RIGHT ANGLE R-STYLE PLAN 1 WORKSTATION User manual

PAGE 1 OF 2
VERSION DATED: 2/1/12
TOOLS REQUIRED FOR ASSEMBLY:
CORDLESS DRILL
#2 PHILLIPS HEAD DRIVER BIT
TAPE MEASURE
LEVEL
R-STYLE PLAN 1 WORKSTATION ASSEMBLY INSTRUCTIONS:
STEP 1: LAY THE WORKSURFACE 1 ON A PROTECTED SURFACE WITH THE
INSERTS AND PILOT HOLES FACING UP. ASSEMBLE THE RIGHT LEG ASSEMBLY
4 , THE MODESTY PANEL 5 , AND THE LEFT LEG ASSEMBLY 3 USING (3)
MACHINE SCREWS 9 INTO EACH LEG ASSEMBLY. DO NOT FULLY TIGHTEN THE
SCREWS. IF YOUR WORKSTATION HAS THE OPTIONAL WIRE MANAGEMENT
CHANNEL, INSTALL IT ACCORDING TO THE INSTRUCTIONS THAT CAME WITH
THE CHANNEL.
STEP 2: PLACE THE LEG AND MODESTY PANEL ASSEMBLY ON THE WORKSUR
FACE 1 ALIGNING THE HOLES IN THE WORKSURFACE SUPPORTS WITH THE
INSERTS IN THE WORKSURFACE. ATTACH IT USING (3) MACHINE SCREWS
1
ON THE LONG LEG AND (2) MACHINE SCREWS ON THE SHORT LEG. FULLY
TIGHTEN ALL THE FASTENERS INCLUDING THE SCREWS HOLDING THE MODESTY
PANEL 5 TO THE LEFT LEG ASSEMBLY 3 AND THE RIGHT LEG ASSEMBLY 4 .
ATTACH THE TOP EDGE OF THE MODESTY PANEL TO THE WORKSURFACE
USING (3) OR (4) WOOD SCREWS 8 INTO THE PILOT HOLES ON THE WORK
SURFACE. DO NOT OVER TIGHTEN THE SCREWS. USE A LOW TORQUE SETTING
ON THE DRILL.
STEP 3: CENTER (2) JOINER PLATES 7 ON THE EDGE OF THE WORKSURFACE
THAT WILL BUTT THE CENTER SECTION. PLACE THEM 1" FROM THE FRONT AND
BACK EDGES OF THE WORKSURFACE 1 . FASTEN WITH (2) WOOD SCREWS 8
IN EACH JOINER PLATE.
STEP 4: LAY THE WORKSURFACE 1 ON A PROTECTED SURFACE WITH THE
PILOT HOLES FACING UP. ALIGN THE HOLES IN THE PLATE AT THE TOP OF THE
POST LEG 2 WITH THE PILOT HOLES AT THE BACK EDGE OF THE WORK
SURFACE. ATTACH THE POST LEG WITH (4) WOOD SCREWS 8 .
INSTRUCTION # 51268 HARDWARE PACK # 51267
READ ALL THE
INSTRUCTIONS
BEFORE BEGINNING
ITEM # PART # DESCRIPTION QTY.
1 VARIES WORKSURFACES 3
2 29sl 29SL POST LEG 2
3 VARIES R STYLE LEFT LEG ASSY 1
4 VARIES R STYLE RIGHT LEG ASSY 1
5 VARIES R STYLE MODESTY PANEL 1
6 50824 R STYLE 420mm RIGHT 1
7 800512 2 X 2 WORKSURFACE JOINER PLATE 4
8 51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW 27
9 50133 10 32 x 1/2 PHILLIPS TRUSS HEAD MACHINE SCREW 6
10 R STYLE A 6 x 15mm MACHINE SCREW 5
2
8
1
STEP 4
CENTER SECTION
1
3
7
8
8
9
10
5
4
STEPS 1-3
LEFT SECTION
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING

PAGE 2 OF 2
STEP 5: LAY THE WORKSURFACE 1 ON A PROTECTED SURFACE WITH THE PILOT HOLES FACING UP. ALIGN
THE HOLES IN THE PLATE AT THE TOP OF THE POST LEG 2 WITH THE PILOT HOLES IN THE WORKSURFACE.
ATTACH THE POST LEG USING (4) WOOD SCREWS 8 . ATTACH (2) JOINER PLATES 7 AS YOU DID ON THE
LEFT SECTION.
STEP 6: WITH THE ASSISTANCE OF A HELPER SET THE LEFT AND RIGHT SECTIONS UPRIGHT IN THEIR FINAL
LOCATION. SET THE EDGES OF THE CENTER SECTION ON THE JOINER PLATES ON THE LEFT AND RIGHT
SECTIONS OF THE WORKSTATION. ATTACH THE LEFT AND RIGHT SECTIONS TO THE CENTER SECTION WITH
(2) WOOD SCREWS 8 IN EACH JOINER PLATE.
STEP 7: LEVEL THE WORKSTATION BY TURNING THE LEVELING GLIDES CLOCKWISE (FROM THE TOP) ON THE
LOW CORNERS OF THE UNIT.
7
8
STEP 6
1
2
8
8
7
6
10
STEP 5
RIGHT SECTION
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
VERSION DATED: 2/1/12
K&A MANUFACTURING