RIGHT ANGLE NewHeights SPLIT WORKSURFACE ELECTRIC HEIGHT ADJUSTABLE... User manual

DETAIL A
PRE-INSTALLED
T-SLOT PLATE
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
MOTOR
STEPS 1-5
8
WIRES
SUPPORT
2
3
1
4
756 HARDWARE PACK # 52226
WORKSURFACE
FOOT
HARDWARE QUANTITIES MAY VARY
LEVEL
AND THE RI HT HAND
COLUMN ASSEMBLY 3
STEP 3:
ON THE WORKSURFACE 1 AS SHOWN. THE MOTOR
WIRES MUST FACE THE INSIDE OF THE WORKSTATION. ALI N THE HOLES IN THE
WORKSURFACE SUPPORTS WITH THE PILOT HOLES IN THE WORKSURFACE.
TOOLS REQUIRED FOR ASSEMBLY:
#2 SQUARE HEAD DRIVER BIT
INSTRUCTION # 5259
4mm HEX HEAD DRIVER BIT OR
ALLEN WRENCH PROVIDED
TAPE MEASURE
TI HTEN THE SCREWS. USE A LOW TORQUE SETTIN ON THE DRILL.
PA E 1 OF 3
CORDLESS DRILL
. DO NOT OVER-
#2 PHILLIPS HEAD DRIVER BIT OR
WITH THE HELP OF AN ASSISTANT, PLACE (4) STAR WASHERS
5
TO THE WORKSURFACE USIN (16) WOOD SCREWS
ON (4)
SOCKET SCREWS 6 . INSERT THESE THROU H THE HOLES AT THE ENDS OF THE
CROSS SUPPORT
. ATTACH THE WORKSURFACE SUPPORTS
4 AND THREAD THEM INTO THE T-SLOT PLATES THAT ARE PRE-
INSTALLED IN THE SLOTS IN THE COLUMN ASSEMBLIES
2
1
AND 3
THE CROSS SUPPORT.
. SEE DETAIL A
AT LEFT. DO NOT FULLY TI HTEN.
HOLES IN THE WORKSURFACE
STEP 4:
ALI N THE HOLES IN THE WORKSURFACE SUPPORTS WITH THE PILOT
LEVEL THE CROSS SUPPORT 4 AT 4" FROM THE BOTTOM OF THE WORK-
SURFACE SUPPORT AND FULLY TI HTEN THE SOCKET SCREWS
INTO THE ENDS OF
6 . SEE THE
STEP 5:
DETAIL AT LEFT. SPECIAL EXCEPTION: ON WORKSTATIONS ON WHICH THE
LifeBalance STATION IS BEING INSTALLED, THE CROSS SUPPORT SHOULD BE
INSTALLED RESTING ON THE FEET OF THE COLUMN ASSEMBLIES TO ALLOW FOR
CLEARANCE OF THE E UIPMENT. INSERT (2) END CAPS 7
NewHeights SPLIT WORKSURFACE ELECTRIC HEIGHT ADJUSTABLE WORKSTATION
ASSEMBLY INSTRUCTIONS:
STEP 1: LAY THE FIXED WORKSURFACE 1 ON A PROTECTED SURFACE WITH
THE PILOT HOLES FACIN UP.
STEP 2: PLACE THE LEFT HAND COLUMN ASSEMBLY 2
ITEM # PART # DESCRIPTION QTY.
1 VARIES NewHeights FIXED WORKSURFACE 1
2 VARIES NewHeights LEFT HAND COLUMN ASSEMBLY 1
3 VARIES NewHeights RI HT HAND COLUMN ASSEMBLY 1
4 VARIES NewHeights CROSS SUPPORT 1
5 52477 3/8 INTERIOR TOOTH STAR WASHER 4
6 52470 3/8-16 x 3/8 BUTTON HEAD SOCKET SCREW 4
7 800411 NewHeights/HOVER END CAP 2
8 51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW 19
9 VARIES NewHeights MOVABLE WORKSURFACE 1
10 50219 NewHeights SWIN ARM (300SW) 1
11 50072 8 x 3/4 PHILLIPS PAN HEAD RECEX DRIVE SCREW 4
12 51951 WIRE MANA EMENT J 3
13 50298 NewHeights CONTROL BOX 1
14 50285 NewHeights HAND SWITCH 1
15 52498 7/32" ALLEN WRENCH 1
VERSION DATED: 7/1 /12
LOCATING THE CROSS SUPPORT
(SEE EXCEPTION IN STEP 4)
BOTTOM OF
WORKSURFACE
SUPPORT
4.00

