Risco Agility RW132KL1P User manual

1
Wireless Slim Keypad
Model: RW132KL1P; RW132KL2P
Installation Instructions
1 General Description
The Wireless Slim keypad is used to remotely operate the WiComm Smart
Hub. The two-way keypad receives a reply status indication from the Smart
Hub for each command that it sends.
You can use a proximity tag or enter a code to operate and use the functions
of the keypad.
2 Installation
Step 1: Mounting Considerations
Mount the keypad near the entrance of the house to easily arm and disarm
your security sysytem on a daily basis. In additon, place the keypad that
ensures good communciation between the keypad and Smart Hub.
Step 2: Quick Device Allocation
The keypad must identify itself to the WiComm Smart Hub. This can be
performed either using the RISCO Express Wizard
(www.riscocloud.com/express) by adding the keypad at the time of the
Smart Hub system installation or later either by using the “Settings” on the
Web (www.riscocloud.com) or using the WiComm Smart Hub, as follows:
1. Press the button on the WiComm Smart Hub for 5 seconds; the unit
beeps once as it enters Learn mode (all the LEDs also light up, one after
the other).
2. Remove the red isolation strips to activate the batteries.
3. Send a signal transmission from the keypad by pressing and
simultaneously for at least 2 seconds; the Smart Hub beeps once
to accept or beeps three times to reject. Once accepted, the system
announces the device.
The WiComm Smart Hub beeps once to accept or beeps three times
to reject. Once accepted, the system announces the device type and
its zone (for example, “Detector, zone 1”).
4. To complete allocation, momentarily press the WiComm Smart Hub
button . A short beep is head and the LEDs stop flashing.
5. Mount the keypad
Note: For future use, it is recommended to write down the keypad
description, zone number, and installation location of each allocated keypad.
3 Installation
1. Remove the locking pin
securing the mounting
bracket to the unit.
2. Separate the mounting plate
from the keypad's main unit.
3. Mount the bracket to the wall
using the supplied screws.
4. Mount the keypad to the
bracket.
4 Buzzer and LED Indications
Buzzer Indications:
Duration Operation
Long beep Confirmation
3 short beeps Wrong code
Pulsed beeps Exit/enty beeps (programmable)
Short beep Each key press
LED Indciations:
Color State Status
Blue Blink During
communcation with
the panel
Red On System fully or
partially armed
Slow flash During Exit delay
Rapid
flash
During alarm
Green Blink Trouble indication in
the system while the
system is unset
Green/Red
toggle
Toggle Waiting for code to
be entered
5 Using the Proxmity Tag
The proximity tag, is
correctly used by applying it
within a 2 cm distance from
the key
as shown in the
illustration (after waking the
keypad by pressing the
appropriate key).
6 Common Operations
Common Operations
Operation Action
Away arming
Press
Stay / Home arming Press
Disarm
1. Press > Code or present Proximity tag
(after wakeup)
Advanced Operations
Operation Action
Partition 1/2/3 Arming
(Away)
Select partition 1/2/3 and press
Stay arm partition 1/2/3
Select partition 1/2/3 and press
Partition Disarm
Select partition 1/2/3 and press followed by Code
1
Blue Red Green

2
Operation Action
Panic alarm
Press buttons + simutaneously for 2 seconds
Fire alarm
Press buttons + simutaneously for 2 seconds
Emergency/Med. alarm
Press buttons + simutaneously for 2 seconds
System Chime On/Off
Press the button for 2 seconds
Main unit
speaker volume
Press the button for 2 seconds.
Select the volume level (0=No sound, 4= full volume)
Press to
save your selection
Set keypad exit/entry
beeps
Press the button for 2 seconds to toggle between
On/Off
Activate/Deactivate
light
sensor
3
Press the button for 2 seconds to toggle between
On/Off
Status request
Press the button for 2 seconds for system system
status
message
and view LED display
Ring local door bell
Press the button to activate a door bell sound on
the main system.
Wake up keypad Press
Notes:
1.
The proximity tag can be used instead of code.
2. For Part Setting (Stay Arming) with no entry delay press the key for two
seconds.
3.
Light sensor is used to save battery by turning on/off the keypad
backlight.
7 Replacing Batteries
1. Release the battery cover
screw and insert the supplied
two batteries. Pay attention
to polarity.
2. Close the battery
compartment.
CAUTION: Risk of explosion if
battery is replaced by an
incorrect type. Dispose of used
batteries according to local
regulations.
