RiverRidge Ashland 06-088 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® Ashland Single Door Wall Cabinet
ITEM# 06-088 White
ITEM# 06-089 Gray
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS CABINET WILL HOLD UP TO 10 POUNDS PER SHELF OR A TOTAL OF 20 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 10 POUNDS. LOADING WITH MORE THAN
10 POUNDS PER SHELF MAY CAUSE DAMAGE TO THE CABINET OR CAUSE SERIOUS
INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Left Side Panel
3
1PC
Right Side Panel
4
1PC
Fixed Shelf
5
1PC
Rear Cross Bar
6
1PC
Bottom Board
7
1PC
Door
8
1PC
Back Board

TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [e-mail], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
NO
PARTS
QTY
DESCRIPTION
A
6PCS
Cam Bolt
B
6PCS
Cam Lock
C
16PCS
Wood Dowel
D
2PCS
Screw (3x14mm)
E
1PC
Magnet
F
10PCS
Screw (3x10mm)
G
2PCS
Metal Hinge
H
1PC
Magnet Plate
I
1PC
Machine Screw (4x20mm)
J
1PC
Knob
K
14PCS
Screw (2.5x12mm)
L
2PCS
Plastic Anchor
M
2PCS
Screw (4x45mm)
1PC
Wall Mounting Paper Template

STEP 1
1. Screw 1 cam bolt (A) into cam bolt hole on left side panel (2).
2. Screw 1 cam bolt (A) into cam bolt hole on right side panel (3).
3. Attach 2 metal hinges (G) to right side panel (3) by inserting 4 screws (F) through holes
on metal hinges (G), then tighten to right side panel (3).
STEP 2
1. Insert 4 wood dowels (C) into holes on ends of rear cross bar (5).
2. Insert 4 wood dowels (C) into holes on ends of shelf (4).
3. Attach left side panel (2) to rear cross bar (5) and fixed shelf (4) by inserting wood dowels
(C) into wood dowel holes and inserting 1 cam bolt (A) into cam lock hole.
4. Insert 1 cam lock (B) into cam lock hole on fixed shelf (4), then rotate clockwise to secure
cam bolt (A) in place.
5. Repeat above steps to assemble right side panel (3) to rear cross bar (5) and fixed shelf (4).

STEP 3
1. Screw 2 cam bolts (A) into cam bolt holes on bottom board (6).
2. Screw 2 cam bolts (A) into cam bolt holes on top board (1).
3. Attach 1 magnet (E) to top board (1) by inserting 2 screws (D) through holes on magnet (E),
then tighten to top board (1).
STEP 4
1. Insert 4 wood dowels (C) into wood dowel holes on the bottom board (6).
2. Attach bottom board (6) to pre-assembled unit by inserting wood dowels (C) into wood
dowel holes and inserting cam bolts (A) into cam lock holes on side panels (2) and (3).
3. Insert 2 cam locks (B) into cam lock holes on side panels (2) and (3), then rotate clockwise
to secure cam bolts (A) in place.
4. Repeat above steps to assemble top board (1) to pre-assembled unit.

STEP 5
1. Attach back board (8) to pre-assembled cabinet by inserting 14 screws (K) through holes
on back board (8), then tighten to back of cabinet.
STEP 6
1. Attach magnet plate (H) to door (7) by inserting 2 screws (F) through holes on magnet plate
(H), then tighten to door (7).
2. Attach knob (J) to door (7) by inserting 1 machine screw (I) through hole on door (7), then
tighten to knob (J).

STEP 7
1. Attach door (7) to right side panel (3) by inserting 4 screws (F) through holes on metal
hinges, then tighten to right side panel (3).
STEP 8
Option #1: Securing to Drywall
1. Using wall mounting paper template to determine position, screw 2 plastic anchors (L) into
drywall.
2. Insert 2 screws (M) through holes on inside of cabinet and into plastic anchors (L) and tighten.
Option #2: Securing to Drywall and Wood Stud
1. Insert 2 screws (M) through holes on inside of cabinet, then tighten through drywall and into
wood stud.

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016