6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: 800.298.4351 FAX: 866.882.9475
.raproducts.com
K&A MANUFACTURING
ON THE WORKSURFACE AS SHOWN. ALIGN THE HOLES IN THE
7/32" HEX HEAD DRIVER BIT OR
16
#2 SQUARE HEAD DRIVER BIT
WITH THE HELP OF AN ASSISTANT, PLACE 4) STAR WASHERS
ON A PROTECTED SURFACE WITH THE
WORKSURFACE SUPPORTS WITH THE PILOT HOLES IN THE WORKSURFACE.
SUPPORT SHOULD BE ATTACHED RESTING ON THE FEET OF THE COLUMN
THE MOTOR WIRES MUST FACE THE INSIDE OF THE WORKSTATION.
STEP 2:
LEVEL
4
SPECIAL EXCEPTION: ON WORKSTATIONS
INTO EACH END OF THE CROSS SUPPORT
AT 4" ABOVE THE BOTTOM OF THE
TOOLS REQUIRED FOR ASSEMBLY:
WORKSURFACE SUPPORTS AND FULLY TIGHTEN ALL THE SOCKET SCREWS
CORDLESS DRILL
#2 PHILLIPS HEAD DRIVER BIT OR
VERSION DATED: 5/10/13
PAGE 1 OF 3
PILOT HOLES FACING UP. PLACE THE LEFT HAND COLUMN ASSEMBLY
10
9
.INSERT AN END CAP
ON
4) SOCKET SCREWS
INSTRUCTION # 52 8
INSERT 2) SHORTY PLUGS
10
THE RIGHT HAND COLUMN ASSEMBLY
. INSERT THESE THROUGH THE HOLES AT THE ENDS
AND 15
11
3
OF THE CROSS SUPPORT
TAPE MEASURE
16
2
. PLACE 2) LOCK WASHERS
INTO THE ACCESS HOLES AT THE CENTER OF
,
14
HARDWARE PACK #
THE CROSS SUPPPORT.
ON 2) LOW
HEAD SOCKET SCREWS
STEP 4:
15
ASSEMBLIES TO ALLOW FOR CLEARANCE OF THE EQUIPMENT.
, AND THE CENTER COLUMN
. INSERT THESE THROUGH THE HOLES AT THE
CENTER OF THE CROSS SUPPORT. THREAD ALL 6) SOCKETSCREWS INTO
ON WHICH THE LifeBalan e™ STATION IS BEING INSTALLED, THE CROSS
5
THE HOLES IN THE T-SLOT PLATES THAT ARE PRE-INSTALLED IN THE SLOTS IN
THE COLUMNS. SEE DETAIL A. DO NOT FULLY TIGHTEN.
. SEE THE DETAIL AT LEFT.
STEP 3:
ASSEMBLY
ALLEN WRENCH PROVIDED
16
3/16" HEX HEAD DRIVER BIT
LEVEL THE CROSS SUPPORT
NewHeights™ RECTANGULAR 3-LEG WORKSTATION ASSEMBLY INSTRUCTIONS:
STEP 1: LAY THE WORKSURFACE 1
ITEM # PART # DESCRIPTION QTY.
1 VARIES WORKSURFACE 1
2 VARIES NewHeights LEFT HAND COLUMN ASSY 1
3 VARIES NewHeights RIGHT HAND COLUMN ASSY 1
4 VARIES NewHeights CENTER COLUMN ASSY 1
5 800411 NewHeights/HOVER END CAP 2
6 50285 NewHeights HAND SWITCH 1
7 51951 WIRE MANAGEMENT J 3
8 51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW 29
9 52477 3/8 INTERIOR TOOTH STAR WASHER 4
10 52470 3/8-16 x 3/8 BUTTON HEAD SOCKET SCREW 4
11 52059 5/8" SHORTY PLUG 2
12 50298 NewHeights CONTROL BOX 1
13 52498 7/32" ALLEN WRENCH 1
14 52425 3/8 x 1/2 x 1/8 HIGH COLLAR LOCK WASHER 2
15 52424 3/8-16 X 1/2 LOW HEAD SOCKET SCREW 2
16 800532 NewHeights 96" CROSS SUPPORT RECTANGULAR
3-LEG 91" ACTUAL) 1
15
14
9
1
2
4
3
16
WORKSURFACE SUPPORT
STEPS 1-4
11
5
10
DETAIL A
T-SLOT PLATE
PRE-INSTALLED
LOCATING THE CROSS SUPPORT
(SEE EXCEPTION IN STEP 3)
16
4.00
