RiverRidge KIDS TABLE W/3 BINS & 2 CHAIRS 01-004 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® KIDS TABLE W/3 BINS & 2 CHAIRS
ITEM # 01-004
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of the small parts. Care should be
taken in unpacking and assembling this item to keep the small parts away from children.
WARNING
Young children can be seriously injured or killed, if furniture tips over.
Don’t use this item for a TV stand.

Send requests for missing or damaged parts replacements by email to :
[email protected] or call toll free 1-(844)-223-5201 or order parts on line at
www.riverridgehome.com
THE CHAIRS HAVE A WEIGHT CAPACITY OF 110 POUNDS AND ARE FOR CHILDREN'S USE ONLY.
DO NOT ALLOW CHILDREN TO STAND ON THE CHAIRS. THE TABLE STORAGE BINS/SHELVES
HAVE A LOAD CAPACITY OF 15 POUNDS EACH. TABLE TOP LOAD CAPACITY IS 50 POUNDS.
FAILURE TO FOLLOW THE LOAD CAPCITIES ABOVE, MAY CAUSE DAMAGE TO TABLE AND
CHAIRS, WHICH MAY CAUSE SERIOUS INJURY OR DEATH.

PARTS LIST

PARTS LIST
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED

STEP 1
STEP 1
1. Attach 6 cross bars (2) to the left side panel (1).
2. Insert 6 long wood screws (A) into the holes on the left side panel (1) then tighten into the holes
on the 6 cross bars (2) by using a Philips screwdriver.
STEP 2
2
3
STEP 2
1. Attach the right side panel (3) to the 6 cross bars (2).
2. Insert 6 long wood screws (A) into the holes on the right side panel (3) then tighten into the holes
on the 6 cross bars (2) by using a Philips screwdriver.

STEP 3
4
5
5
STEP 3
1. Place the top board (4) up-side-down.
2. Attach the 2 support bars (5) to the top board (4).
3. Insert 4 short wood screws (B) into the holes on the 2 support bars (5) then tighten into the holes
on the top board (4) by using a Philips screwdriver.
STEP 4
3
4
STEP 4
1. Screw in 4 cam bolts (C) into the pre-threaded holes on the top board (4).
2. Attach the pre-assembled both side panel (1), (3), and cross bars (2) to the top board (4) by
inserting 4 cam bolts (C) into the holes on the both side panel (1), (3).
3. Insert 4 cam locks (D) into the cam lock holes on the both side panel (1), (3) and rotate clockwise
to lock the 4 cam bolts (C) in place.

STEP 5
5
5
3
STEP 5
1. Insert 4 short wood screws (B) into the holes on the support bars (5) then tighten into the holes
on the both side panel (1), (3) by using a Philips screwdriver.
STEP 6
STEP 6
1. Put the big storage bin (12) into the storage unit.

STEP 7
STEP 7
1. Put the 2 small storage bins (13) into the storage unit.
STEP 8
6
7
STEP 8 - Chairs
1. Insert 2 wood dowels (G) into the holes on the right side leg (6).
2. Attach the 2 chair center cross bars (7) to the right side leg (6) by inserting 2 wood dowels (G)
into the holes on the 2 chair center cross bars (7).
3. Insert 2 barrel nuts (F) into the holes on the 2 chair center cross bars (7), making sure the holes
of the 2 barrel nuts (F) is facing towards the edge of the 2 chair center cross bars (7).
4. Insert 2 long machine screws (E) into the holes on the right side leg (6),and fasten the right side
leg (6) to the 2 chair center cross bars (7) by using a Philips screwdriver to hold the barrel nuts (F)
in place.

STEP 9
6
8
STEP 9
1. Insert 1 wood dowel (G) into the hole on the right side leg (6).
2. Attach the chair back board (8) to the right side leg (6) by inserting 1 wood dowel (G) into the
hole on the chair back board (8).
3. Insert 1 barrel nut (F) into the hole on the chair back board (8), making sure the hole of the 1
barrel nut (F) is facing towards the edge of the chair back board (8).
4. Insert 1 long machine screw (E) into the hole on the right side leg (6), and fasten the right side
leg (6) to the chair back board (8) by using a Flathead screwdriver to hold the barrel nut (F) in
place.
STEP 10
STEP 10
1. Insert 1 wood dowel (G) into the hole on the right side leg (6).
2. Attach the chair lower cross bar (9) to the right side leg (6) by inserting 1 wood dowel (G) into the
hole on the chair lower cross bar (9).
3. Insert the barrel nut (F) into the hole on the chair lower cross bar (9), making sure the hole of the
barrel nut (F) is facing towards the edge of the chair lower cross bar (9).
4. Insert 1 long machine screw (E) into the hole on the right side leg (6), and fasten the right side
leg (6) to the chair lower cross bar (9) by using a Flathead screwdriver to hold the barrel nut (F)
in place.

STEP 11
7
7
STEP 11
1. Insert 4 wood dowels (G) into the holes on the cross bars (7),(9), and chair back board (8).
2. Attach the left side leg (10) to the 2 chair center cross bars (7), chair back board (8) and chair
lower cross bar (9) by inserting 4 wood dowels (G) into the holes on the 2 chair center cross
bars (7), chair back board (8) and chair lower cross bar (9).
3. Insert 4 barrel nuts (F) into the holes on the 2 chair center cross bars (7), chair back board (8)
and chair lower cross bar (9), making sure the holes of the 4 barrel nuts (F) is facing towards the
edge of the 2 chair center cross bars (7), chair back board (8) and chair lower cross bar (9).
4. Insert 4 long machine screws (E) into the holes on the left side leg (10), and fasten the left side
leg (10) to the 2 chair center cross bars (7), chair back board (8) and chair lower cross bar (9) by
using a Philips screwdriver to hold the barrel nuts (F) in place.
STEP 12
STEP 12
1. Attach the seat board (11) to the center cross bars (7), and both side legs (6),(10).
2. Insert 2 Long machine screw (E) and 2 wood dowel (G) into the holes on cross bars (7).and
tighten into the seat board (11) by using a Philips screwdriver.
3. Repeat the above step 8 to step 12 for another chair assembly.

ENJOY YOUR NEW RiverRidge® TABLE / CHAIR NOW !
Attention Adults: The table / chair should be checked periodically for damage or loose screws/parts.
Take appropriate action necessary to correct the hazard such as tightening of screws and taking
any damaged parts away from the children.
Thank you for purchasing this RiverRidge® Kids Products item. We hope you enjoy it, and consider
purchasing other RiverRidge® items.
Send requests for missing or damaged parts replacements by email to :
[email protected] or call toll free 1-(844)-223-5201 or order parts on line at
www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016.