RIGHT ANGLE NewCrank SPLIT WORKSURFACE CRANK HEIGHT ADJUSTABLE... User manual

NewCrank SPLIT WORKSURFACE CRANK HEIGHT ADJUSTABLE WORKSTATION
HARDWARE PACK # 52226 PAGE 1 OF 2
SLIDING THE OTHER END OF
THE HEX ROD INTO THE HEX DRIVE ON THE COLUMN ASSEMBLY. YOU MAY
NEED TO TURN THE CRANK ON THE LEFT HAND COLUMN ASSEMBLY TO ALIGN
ERSION DATED: 3/6/12
1
STEP 2:
HARDWARE QUANTITIES MAY VARY
SURFACE.
COLUMN ASSEMBLY
THE HOLES IN THE WORKSURFACE SUPPORT WITH THE PILOT HOLES IN THE WORK-
THE INNER COLUMN MUST FACE THE CENTER OF THE WORKSTATION. ALIGN
PLACE THE LEFT HAND COLUMN ASSEMBLY
ON THE WORKSURFACE
AS SHOWN. THE HEX DRIVE AT THE TOP OF
LEVEL 2
INSERT THE END OF THE HEX ROD
TAPE MEASURE
4
ALLEN WRENCH PROVIDED
3
7/ 2" HEX HEAD DRIVER BIT OR
#2 SQUARE HEAD DRIVER BIT
INTO THE HEX DRIVE ON THE LEFT
#2 PHILLIPS HEAD DRIVER BIT OR
CORDLESS DRILL
(THE ASSEMBLY WITH THE
HAND COLUMN ASSEMBLY
CRANK) ON THE WORKSURFACE
TOOLS REQUIRED FOR ASSEMBLY:
ASSEMBLY INSTRUCTIONS:
2
1
STEP 1: LAY THE FIXED WORKSURFACE 1 ON A PROTECTED SURFACE WITH THE
PILOT HOLES FACING UP.
AS FAR AS IT WILL GO. PLACE THE RIGHT HAND
STEP 3:
THE HEX ROD WITH THE HEX DRIVE. ALIGN THE HOLES IN THE WORKSURFACE
SUPPORT WITH THE PILOT HOLES IN THE WORKSURFACE.
INSTRUCTION # 52639
ITEM # PART # DESCRIPTION QTY.
1 VARIES NewHeights FIXED WORKSURFACE 1
2 VARIES NewCrank LEFT HAND COLUMN ASSEMBLY 1
VARIES NewCrank RIGHT HAND COLUMN ASSEMBLY 1
4 VARIES NewCrank HEX ROD 1
5 VARIES NewHeights CROSS SUPPORT 1
6 52477 /8 INTERIOR TOOTH STAR WASHER 4
7 52470 /8-16 x /8 BUTTON HEAD SOCKET SCREW 4
8 800411 NewHeights/HOVER END CAP 2
9 51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW 16
10 50219 NewHeights SWING ARM ( 00SW) 1
11 VARIES NewHeights MOVABLE WORKSURFACE 1
12 52498 7/ 2" ALLEN WRENCH 1
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
HEX
DRIVE
SUPPORT
WORKSURFACE
STEPS 1-3
1
2
4
READ ALL THE INSTRUCTIONS BEFORE BEGINNING
DO NOT OPERATE THE UNIT UNTIL IT IS FULLY ASSEMBLED

8
OR CASTER
OR COUNTER-CLOCKWISE TO LOWER IT. FOLD
WORKSURFACE TO THE DESIRED HEIGHT AND ANGLE.
THE CRANK HANDLE BACK UNDER THE FIXED WORKSURFACE. ADJUST THE MOVABLE
6
5
9
WORKSURFACE
7
SUPPORT
STEP 8: WITH THE HELP OF AN ASSISTANT, SET THE WORKSTATION UPRIGHT IN ITS
FINAL LOCATION. LEVEL THE WORKSTATION IF REQUIRED BY TURNING THE LEVELING
GLIDES CLOCKWISE (FROM THE TOP) ON THE LOW CORNERS OF THE UNIT. IF YOUR
WORKSTATION HAS CASTERS, TURN THE BOLTS AT THE TOP OF THE CASTERS CLOCK-
WISE TO LEVEL THE UNIT.
TO OPERATE: DROP THE MOVABLE WORKSURFACE 11 USING THE INSTRUCTIONS
THAT CAME WITH THE SWING ARM 10 . UNFOLD THE CRANK. TURN IT CLOCKWISE
TO RAISE THE FIXED WORKSURFACE 1
LEVELING GLIDE
FOOT
DETAIL A
PRE-INSTALLED
T-SLOT PLATE
STEPS 4-6
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
VERSION DATED: 3/6/12
K&A MANUFACTURING
PAGE 2 OF 2
STEP 4: WITH THE HELP OF AN ASSISTANT, PLACE (4) STAR WASHERS
6 ON (4) SOCKET SCREWS 7 . INSERT
THESE THROUGH THE HOLES AT THE ENDS OF THE CROSS SUPPORT 5 AND THREAD THEM INTO THE T-SLOT
PLATE THAT IS PRE-INSTALLED IN THE SLOT IN THE COLUMN ASSEMBLIES
2 AND 3 . SEE DETAIL A BELOW.
DO NOT FULLY TIGHTEN.
STEP 5: LEVEL THE CROSS SUPPORT 5 AT 4" FROM THE BOTTOM OF THE WORKSURFACE SUPPORT AND FULLY
TIGHTEN THE SOCKET SCREWS 7 . SEE THE DETAIL BELOW. SPECIAL EXCEPTION: ON WORKSTATIONS ON WHICH
THE LifeBalance STATION IS BEING INSTALLED, THE CROSS SUPPORT SHOULD BE INSTALLED RESTING ON THE FEET
OF THE COLUMN ASSEMBLIES TO ALLOW FOR CLEARANCE OF THE E UIPMENT.
STEP 6: ALIGN THE HOLES IN THE WORKSURFACE SUPPORTS WITH THE PILOT HOLES IN THE WORKSURFACE
1 .
ATTACH THE WORKSURFACE SUPPORTS TO THE WORKSURFACE USING (16) WOOD SCREWS
9 . DO NOT OVER-
TIGHTEN THE SCREWS. USE A LOW TORQUE SETTING ON THE DRILL.
STEP 7: PLACE THE MOVABLE WORKSURFACE 11 ON THE PROTECTED SURFACE IN FRONT OF THE FIXED WORK-
SURFACE 1 KEEPING A 1/2" SPACE BETWEEN THE WORKSURFACES. PLACE THE SWING ARM
10 ON THE WORK-
SURFACES. ALIGN THE HOLES IN THE SWING ARM AND RELEASE PADDLE WITH THE PILOT HOLES IN THE WORK-
SURFACES. ATTACH THE SWING ARM USING THE INSTRUCTIONS THAT CAME WITH THE ARM. THE SCREWS ARE
INCLUDED WTH THE ARM.
(SEE EXCEPTION IN STEP 5)
LOCATING THE CROSS SUPPORT
5
BOTTOM OF
WORKSURFACE
SUPPORT
4.00
11
10
STEP 7