8 Technical Specifications
Battery type CR123, 3V lithium battery (x 2)
Current consumption 10µA stand by; 100 mA Max.
Battery life 3 years (for typical use)
Frequency 915MHz, 13.56MHz
Operating temperature -10° – 55°C (14° – 131°F)
Storage temperature -20° – 60°C (-4° – 140°F)
Dimensions 100 mm X 45 mm X 25 mm (3.9 x 1.8
x .98 inches)
Weight (incl batteries) 0.157 kg
Standard Limited Product Warranty (“Limited Warranty”)
RISCO Ltd. (“RISCO") guarantee RISCO’s hardware products (“Products”) to be free from
defects in materials and workmanship when used and stored under normal conditions and in
accordance with the instructions for use supplied by RISCO, for a period of (i) 24 months from the
date of delivery of the Product (the “Warranty Period”). This Limited Warranty covers the Product
only within the country where the Product was originally purchased and only covers Products
purchased as new.
Contact with customers only. This Limited Warranty is solely for the benefit of customers who
purchased the Products directly from RISCO or from an authorized distributor of RISCO. RISCO
does not warrant the Product to consumers and nothing in this Warranty obligates RISCO to
accept Product returns directly from end users who purchased the Products for their own use
from RISCO’s customer or from any installer of RISCO, or otherwise provide warranty or other
services to any such end user directly. RISCO’s authorized distributor or installer shall handle all
interactions with its end users in connection with this Limited Warranty. RISCO’s authorized
distributor or installer shall make no warranties, representations, guarantees or statements to its
end users or other third parties that suggest that RISCO has any warranty or service obligation to,
or any contractual privy with, any recipient of a Product.
Remedies. In the event that a material defect in a Product is discovered and reported to RISCO
during the Warranty Period, RISCO shall accept return of the defective Product in accordance
with the below RMA procedure and, at its option, either (i) repair or have repaired the defective
Product, or (ii) provide a replacement product to the customer.
Return Material Authorization. In the event that you need to return your Product for repair or
replacement, RISCO will provide you with a Return Merchandise Authorization Number (RMA#)
as well as return instructions. Do not return your Product without prior approval from RISCO. Any
Product returned without a valid, unique RMA# will be refused and returned to the sender at the
sender’s expense. The returned Product must be accompanied with a detailed description of the
defect discovered (“Defect Description”) and must otherwise follow RISCO’s then-current RMA
procedure published in RISCO’s website at www.riscogroup.com in connection with any such
return. If RISCO determines in its reasonable discretion that any Product returned by customer
conforms to the applicable warranty (“Non-Defective Product”), RISCO will notify the customer
of such determination and will return the applicable Product to customer at customer’s expense.
In addition, RISCO may propose and assess customer a charge for testing and examination of
Non-Defective Product.
Entire Liability. The repair or replacement of Products in accordance with this Limited Warranty
shall be RISCO’s entire liability and customer’s sole and exclusive remedy in case a material
defect in a Product is discovered and reported as required herein. RISCO’s obligation and this
Limited Warranty are contingent upon the full payment by customer for such Product and upon a
proven weekly testing and examination of the Product functionality.
Limitations. This Limited Warranty is the only warranty made by RISCO with respect to the
Products. The warranty is not transferable to any third party. To the maximum extent permitted by
applicable law, this Limited Warranty shall not apply and will be void if: (i) the conditions set forth
above are not met (including, but not limited to, full payment by customer for the Product and a
proven weekly testing and examination of the Product functionality); (ii) if the Products or any part
or component thereof: (a) have been subjected to improper operation or installation; (b) have
been subject to neglect, abuse, willful damage, abnormal working conditions, failure to follow
RISCO’s instructions (whether oral or in writing); (c) have been misused, altered, modified or
repaired without RISCO’s written approval or combined with, or installed on products, or
equipment of the customer or of any third party; (d) have been damaged by any factor beyond
RISCO’s reasonable control such as, but not limited to, power failure, electric power surges, or
unsuitable third party components and the interaction of software therewith or (e) any failure or
delay in the performance of the Product attributable to any means of communication provided by
any third party service provider, including, but not limited to, GSM interruptions, lack of or internet
outage and/or telephony failure. BATTERIES ARE EXPLICITLY EXCLUDED FROM THE
WARRANTY AND RISCO SHALL NOT BE HELD RESPONSIBLE OR LIABLE IN RELATION
THERETO, AND THE ONLY WARRANTY APPLICABLE THERETO, IF ANY, IS THE BATTERY
MANUFACTURER'S WARRANTY. RISCO does not install or integrate the Product in the end
user’s security system and is therefore not responsible for and cannot guarantee the performance
of the end user’s security system which uses the Product or which the Product is a component of.
