Rightline Gear 100S30 User manual

2-Clean the vehicle’s roof of all dirt and debris.
3-Unzip the carrier completely and place it on top of the
vehicle with its non-zippered end facing front.
WARNING: DAMAGE MAY OCCUR TO THE CARRIER
IF EXCESS MATERIAL FLAPS IN THE WIND.
TO ELIMINATE EXCESS MATERIAL, PACK THE CARRIER
FULL. IF UNABLE TO PACK FULL, FILL THE ENCLOSED
SPACE OF THE CARRIER AND PULL THE EXCESS
MATERIAL DOWN OVER THE SIDES. HOLD THE EXCESS
MATERIAL SECURELY IN PLACE WITH THE CARRIER’S
STRAPS.
4-Start by completely lling the enclosed space in the front
part of the carrier with your gear (Fig 2). Continue loading
the rear of the carrier. Place sharp edged items in the
middle and softer items around them.
1-Remove the Car Clips from the (4) attachment straps (Fig
4); the Car Clips will not be used.
Pack The Carrier
Attach The Carrier - WITH A Roof Rack
The correct attachment of this product is critical and
beyond the control of Rightline Gear. The safe use
and long life of this product depends entirely on
your good judgment and following these directions.
2-Decide if you will be attaching the straps to the roof
rack side rails or cross bars. If side rails, the straps will
connect to the side buckles (Fig 5). If cross bars, the straps
will connect to the front and rear buckles (Fig 5).
Sport Car Top Carriers 100S30, 100S20, 100S50
1-Apply a small amount of the included lubricant to the
outer surface of the zipper (Fig 1). Run the zipper head
over the lubricant and around the carrier several times to
ensure proper lubrication.
WARNING: FOR THE CARRIER TO BE 100% WATER-
PROOF, THE NON-ZIPPERED END MUST BE FACING
THE FRONT OF THE VEHICLE, THE (2) ZIPPER HEADS
MUST BE LOCATED IN THE CENTER OF THE REAR
PROTECTOR, AND THE HOOK-&-LOOP CLOSURE ON
THE PROTECTOR MUST BE SECURED.
NOTE: REQUIRES SPACE UNDER THE ROOF RACK
SIDE RAILS OR CROSS BARS FOR THE CARRIER’S
ATTACHMENT STRAPS TO PASS THROUGH.
Fig 4
5-Close the zipper as you ll the carrier. Bring the (2) zip-
per heads together under the rear protector and secure
the hook-&-loop closure (Fig 3).
NOTE: THE LUBRICANT HELPS THE ZIPPER HEADS
EASILY SLIDE OVER THE OUTER RUBBER SURFACE
OF THE ZIPPER. PETROLEUM JELLY, WD-40, AND LIP
BALM CAN BE USED AS ALTERNATIVES. DO NOT
APPLY THE LUBRICANT ON THE ZIPPER TEETH.
Fig 1
Fig 2
Hook-&-Loop
Closures
Rear
Protector
Fig 3
Front
Enclosed Space
Zipper
End
Hook-&-Loop
Closures
Fig 5
Side
Buckles Rear
Buckles
Front
Buckles
Front
Side Rail
Side Rail
Cross
Bar
Cross
Bar
3-Attach each strap by wrapping it around the rack,
threading its end through its loop, and pulling tight (Fig 6).
4-Thread the straps up through slot A and down through
slot B of the buckles (Fig 7) and tighten the straps evenly.
5-Tie off the strap ends so they don’t ap in the wind (Fig
8). Make sure to re-tighten the straps after a few miles
and check them regularly throughout the trip.

Front
Fig 10
1-Start with the Car Clips on the (4) attachment straps (Fig 9).
5-Tighten the straps evenly (Fig 13 and Fig 14) and shut
the vehicle’s doors over the clips/straps (Fig 15).
Fig 14
Attach The Carrier - WITHOUT A Roof Rack
Fig 12
6-Tie off the strap ends so they don’t ap in the wind (Fig
16). Make sure to re-tighten the straps after a few miles
and check them regularly throughout the trip.
Fig 16
Fig 9
NOTE: IF A STRAP MAKES NOISE WHILE DRIVING,
LOOSEN THE STRAP, RE-POSITION IT SLIGHTLY,
AND RE-TIGHTEN IT.
3-Hold the straps with the Car Clips facing towards the
vehicle (Fig 11). Thread the straps up through slot A and
down through slot B of the buckles (Fig 7).
2-Line up the side buckles with the doors of the vehicle
(Fig 10). If a 4-door vehicle, (1) strap will attach to the
door frame weather molding in each of the (4) doors. If
a 2-door vehicle, (2) straps will attach to the door frame
weather molding in each of the (2) doors.
Side Buckles
Fig 6
AB
Fig 7Fig 8
NOTE: IF A STRAP MAKES NOISE WHILE DRIVING,
LOOSEN THE STRAP, RE-POSITION IT SLIGHTLY,
AND RE-TIGHTEN IT.
Fig 11
4-Open the vehicle’s doors and hook the Car Clips under
the door frame weather molding (Fig 12).
1-Run a strap’s loop through the backside of a Car Clip
(Fig 17).
Re-Connect The Car Clips To The Attachment Straps
2-Thread the strap’s end through its loop (Fig 18).
3-Pull the strap’s end to tighten the strap around the Car
Clip (Fig 19).
4-Repeat steps 1-3 for the other (3) straps.
Fig 18
Loop Strap End
Car Clip
Loop
Fig 13
Fig 15
Fig 17
Fig 19
Learn more about roof racks and cargo carriers we have.