10
STEP 6
TURN THE BOLTS AT THE TOP OF THE CASTERS CLOCKWISE TO LEVEL THE UNIT.
(FROM THE TOP) ON THE LOW CORNERS OF THE UNIT. IF YOUR WORKSTATION HAS CASTERS,
LOCATION. LEVEL THE WORKSTATION BY TURNIN THE LEVELIN LIDES CLOCKWISE
WITH THE HELP OF AN ASSISTANT, SET THE WORKSTATION UPRI HT IN ITS FINAL
9
STEP 11:
CROSS SUPPORTS ARE
NOT SHOWN ON THESE
VIEWS SO OTHER COM-
PONENTS ARE VISIBLE.
8
STEPS 7-9
LEVELIN LIDE
OR CASTER
9
13
12
14
11
11
1
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
VERSION DATED: 7/18/12
K&A MANUFACTURING
PA E 2 OF 3
SWITCH
AS SHOWN ON THE WIRIN DIA RAM BELOW.
STEP 6: PLACE THE MOVABLE WORKSURFACE 9 ON THE PROTECTED SURFACE IN FRONT OF THE FIXED
WORKSURFACE 1 KEEPIN A 1/2" SPACE BETWEEN THE WORKSURFACES. PLACE THE SWIN ARM
10 ON
THE WORKSURFACES AS HOWN. ALI N THE HOLES IN THE SWIN ARM AND RELEASE PADDLE WITH THE PILOT
HOLES IN THE WORKSURFACES. ATTACH THEM USIN THE INSTRUCTIONS THAT CAME WITH THE ARM. THE
SCREWS ARE INCLUDED WITH THE ARM.
STEP 7: ALI N THE HOLES IN THE HAND SWITCH 14 WITH THE PILOT HOLES IN THE MOVABLE WORKSURFACE 9 .
ATTACH THE SWITCH WITH (2) RECEX DRIVE SCREWS
11 .
STEP : ALI N THE HOLES IN THE CONTROL BOX 13 WITH THE PILOT HOLES IN THE FIXED WORKSURFACE 1 .
ATTACH THE CONTROL BOX WITH (2) RECEX DRIVE SCHOOLS 11 .
STEP 9: ATTACH (3) WIRE MANA EMENT J'S 12 IN THE LOCATIONS SHOWN USIN (3) WOOD SCREWS .
PILOT HOLES ARE NOT PROVIDED. ON 60" AND 72" WORKSTATIONS, THE (2) WIRE MANA EMENT J'S NEAR
THE BACK ARE REPLACED WITH A U-CHANNEL.
STEP 10: RUN THE WIRES THROU H THE WIRE MANA EMENT J'S 12 AS SHOWN ON THE WIRE RUNS DIA RAM
BELOW. IF YOUR WORKSTATION HAS A U-CHANNEL, RUN THE WIRES THROU H IT. PLU THE WIRES INTO THE
RECEPTACLES ON THE CONTROL BOX 13
RH COLUMN
SWITCH
WIRE RUNS
WIRE
RI HT COLUMN WIRE
HAND SWITCH WIRE
HAND
LEFT COLUMN
WIRE
STEP 10
LH COLUMN
WIRIN DIA RAM
HS M1 M2
13

6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
VERSION DATED: 7/18/12
K&A MANUFACTURING
PA E 3 OF 3
NewHeights ELECTRIC HEIGHT ADJUSTABLE SPLIT WORKSURFACE WORKSTATION OPERATION
INSTRUCTIONS:
CAUTION! TO PREVENT PINCHING OR COLLISION, MAKE SURE THAT YOU, YOUR FINGERS,
AND OTHER OBJECTS ARE AT LEAST 3/4" FROM THE TABLE'S EDGES AND TRAVEL PATH.
STARTUP/RESET PROCEDURE:
STEP 1: PLU THE POWER CORD FROM THE CONTROL BOX INTO A STANDARD 110 VOLT
RECEPTACLE.
STEP 2: TO SET THE WORKSTATION, PRESS AND HOLD THE DOWN BUTTON ON THE HAND
SWITCH UNTIL THE WORKSTATION STOPS AT ITS LOWEST POSITION. THE NewHeights WORK-
STATION IS NOW READY FOR USE.
SET THE MOVABLE WORKSURFACE TO THE DESIRED HEI HT AND AN LE USIN THE
INSTRUCTIONS THAT CAME WITH THE SWIN ARM. IF THE SWIN ARM COLLIDES WITH
THE CROSS SUPPORT, REMOVE THE END CAPS, LOOSEN THE SOCKETSCREWS, AND DROP
THE CROSS SUPPORT TO A HEI HT WHERE THE SWIN ARM CLEARS IT. RETI HTEN THE
SCREWS AND REPLACE THE END CAPS.
IF YOU ARE HAVIN ANY PROBLEMS WITH THE PREVIOUS STEPS, CONTACT RI HTAN LE
SERVICE AT THE NUMBER ABOVE LEFT OR in[email protected].
TROUBLESHOOTING:
IF THE WORKSTATION STOPS OPERATIN OR A POWER FAILURE OCCURS, UNPLU THE
POWER CORD FROM THE RECEPTACLE AND REPEAT STEP 1 AND STEP 2 ABOVE.
WARRANTY INFORMATION:
NewHeights PRODUCTS ARE WARRANTED TO BE FREE OF DEFECTS DUE TO
MANUFACTURIN OR MATERIALS AS FOLLOWS: 2 YEARS ON THE EAR AND/OR MOTOR,
INCLUDIN THE CONTROL BOX AND HAND SWITCH. 5 YEARS ON THE SUPPORT BRACKETS,
ALUMINUM COLUMNS AND FEET. WE WILL REPLACE ANY DEFECTIVE PART AFTER
INSPECTION BY AN AUTHORIZED A ENT. COSTS INCURRED DUE TO PRODUCT
REPLACEMENT SUCH AS INSTALLATION, LABOR CHAR ES OR TRANSPORTATION ARE NOT
COVERED UNDER THIS WARRANTY. WHEN CORRESPONDIN WITH RI HTAN LE
PRODUCTS, RECORD AND PROVIDE THE SERIAL NUMBER LOCATED ON THE BACK
PORTION OF THE RI HT HAND COLUMN ASSEMBLY. SEE THE DETAIL AT LEFT.
SPECIAL NOTE: DO NOT USE ANY ABRASIVE CLEANERS ON THIS UNIT.
SERIAL NUMBER
ON STICKER
BACK OF RIGHT HAND COLUMN ASSEMBLY