RIGHT ANGLE NewHeights Elegante XT Series User manual

Instruction #53210 • Dated: 02/21/2019
NewHeights™ Series 4 Elegante XT 3-Leg Workstation
Workstation Assembly Instructions
Warranty: raproducts.com/warranty
1 of 10

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 2 of 10
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
USE THIS PRODUCT ONLY AS INSTRUCTED.
FAILURE TO COMPLY WITH ALL INSTRUCTIONS AND WARNINGS
MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY.
Basic Safety Instructions
1. Intended Use. This Product is exclusively designed for use as indoor ofce furniture in compliance with all instructions and safety warnings
in the user manual. Any different use, or use extending beyond the intended use, may result in property damage or bodily injury and is
prohibited. This Product should not be used, operated or maintained with additional components not authorized by K&A Manufacturing, Inc.
BY USING THIS PRODUCT OR ANY FEATURE OF THIS PRODUCT, YOU AGREE TO COMPLY WITH ALL PRODUCT TERMS
AND POLICIES, INCLUDING WITHOUT LIMITATION ANY SAFETY WARNINGS AND INSTRUCTIONS, PROVIDED BY
K&A MANUFACTURING, INC. AND ITS AFFILIATES. K&A MANUFACTURING, INC. SHALL ASSUME NO LIABILITY FOR ANY
DAMAGE OR INJURY CAUSED BY USE OF THE PRODUCT A) IN VIOLATION OF ANY SAFETY WARNINGS OR INSTRUCTIONS;
B) NOT AUTHORIZED BY K&A MANUFACTURING, INC.; OR C) BY EVENTS BEYOND K&A MANUFACTURING, INC.’S CONTROL.
DO NOT SIT, STAND OR CRAWL ON OR UNDER THE PRODUCT.
MAKE SURE NO OBSTACLES ARE IN THE PRODUCT’S PATH.
MAKE SURE ALL CORDS ARE LONG ENOUGH TO ACCOMMODATE ANY CHANGE IN HEIGHT.
DO NOT USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURER.
2. Electrical Height Adjustment. The height of this Product may be adjusted electronically. Contact with electrical voltage may cause serious
injury and death. Only use the Product in compliance with these instructions. This Product should not be used in environments with high
levels of humidity or moisture.
KEEP CORDS AND ELECTRICAL COMPONENTS AWAY FROM HEAT AND LIQUIDS.
DO NOT OPEN ANY OF THE COMPONENTS: CONTROL BOX OR KEYPAD.
DO NOT USE WITH A DAMAGED PLUG OR CORD.
DO NOT INSERT ANYTHING INTO ANY SEAM OR OPENING.
3. Setup and Use. This Product should only be used and operated in good condition. When in use, no one should sit, stand or crawl on or
under the Product. There is a danger of crushing, shearing, injury or damage. Keep the entire range of motion of the Product clear of all
obstacles. Devices and object on the Product can tip over, fall or be crushed by the Product.
KEEP HANDS AND FINGERS CLEAR.
KEEP ALL OBSTACLES CLEAR OF THE PRODUCT’S PATH.
4. Users. This Product is not intended for use with children, individuals with restricted physical, sensory or mental capabilities, or individuals
who lack experience or knowledge, unless they are supervised by a person who is responsible for their safety or they have received
instructions from a person who is responsible for their safety concerning how the Product must be used. Children should be closely
supervised to ensure that they do not play with the Product and its height adjustment mechanism to avoid risk of physical injury or
electric shock.
KEEP CHILDREN AWAY FROM THE PRODUCT, ITS CONTROL UNITS, AND KEYPADS.
WARNING
DANGER

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 3 of 10
Q
Left Leg
R
Right Leg
Motor box faces inside of table.
Do not allow the leg assemblies
to stand without support.
Your workstation will have either two left legs (Q) and one right leg (R) or two right legs and one left leg.
The drawing below shows how to distinguish the left leg from the right leg.
Left Return
Right Return
Leg Q
Leg R
Leg Q
Leg Q
Leg R
Leg Q
Leg R
Front
Front

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 4 of 10
E. 10 x 5/8” Round Washer Head Wood Screw x41
F. 5/16”x 18-3/8” Button Socket Cap Screw x6
G. 1/4 Blk Flat Washer x4
H. 1/4-20 x 1/2 Blk Ph Hd Machine Screw x4
I. Cable Clamp 3/16 Black x4
J. 8 x 3/4” Pan Head Wood Screw x4
K. Joiner Plate (Optional)
Tools Required for Assembly
A. Power Driver with Adjustable Torque
B. #2 Phillips Head Driver Bit
C. #2 Square Head Drive Bit
D. Level A B C D
Hardware and Tools Included for Assembly (may have extra)
E F G H
I J
Elegante Parts
L. Wire Management (size varies) x2
M1. Two Button Up/Down Switch x1
M2. Four Button Programmable Up/Down Switch x1
Optional - If you have a programmable
switch, please refer to the installation
instructions included with the switch
N. Control Box for Three Motors x1
O. Power Cord x1
P. Power Strip x1
Q XT Left Leg x1 or 2
R. XT Right Leg x1 or 2
L
M1 M2
N
O
P
Q R
K