This Limited Warranty applies only to Products manufactured by or for RISCO. Further, this
Limited Warranty does not apply to any software (including operating system) added to or
provided with the Products or any third-party software, even if packaged or sold with the RISCO
Product. Manufacturers, suppliers, or third parties other than RISCO may provide their own
warranties, but RISCO, to the extent permitted by law and except as otherwise specifically set
forth herein, provides its Products “AS IS”. Software and applications distributed or made
available by RISCO in conjunction with the Product (with or without the RISCO brand), including,
but not limited to system software, as well as P2P services or any other service made available
by RISCO in relation to the Product, are not covered under this Limited Warranty. Refer to the
Terms of Service at: https://riscocloud.com/ELAS/WebUI/UserLogin/License for details of your
rights and obligations with respect to the use of such applications, software or any service.
RISCO does not represent that the Product may not be compromised or circumvented; that the
Product will prevent any personal injury or property loss by burglary, robbery, fire or otherwise, or
that the Product will in all cases provide adequate warning or protection. A properly installed and
maintained alarm may only reduce the risk of a burglary, robbery or fire without warning, but it is
not insurance or a guarantee that such will not occur or will not cause or lead to personal injury or
property loss. CONSEQUENTLY, RISCO SHALL HAVE NO LIABILITY FOR ANY PERSONAL
INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING
A CLAIM THAT THE PRODUCT FAILED TO GIVE WARNING.
EXCEPT FOR THE WARRANTIES SET FORTH HEREIN, RISCO AND ITS LICENSORS
HEREBY DISCLAIM ALL EXPRESS, IMPLIED OR STATUTORY, REPRESENTATIONS,
WARRANTIES, GUARANTEES, AND CONDITIONS WITH REGARD TO THE PRODUCTS,
INCLUDING BUT NOT LIMITED TO ANY REPRESENTATIONS, WARRANTIES,
GUARANTEES, AND CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, TITLE AND WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS, TO THE
EXTENT PERMITTED BY LAW. WITHOUT LIMITING THE GENERALITY OF THE
FOREGOING, RISCO AND ITS LICENSORS DO NOT REPRESENT OR WARRANT THAT: (I)
THE OPERATION OR USE OF THE PRODUCT WILL BE TIMELY, SECURE,
UNINTERRUPTED OR ERROR-FREE; (ii) THAT ANY FILES, CONTENT OR INFORMATION OF
ANY KIND THAT MAY BE ACCESSED THROUGH THE PRODUCT SHALL REMAIN SECURED
OR NON DAMAGED. CUSTOMER ACKNOWLEDGES THAT NEITHER RISCO NOR ITS
LICENSORS CONTROL THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES,
INCLUDING THE INTERNET, GSM OR OTHER MEANS OF COMMUNICATIONS AND THAT
RISCO’S PRODUCTS, MAY BE SUBJECT TO LIMITATIONS, DELAYS, AND OTHER
PROBLEMS INHERENT IN THE USE OF SUCH MEANS OF COMMUNICATIONS. RISCO IS
NOT RESPONSIBLE FOR ANY DELAYS, DELIVERY FAILURES, OR OTHER DAMAGE
RESULTING FROM SUCH PROBLEMS. RISCO WARRANTS THAT ITS PRODUCTS DO NOT,
TO THE BEST OF ITS KNOWLEDGE, INFRINGE UPON ANY PATENT, COPYRIGHT,
TRADEMARK, TRADE SECRET OR OTHER INTELLECTUAL PROPERTY RIGHT IN ANY
EVENT RISCO SHALL NOT BE LIABLE FOR ANY AMOUNTS REPRESENTING LOST
REVENUES OR PROFITS, PUNITIVE DAMAGES, OR FOR ANY OTHER INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF THEY WERE FORESEEABLE OR
RISCO HAS BEEN INFORMED OF THEIR POTENTIAL.
WARNING: This product should be tested at least once a week.
FCC ID: JE4RW132KLXP1356
Contains FCC ID: JE4STAMP915
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment
FCC Note
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment on and off, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on to a different circuit from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment which are not expressly approved by the
party responsible for compliance (RISCO Group's.) could void the user's authority to
operate the equipment.
© RISCO Group 03/17 5IN2557