RIGHT ANGLE NewHeights Series User manual

Instruction #53911 • Dated: 02/6/2018
NewHeights™ Series 4 Bonita ET 2-Leg Workstation
Warranty: raproducts.com/warranty
Failure to comply with or observe all assembly, safety, and operation instructions
and warnings regarding use of this product may result in serious property damage
or bodily injury.
Make sure no obstacles are in the desk’s path and all cords are of appropriate length for the
desk. Always maintain a 1” clearance around the table to prevent pinching.
Never assemble (or disassemble) the table or components with the table plugged into a pow-
er outlet. This product is for use on a nominal 120-volt circuit and has a grounding plug. Make
sure that the product is connected to an outlet having the same conguration as the plug. No
adapter should be used with this product.
1 of 8

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 2 of 8
E. 3/4” Wood Screw x42
F. 1/4”x5/8” Bolt x2
G. Lock Washer x2
H. 3/4” Wood Screw x4
I. Cord Clip x1
J. M6X10mm Bolt x4
K. Star Washer x4
L. Wire Management Channel x2
M. 3/16” Allen Wrench x1
N. 4mm Allen Wrench x1
O. 6mm Hex Rod Wrench x1
Left Leg Right Leg
Note
location
of drive
input hole.
Left leg has nuts
for motor mount.
Legs must be in
their lowest position
before installation.
Tools Required for Assembly
A. Power Driver with Adjustable Torque
B. Tape Measure
C. #2 Phillips Head Driver Bit
D. #2 Square Head Drive Bit (Recommended)
A B C D
Hardware and Tools Included for Assembly (may have extra)
E F G H I
J K L
M N 0
Bonita Parts
P. Cross Support x1
Q. U-Channel x1
R. Long Hex Rod x1
S. Switch x1
T. Control Box x1
U. Power Cord x1
V. Motor x1
W. Left Leg x1
X. Right Leg x1
Y. J-Channel x2
P Q R S
T U V
W
Y
X

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 3 of 8
Step 1
• Lay the worksurface on a protected
surface with pilot holes facing up.
• Insert hex rod through motor assembly and into
left leg drive input hole.
• If hex rod in the motor is not aligned properly
with drive input, turn hex rod clockwise 1/6th
or 1/3rd of a turn using the motor.
• Hex rod should slide into leg.
Legs must be in
lowest position
before installing
hex rod.
Motor
Assembly
Hex
rod
W
V
R
Step 2
• Align hex rod with right leg drive input.
• Turn hex rod counter clockwise 1/6th or
1/3rd of a turn with adjustable wrench, if
it is not aligned properly with drive input.
• Slide hex rod into leg and align pre-drilled
holes in worksurface.
X
V
R
W
O
Important: Please be aware that ¾” screws are
provided. If your worksurface is ¾” or thinner, you
will need to supply your own hardware.
O

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 4 of 8
F
G
Step 3
• Tighten motor mounting bolts after
hex rod is installed.
F G
M
Step 4
• Install u-channel.
AE
E
D
Q
Tip: For proper alignment of
pre-drilled holes, start screws
but do not fully tighten until
all are installed.

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 5 of 8
Step 5
• Slide cross support over leg
cross support brackets.
Step 6
• Install bolts and do not fully tighten.
P
J K
JK
J
JK
N

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 6 of 8
Step 7
• Install wood screws and tighten.
Step 9
E
AE
Snap switch on
control box
Note:
if you have
a programmable
switch (shown), please refer
to the installation instructions
included the switch.
Programmable
Switch
S
T
Step 8
• Fully tighten bolts
in cross support.
Tighten bolts

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 7 of 8
Step 10
Power Cable
Control Box End View
J-Channel
Wire Management
Motor Cable
Route to J-Channel
then Control Box
Power Cable
Route over U-Channel
Cable Routing Diagram
Use J-channel to Hold Extra Lengths of Cable
Motor Cable
Switch Cable
(Not in use with snap on switch)
Step 11
T
H
• Install wire management J-channel
and control box.
J-channels
A H
Y
E
E
Note: if you have a
programmable switch,
please refer to the
installation instructions
included the switch.

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 8 of 8
Save for Reference
If the leg assemblies are at uneven heights, it is usually caused by an improperly installed hex rod. Disassemble one
of the leg assemblies from the worksurface and make sure both ends of the hex rod are properly engaged in the hex
drives near the top of the leg assemblies.
Standard Switch
Note
Start Up:
• Plug the power cord into a standard 110v receptacle. A power surge protector
is recommended.
• Press the down arrow until the worksurface reaches its lowest position and the
control box clicks several times.
• The workstation is ready for use.
• If the table is not functioning normally, or has lost power, perform the reset procedure.
Reset Procedure:
Soft reset:
• Unplug the power for 30 seconds and plug back in.
• Hold the down arrow until the worksurface stops at the bottom and the control box clicks several times.
• If experiencing further issues, repeat reset procedure and then perform a hard reset.
Hard reset:
• Press and hold the down arrow button for 10 seconds until the control box clicks several times.
Troubleshooting:
If you are having any problems with the operation, contact RightAngle Products at 800.298.4351
or [e-mail].
Start Up:
• Plug the power cord into a standard 110v receptacle. A power surge protector
is recommended.
• Press the down arrow until the worksurface reaches its lowest position and the
control box clicks several times.
• The workstation is ready for use.
• If the table is not functioning normally, or has lost power, perform the
reset procedure.
Operation:
• To store a position, raise or lower the desk to the desired position. Press the save key. The display will read S. Press
the desired memory key 1-4. The display will read S 1, S 2, S 3 or S 4. You will hear a double click and the saved
desk height will be displayed. You can store up to four (4) positions.
• To recall a stored position, press and hold the memory key for the position you desire until the desk reaches that
position and stops. The height will be displayed. Do not press any other memory keys while the desk is in motion.
• See Packaged Instructions for Container and Shelf-Stop Positions
Optional Programmable Switch (full instructions packaged with switch)