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 5 of 10
Step 1
• Lay the worksurface on a protected surface with the pilot
holes facing up. If your worksuface has a seam, lay the
joiner plate centered on the seam about 3” from the front.
• Attach worksurface with eight wood screws.
Pilot holes are not provided, screws are self drilling.
• Set the legs on the worksurface,
align the legs over the pilot holes.
• Attach the legs onto the
worksurface with six wood
screws. Do not tighten.
Step 2
• Your workstation may have two different size
wire management. Determine the correct
location of the wire management channels
according to the size of the worksurface.
• Slide apart the wire management and attach
with four machine screws. Do not tighten.
• Install wood screws through the wire
management and into the worksurface.
Pilot holes are not provided, the screws
are self drilling. Do not tighten.
A C
E
KOptional
Q
R
E
E
Q
K
3”
A C
E F
A
L
E
F
L
Detail A

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 6 of 10
Step 3
• Attach the other wire management (L) to
leg (Q) same way as the previous step.
• Insert machine screws and washers through
the slots of both wire management and
into any two cage nuts. Do not tighten.
Note: If your table comes with
cross supports for added stability,
please refer to those instruction
for the next step.
Step 4
A B C
F G H
B
L
E
Q
F
G
H
Cage Nuts
Detail B
• Fully tighten all screws and bolts.
• Install the switch, cable clamps,
power strip, and control box. Pilot
holes are provided only for the
control box and switch.
A B C
E I J
K&A Manufacturing • 800.298.4351
J
E
E
J J
Table will NOT operate unless the
control box is screwed tight into
the table without any play.

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 7 of 10
Step 5
For the safety of the user and the workstation; the control box contains an internal sensor that is
sensitive to movement, vibration, and collision. For faultless operation, ensure all cables, electronics,
and accessories are cable managed and secured. Excessive load or weight must be distributed evenly.
Failure to follow these guidelines may cause intermittent functionality.
Caution:
Power
Cord Control Box
End View
Motor
Cable
Switch
Cord
Motor Cable
Motor
Cable
Motor
Cable
Power
Cord
Motor
Cable
Power
Cord
Motor
Cable
Switch
Cable

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 8 of 10
Save for Reference
Standard Switch
Start Up Procedure:
• Plug the power cord into a standard 110V receptacle. A power surge protector
is recommended.
• Press the down arrow until the worksurface reaches its lowest position.
• The workstation is ready for use.
• If the table is not functioning normally or has lost power, perform the reset procedure.
Reset Procedure:
• Unplug the unit from the wall for 10 seconds.
• Clear all obstructions from the travel path of the desk.
• Plug the unit back in the wall.
• Press and hold the down arrow key until the table reaches its lowest position.
Add Container Stops:
• Move the table to the upper or lower desired height.
• Rapidly press 4 times. You will hear a musical tone.
• Rapidly press 2 times. A musical tone plays two times.
- To add the upper container stop press A musical tone plays two times.
- To add the lower container stop press A musical tone plays two times.
Remove Container Stops:
• Move the table to the upper or lower preset height.
• Rapidly press 4 times. You will hear a musical tone.
• Rapidly press 2 times. A musical tone plays two times.
- To delete the upper container stop press You will hear a musical tone.
- To delete the lower container stop press You will hear a musical tone.
Troubleshooting:
If you are having any problems with the operation, contact RightAngle Products at 800.298.4351
or [e-mail]

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 9 of 10
Start Up Procedure:
• Plug the power cord into a standard 110V receptacle. A power surge protector
is recommended.
• Press the down arrow until the worksurface reaches its lowest position.
• The workstation is ready for use.
• If the table is not functioning normally, or has lost power,
perform the reset procedure.
Reset Procedure:
• Unplug the unit from the wall for 10 seconds.
• Clear all obstructions from the travel path of the desk.
• Plug the unit back in the wall.
• Press and hold the down arrow key until the table reaches its lowest position
See Packaged Instructions for Programmable Options
Optional Programmable Switch (full instructions packaged with switch)

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 10 of 10
If the table is unresponsive, uneven, or not functioning properly, perform a manual reset.
User settings are not reset in this process.
There are three methods to reset a workstation:
Reset Method A
1. Clear all obstructions from the travel path of the workstation
2. Disconnect the power to the control box for 30 seconds.
3. Reconnect the power
4. Press and hold the until the workstation has reached its lowest possible position.
Reset Method B (4 button programmable switch required)
1. Clear all obstructions from the travel path of the workstation
2. Quickly press UP + UP + UP + UP to enter the menu mode.
3. P01 is displayed and you will hear a musical tone.
4. Press the to navigate the menu.
5. Navigate to the P09 display
6. Press the button to enter or accept
7. Press and hold the until the workstation has reached its lowest possible position.
The workstation is now ready to operate
Reset Method C - 2 Button Switch
1. Clear all obstructions from the travel path of the workstation
2. Quickly press UP + UP + UP + UP to enter the menu mode.
3. You will hear a musical tone.
4. Press UP + UP + UP +
5. You will reach the limit adjustment menu and hear four musical tones.
6. Press and hold the until the workstation has reached its lowest possible position.
The reference is re-calibrated, the table should be leveled and the height indication should be correct.
Mechanical Reset Mode