RiverRidge Ellsworth Tall Corner Cabinet 06-027 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® Ellsworth Tall Corner Cabinet
ITEM#: 06-027 White
ITEM#: 06-028 Espresso
ITEM#: 06-127 Taupe
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 125 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 125 POUNDS TOTAL
WEIGHT. OVERLOADING MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS
INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Middle Connection Board
2
1PC
Left Lower Support Board
3
1PC
Right Lower Support Board
4
1PC
Lower Cross Bar
5
1PC
Right Side Door
6
1PC
Left Side Door
7
1PC
Adjustable Shelf
8
2PCS
Top & Bottom Fixed Shelf
9
1PC
Left Lower Side Panel
10
1PC
Right Lower Side Panel
11
1PC
Right Upper Support Board
12
1PC
Left Upper Support Board
13
1PC
Top Cross Board
14
1PC
Left Upper Side Panel
15
1PC
Right Upper Side Panel
16
2PCS
Top Open Shelf

PARTS LIST
NO
PARTS
QTY
DESCRIPTION
A
4PCS
Cam Bolt
B
4PCS
Cam Lock
C
24PCS
Wood Dowel
D
1PC
Magnet
E
2PCS
Screw (3x14mm)
F
18PCS
Screw (3x10mm)
G
4PCS
Hinge
H
2PCS
Magnet Plate
I
30PCS
Screw (4x25mm)
J
2PCS
Knob
K
2PCS
Machine Screw (4x18mm)
L
4PCS
Shelf Holder
M
4PCS
Screw (4x35mm)
N
2PCS
Long Wood Dowel
O
4PCS
Plastic Anchor
P
4PCS
Screw (4x45mm)
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [e-mail], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
1. Insert 1 wood screw (F) through hole in magnet plate (H) and tighten to right side door (5).
2. Insert 4 wood screws (F) through holes in 2 hinges (G) and tighten to right side door (5).
3. Repeat above steps to assemble magnet plate (H) and 2 hinges (G) to left side door (6).
STEP 2
1. Insert 4 wood dowels (C) into wood dowel holes on each end of lower cross bar (4).
2. Attach left lower support board (2) to lower cross bar (4) by inserting wood dowels into
wood dowel holes on left lower support board (2).
3. Attach right lower support board (3) to lower cross bar (4) by inserting wood dowels into
wood dowel holes on right lower support board (3).

STEP 3
1. Attach right side door (5) and left side door (6) to left lower support board (2) and right lower
support board (3) by inserting 8 wood screws (F) through holes in hinges (G) on right side
door (5) and left side door (6) and tighten to left lower support board (2) and right lower
support board (3).
STEP 4
1. Attach shelf (8) to both lower side support boards (2), (3) by inserting 2 wood screws (I)
through holes on shelf (8) and tighten to left lower support board (2) and right lower support
board (3). Do not overtighten.
2. Insert 2 wood dowels (C) into dowel holes on shelf (8).

STEP 5
1. Attach left lower side panel (9) to left lower support board (2) and shelf (8) by inserting
wooden dowel (C) into dowel hole in left lower side panel (9).
2. Insert 4 wood screws (I) through holes in left lower side panel (9) and tighten to shelf (8)
and left lower support board (2).
STEP 6
1. Attach right lower side panel (10) to shelf (8), right lower support board (3) and left
lower side panel (9) by inserting 7 screws (I) through holes on right lower side panel
(10) and tighten to shelf (8), right lower side support board (3) and left lower side
panel (9).

STEP 7
1. Screw 4 cam bolts (A) into cam bolt holes on middle connection board (1). Do not
overtighten.
2. Attach magnet (D) to middle connection board (1) by inserting 2 screws (E) through holes
on magnet (D) and tighten to middle connection board (1).
STEP 8
1. Insert 4 wood dowels (C) into wood dowel holes in end of top cross board (13).
2. Attach right upper support board (11) and left upper support board (12) to top cross board
(13) by inserting wood dowels into wood dowel holes on right upper support board (11)
and left upper support board (12).

STEP 9
1. Attach shelf (8) to both upper support boards (11) and (12) by inserting 2 screws (I)
through holes on shelf (8) and tighten to left upper support board (12) and right upper
support board (11). Do not overtighten.
2. Insert 2 wood dowels (C) into dowel holes on shelf (8).
STEP 10
1. Insert 2 wood dowels (C) into wood dowel holes on each shelf (16).
2. Attach 2 shelves (16) to left upper side panel (14) by inserting 2 wood dowels (C) into
wood dowel holes on left upper side panel (14) and inserting 2 wood screws (I)
through holes on left upper side panel (14) and tighten to shelf (16).

STEP 11
1. Attach left upper side panel (14) to shelves (16) and left upper support board (12) and
shelf (8) by inserting wood dowels (C) into wood dowel holes on inner side of left upper
side panel (14).
2. Insert 4 wood screws (I) through holes on left upper side panel (14) and tighten to shelf (8)
and left upper support board (12).
STEP 12
1. Insert 2 wood dowels (C) into wood dowel holes on shelves (16).

STEP 13
1. Attach right upper side panel (15) to left upper side panel (14), shelves (16) and shelf (8) by
inserting wood dowels (C) on shelves (16) and shelf (8) into wood dowel holes on inner
side of right upper side panel (15).
2. Insert 9 wood screws (I) through holes on right upper side panel (15) and tighten to shelf
(8), shelves (16), right upper support board (11) and left upper side panel (14).
STEP 14
1. Insert 4 wood dowels (C) into wood dowel holes on end of left upper side panel (14) and
right upper side panel (15).
2. Attach middle connection board (1) by inserting wooden dowels (C) into wood dowel holes
on middle connection board (1) and insert 4 long wood screws (M) through holes on
middle connection board (1) and tighten to left upper side panel (14) and right upper side
panel (15).

STEP 15
1. Insert 2 long wood dowels (N) and 4 wood dowels (C) into wood dowel holes on lower
support boards (2) and (3) and lower side panels (9) and (10).
2. Two people may be required for this step. Attach upper unit to lower unit by inserting
wooden dowels (C) and (N) into wood dowel holes on upper support boards (11) and (12)
and upper side panels (14) and (15) and inserting 4 cam bolts (A) into cam lock holes on
lower side panels (14) and (15).

STEP 16
1. Insert 4 cam locks (B) into cam lock holes on left lower side panel (9) and right lower side
panel (10) and rotate cam locks (B) clockwise to lock cam bolts.
2. Insert 4 adjustable shelf holders (L) into holes on left lower side panel (9) and right lower
side panel (10).
3. Insert 1 machine screw (K) through hole on left side door (6) and tighten to knob (J).
4. Repeat above step 3 to assemble knob to right door (5).

STEP 17
1. Place shelf (7) onto shelf holders (L).
Option #1: Securing to Drywall
1. Place cabinet against wall in desired location. Using a pencil, make 4 small marks on wall
through holes on side panels. Move cabinet away from wall and screw 4 plastic anchors (O)
into wall on pencil marks.
2. Place cabinet against wall, insert 4 screws (P) through holes on side panels, then tighten to
plastic anchors (O).
Option #2: Securing to Drywall and Wood Stud
1. Place cabinet against wall in desired location. Insert 4 screws (P) through holes on side
panels, then tighten through drywall and into wood stud.

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016