 3
TROUBLESHOOTING: IF YOU ARE HAVING ANY PROBLEMS WITH THE TABLE
OPERATION, CONTACT RIGHTANGLE™ SERVICE AT 800-298-4351 OR
[email protected]
WARRANTY INFORATION: NewHeights™ PRODUCTS ARE WARRANTED TO BE
FREE OF DEFECTS DUE TO MANUFACTURING OR MATERIALS AS FOLLOWS:
2 YEARS ON THE GEARS. 5 YEARS ON THE SUPPORT BRACKETS, ALUMINUM
COLUMNS AND FEET. WE WILL REPLACE ANY DEFECTIVE PART AFTER INSPECTION
BY AN AUTHORIZED AGENT. COSTS INCURRED DUE TO PRODUCT REPLACEMENT
SUCH AS INSTALLATION LABOR OR TRANSPORTATION ARE NOT COVERED UNDER
THIS WARRANTY.
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING