RiverRidge Afton 16-036 User manual

ITEM #:16-036
RiverRidge®Afton Metal Frame Hall Tree
ASSEMBLY INSTRUCTIONS
ADULT ASSEMBLY REQUIRED
WARNING
SEE FULL WARNING ON PAGE 2
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
Young children can be seriously injured or killed if furniture tips over.
Don’t use this item for a TV stand or place heavy objects on top of item.
Always use angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 15 POUNDS PER SHELF AND 5 POUNDS PER
HOOK FOR A TOTAL OF 45 POUNDS. BENCH SEATING WEIGHT CAPACITY IS 200
POUNDS. DO NOT LOAD SHELVES WITH MORE THAN 15 POUNDS, HOOKS WITH
MORE THAN 5 POUNDS OR SEATING WITH MORE THAN 200 POUNDS.
OVERLOADING WITH MORE THAN 15 POUNDS PER SHELF, 5 POUNDS PER HOOK
OR 200 POUNDS PER SEATING MAY CAUSE DAMAGED TO THE SHELF UNIT OR
SERIOUS INJURY OR DEATH.

1
8
8
2
3
9
9
10
10
11
11
6
6
4
5
7
7
7
Top Board1PC
QTY DESCRIPTION
Back Panel1PC
Shelf1PC
Lower Left Metal Side Frame
Lower Right Metal Side Frame
1PC
Upper Metal Side Frame
1PC
Bottom Metal Frame
2PCS
Metal Cross Bar
3PCS
Metal Cross Bar
Support Bar
2PCS
2PCS
Metal Cross Bar
2PCS
2PCS
NO
1
2
3
4
5
6
7
8
9
10
11

TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
AMachine Screw (6x35mm)
Screw (4x12mm)
Screw (3x12mm)
B
22PCS
Machine Screw (6x30mm)
10PCS
Machine Screw (6x15mm)
4PCS
C
D
6PCS
E
6PCS
F
G
I
J
3PCS
2PCS
2PCS
Coat Hook
Plastic Anchor
Screw (4x55mm)
2PCS Screw (4x60mm)
PARTS LIST
NO PARTS QTY DESCRIPTION
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
STEP 2
F
F
F
F
F
F
7
7
7
3
A
B
B
A
AA
AA
A
A
A
AA
AA
A
3
8
8
4
11
11
5
1. Attach 3 metal cross bars (7) to shelf (3) by inserting 6 machine screws (F) through holes on
metal cross bars (7), then tighten to shelf (3).
1. Attach lower left side frame (4) and support bar (11) to shelf (3) and bottom metal frames (8)
by inserting 7 machine screws (A) and screw (B) through holes on lower left side frame (4)
and support bar (11), then tighten to shelf (3) and bottom metal frame (8).
2. Attach lower right side frame (5) and support bar (11) to shelf (3) and bottom metal frames (8)
by inserting 7 machine screws (A) and screw (B) through holes on lower right side frame (5)
and support bar (11), then tighten to shelf (3) and bottom metal frame (8).

STEP 3
STEP 4
B
B
B
B
2
10
10
F
F
F
F
1
9
9
1. Attach 2 metal cross bars (10) to back panel (2) by inserting 4 screws (B) through holes on
metal cross bars (10), then tighten to back panel (2).
1. Attach 2 metal cross bars (9) to top board (1) by inserting 4
machine screws (F) through holes
on metal cross bars (9), then tighten to top board (1).

STEP 5
STEP 6
A
A
A
A
A
A
A
A
1
2
6
6
1. Attach 2 upper metal side frames (6) to top board (1) and back panel (2) by inserting 8 machine
screws (A) through holes on upper metal side frames (6), then tighten to top board (1) and
back panel (2).
1. Place upper unit onto lower unit. Insert 4
machine screws (E) through holes on metal side
frames (6), then tighten to secure upper unit to lower unit.
2. Attach 3 hooks (D) to back panel (2) by inserting 6 screws (C) through holes on hooks (D),
then tighten to back panel (2).
D
D
DC
C
C
E
E
6
6
2
4
5
3

STEP 7
ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure youritem is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
G
G
I
I
G
I
G
JI
DRYWALL
WALL ANCHOR
WITH SCREW
SCREW
ONLY
DRYWALL
OPTION #2OPTION #1
WOOD
STUD
Option #1: Securing to Drywall
1. Position hall tree against wall in desired location. According to position of holes on metal side
frames (6), using a pencil or part (I) screw, make 2 small marks on wall. Move hall tree away from the
wall and screw 2 plastic anchors (G) into wall on pencil/screw marks.
2. Place hall tree against wall, insert 2 screws (I) through holes on side frames, then tighten to plastic
anchors (G).
Option #2: Securing to Drywall and Wood Stud
1. Position hall tree against wall in desired location. Insert 2 screws (J) through holes on metal side
frames (6), then tighten through drywall and into wood stud.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy Your New RiverRidge®Hall Tree!
To order replacement parts at no cost to you,email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016
Thank you for purchasing this RiverRidge®Home item. We hope you
enjoy it and consider purchasing other RiverRidge®items.