RiverRidge Madison 06-109 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge®Madison Two-Door Wall Cabinet
ITEM #: 06-109 White
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken in
unpacking and assembling this item to keep small parts away from children.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF OR A TOTAL OF 60
POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 20 POUNDS OR 60 POUNDS
TOTAL WEIGHT. IF OVERLOADED WITH. MORE THAN 20 POUNDS PER SHELF OR 60
POUNDS TOTAL WEIGHT, SHELF MAY TIP FROM THE WALL AND CAUSE SERIOUS
INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Bottom Board
3
1PC
Left Side Panel
4
1PC
Right Side Panel
5
1PC
Rear Cross Bar
6
1PC
Shelf
7
1PC
Adjustable Shelf
8
1PC
Left Door
9
1PC
Right Door
10
1PC
Upper Back Panel
11
1PC
Lower Back Panel

TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
TOOL NEEDED FOR SECURING TO WALL: POWER DRILL (NOT INCLUDED)
To order replacement parts at no cost to you, email [e-mail],
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com
PARTS LIST
NO
PARTS
QTY
DESCRIPTION
A
12PCS
Cam Bolt
B
12PCS
Cam Lock
C
6PCS
Wood Dowel (6 x 30mm)
D
4PCS
Metal Shelf Holder
E
4PCS
Hinge
F
2PCS
Handle
G
28PCS
Screw (4 x 12mm)
H
1PC
Plastic Connection Strip
I
14PCS
Screw (2.5 x 10mm)
J
2PCS
Plastic Anchor
K
2PCS
Screw (5 x 45mm)
L
2PCS
Silicon pad

STEP 1
1. Screw 4 cam bolts (A) into pre-threaded holes on top board (1).
2. Screw 4 cam bolts (A) into pre-threaded holes on bottom board (2).
STEP 2
1. Screw 2 cam bolts (A) into pre-threaded holes on left side panel (3).
2. Screw 2 cam bolts (A) into pre-threaded holes on right side panel (4).
STEP 3
1. Insert 2 wood dowels (C) into wood dowel holes on left side panel (3).
2. Attach left side panel (3) to shelf (6) and rear cross bar (5) by inserting cam bolts (A) into cam lock holes
on shelf (6) and wood dowels into wood dowel holes on rear cross bar(5).
3. Insert 2 cam locks (B) into cam lock holes on shelf (6), then rotate clockwise to secure cam bolts in place.
4. Insert 2 wood dowels (C) into wood dowel holes on right side panel (4).
5. Attach right side panel (4) to shelf (6) and rear cross bar (5) by inserting cam bolts into cam lock holes on
shelf (6) and inserting wood dowels into wood dowel holes on rear cross bar (5).
6. Insert 2 cam locks (B) into cam lock holes on shelf (6), then rotate clockwise to secure cam bolts in place.

STEP 4
1. Insert 2 wood dowels (C) into wood dowel holes on top board (1).
2. Attach top board (1) to left side panel (3), right side panel (4) and rear cross bar (5) by inserting wood
dowels into wood dowel holes on rear cross bar (5) and inserting cam bolts into cam lock holes on left
side panel (3) and right side panel (4).
3. Insert 4 cam locks (B) into cam lock holes on left side panel (3) and right side panel (4), then rotate
clockwise to secure cam bolts in place.
4. Attach bottom board (2) to left side panel (3) and right side panel (4) by inserting cam bolts into cam
lock holes on left side panel (3) and right side panel (4).
5. Insert 4 cam locks (B) into cam lock holes on left side panel (3) and right side panel (4), then rotate
clockwise to secure cam bolts in place.
STEP 5
1. Attach upper back board (10) and lower back board (11) together by sliding into plastic connection
strip (H).
2. Attach upper back board (10) and lower back board (11) to cabinet by inserting 14 wood screws (I)
through holes on upper back board (10) and lower back board (11) then tighten into cabinet.

STEP 6
1. Attach 2 hinges (E) to left door (8) by inserting 4 screws (G) through holes on hinges (E), then tighten
to left door (8).
2. Attach 1 handle (F) to left door (8) by inserting 2 screws (G) through holes on handle (F), then tighten
to left door (8).
3. Stick 1 silicon pad (L) on handle (F) to prevent scratches on shelf edge when door is closed.
4. Repeat above steps to assemble hinges (E) and handle (F) and silicon pad (L) to right door(9).
STEP 7
1. Attach left door (8) to cabinet by inserting 8 screws (G) through holes on hinges (E), then
tighten to left side panel (3).
2. Attach right door (9) to cabinet by inserting 8 screws (G) through holes on hinges (E), then
tighten to right side panel (4).
3. Note: Tightening screw in position “a” will adjust doors up or down; tightening screw in position “b” will
adjust doors to or from cabinet and tightening screw in position “c” will adjust doors side to side.
Door Adjustments

STEP 8
1. Place drawing on wall in desired position and drill 2 holes through hole positions on drawing.
2. Insert 2 plastic anchors (J) into the holes.
3. Align holes on cabinet with holes on wall, then insert 2 screws (K) through holes on back of cabinet
and tighten cabinet to wall.
STEP 9
1. Insert 4 metal holders (D) into desired hole positions.
2. Place adjustable shelf (7) onto 4 metal holders (D).
ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose
screws/parts. Take appropriate action necessary to correct hazards such as tightening
of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [e-mail],
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016