RIGHT ANGLE NewHeights ELECTRIC HEIGHT ADJUSTABLE... User manual

6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
VERSION DATED: 10/30/14
K&A MANUFACTURING
M2
PAGE 1 OF 2
THE HOOKS MUST LOCK ONTO THE TABS AT THE CORD CONNECTION. FOLLOW THE RESET PROCEDURES ON PAGE 2.
M1
ARE VISIBLE.
STEP 7:
WIRING DIAGRAM
LH
COLUMN
RE-CONNECT THE CORDS TO THE CONTROL BOX AND THE CORD TAILS COMING OUT OF THE COLUMNS.
INSTRUCTIONS TO REPLACE CORDS ON NewHeights WORKSTATIONS:
STEP 1: UNPLUG THE POWER CORD FOR THE CONTROL BOX.
STEP 2: DISCONNECT THE LEFT AND RIGHT HAND COLUMN CORDS FROM THE CONTROL BOX.
STEP 3:DISCONNECT THE CORDS FROM THE SHORT CORD TAILS COMING OUT OF THE RIGHT AND LEFT HAND
COLUMNS.
STEP 4: DISCONNECT THE CORD FRON THE CENTER LEG IF YOU HAVE A 3-LEG WORKSTATION.
STEP 5: REMOVE THE OLD CORDS FROM THE WIRE MANAGEMENT J-CHANNELS OR U-CHANNEL.
STEP 6: RUN THE NEW CORDS THROUGH THE WIRE MANAGEMENT COMPONENTS. PLACE THE EXCESS CORD IN
THE WIRE MANAGEMENT,
NOTE CROSS SUPPORT NOT SHOWN
ON THIS VIEW SO OTHER COMPONENTS
M3
BOTTOM VIEW OF WIRE RUNS
THIS END GOES
COLUMN
RH
LEFT COLUMN WIRE
RIGHT COLUMN WIRE
HAND SWITCH WIRE
HAND SWITCH
DISCONNECTDISCONNECT
TO CONTROL BOX
HS
INSTRUCTION # 3088
TO COLUMNS
THIS END GOES
THIS SMALL TAB MUST GO UNDER
THE LOCK ON THE MOTOR CORD
SWITCH
HAND
CENTER
COLUMN
(3-LEG)

PAGE 2 OF 2
NewHeights™ ELECTRIC HEIGHT ADJUSTABLE WORKSTATION OPERATION INSTRUCTIONS:
CAUTION! TO PREVENT PINCHING OR COLLISION, MAKE SURE THAT YOU, YOUR FINGERS,
AND OTHER O JECTS ARE AT LEAST 3/4" FROM THE TA LE'S EDGES AND TRAVEL PATH.
STARTUP/RESET PROCEDURE:
STEP 1: PLUG THE POWER CORD FROM THE CONTROL BOX INTO A STANDARD 110 VOLT
RECEPTACLE. A POWER SURGE PROTECTOR IS RECOMMENDED.
STEP 2: PUSH THE DOWN ARROW UNTIL THE WORKSURFACE BOTTOMS OUT. THE NewHeights™
WORKSTATION IS NOW READY FOR USE.
TROUBLESHOOTING
IF YOU ARE HAVING ANY PROBLEMS WITH THE TABLE OPERATION, CONTACT RIGHTANGLE™
SERVICE AT 800-298-4351 OR [email protected].
WARRANTY INFORMATION:
NewHeights™ PRODUCTS ARE WARRANTED TO BE FREE OF DEFECTS DUE TO
MANUFACTURING OR MATERIALS AS FOLLOWS 2 YEARS ON THE GEAR AND/OR MOTOR,
INCLUDING THE CONTROL BOX AND HAND SWITCH. 5 YEARS ON THE SUPPORT BRACKETS,
ALUMINUM COLUMNS AND FEET. WE WILL REPLACE ANY DEFECTIVE PART AFTER
INSPECTION BY AN AUTHORIZED AGENT. COSTS INCURRED DUE TO PRODUCT
REPLACEMENT SUCH AS INSTALLATION, LABOR CHARGES OR TRANSPORTATION ARE NOT
COVERED UNDER THIS WARRANTY. WHEN CORRESPONDING WITH RIGHTANGLE™
PRODUCTS, RECORD AND PROVIDE THE MODEL AND SERIAL NUMBERS LOCATED ON THE
BACK PORTION OF THE RIGHT HAND COLUMN ASSEMBLY. SEE THE DETAIL BELOW.
SPECIAL NOTE: DO NOT USE ANY ABRASIVE CLEANERS ON THIS UNIT.
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
Monday−Friday 8:00 AM to 4:30 PM (Central)
.raproducts.com
VERSION DATED: 10/30/14
K&A MANUFACTURING
HAND SWITCH
SERIAL AND MODEL
NUMBERS ON
STICKERS OR CONTROL BOX
BACK OF RIGHT HAND COLUMN ASSEMBLY