RiverRidge Kids Cubby 02-162 User manual

ASSEMBLY INSTRUCTIONS
ITEM #: 02-162 White
RiverRidge®Book Nook
Kids Cubby Storage Cabinet with Bookrack
ADULT ASSEMBLY REQUIRED
WARNING
SEE FULL WARNING ON PAGE 2
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
Young children can be seriously injured or killed if furniture tips over.
Don’t use this item for a TV stand or place heavy objects on top of item.
Always use angle-braces or anchors to secure furniture to the wall.

This product is suitable for children 3 years and older.
THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER CUBBY, 10 POUNDS PER
DRAWER AND 20 POUNDS IN BOOKRACK OR A TOTAL OF 120 POUNDS. DO NOT
LOAD EACH CUBBY WITH MORE THAN 20 POUNDS, EACH DRAWER WITH MORE
THAN 10 POUNDS OR THE BOOKRACK WITH MORE THAN 20 POUNDS.
IF OVERLOADED WITH MORE THAN 20 POUNDS PER CUBBY, 10 POUNDS PER
DRAWER OR 20 POUNDS IN BOOKRACK, THIS MAY CAUSE DAMAGE TO THE
CABINET AND MAY CAUSE SERIOUS INJURY OR DEATH.

1
2
3
4
5
10
12 12
12 12
11
14
15 16
17 17
18 18
19 19
20 20
13
13
6
9
7
8
PARTS LIST

Top Rear Vertical Board1PC
QTYNO DESCRIPTION
1
Top Middle Vertical Board1PC2
Top Front Vertical Board1PC3
Top Board1PC4
Left Side Panel1PC5
Right Side Panel1PC6
Middle Shelf1PC7
Middle Support Panel1PC8
Lower Shelf1PC9
Divider Board1PC10
Bottom Board1PC11
Wood Leg4PCS12
Upper Back Board2PCS13
Lower Back Board1PC14
Left Drawer Front Board1PC15
Right Drawer Front Board1PC16
Drawer Left Side Board2PCS17
Drawer Right Side Board2PCS18
Drawer Back Board2PCS19
Drawer Bottom Board2PCS20
PARTS LIST

Wood Dowel
Cam Bolt
Cam Lock
Screw (4x30mm)
Screw (4x35mm)
Screw (3x12mm)
Screw (4x10mm)
Wood Peg
2PCS
40PCS
26PCS
26PCS
16PCS
2PCS
25PCS
A
B
C
D
E
F
G
Drawer Slides
(attach to left side panel)
2PCS
H
2PCS
J
I
Drawer Slides
(attach to right side panel)
2PCS
KDrawer Slides
(attach to drawer right side board)
2PCS
L
Drawer Slides
(attach to drawer left side board)
2PCS
2PCS
MPlastic Anchor
2PCS
NAdjustable Anchor Bracket
PARTS LIST
NO PARTS QTY DESCRIPTION
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
STEP 2
STEP 3
1. Slide middle shelf (7) onto middle support panel (8).
1. Insert 6 wood dowels (C) into wood dowel holes on top rear vertical board (1), top middle
vertical board (2) and top front vertical board (3).
2. Attach top rear vertical board (1), top middle vertical board (2) and top front vertical board (3)
to top board (4) by inserting wood dowels (C) into wood dowel holes on top board (4).
3. Insert 3 screws (E) through holes on top board (4), then tighten to top rear vertical board (1),
top middle vertical board (2) and top front vertical board (3).
1. Screw 2 cam bolts (A) into cam bolt holes on top board (4).
C
E
E
E
C
C
C
C
C
1
2
3
4
7
8

STEP 5
STEP 4
1. Screw 2 cam bolts (A) into cam bolt holes on lower shelf (9).
1. Insert 4 wood dowels (C) into wood dowel holes on middle support panel (8).
2. Attach lower shelf (9) to middle support panel (8) by inserting wood dowels (C) into wood
dowel holes on lower shelf (9).
3. Insert 2 screws (E) through holes on lower shelf (9), then tighten to middle support panel (8).
4. Attach middle support panel (8) to top board (4) by inserting wood dowels (C) into wood
dowel holes on top board (4) and inserting cam bolts (A) into cam lock holes on middle support
panel (8).
5. Insert 2 cam locks (B) into cam lock holes on middle support panel (8), then rotate clockwise to
secure cam bolts (A) in place.
9
AA

STEP 6
STEP 7
1. Attach drawer slide (H) to left side panel (5) by inserting 2 screws (G) through holes on
drawer slides (H), then tighten to left side panel (5).
2. Attach drawer slide (J) to right side panel (6) by inserting 2 screws (G) through holes on
drawer slides (J), then tighten to right side panel (6).
1. Attach drawer slide (J) to divider board (10) by inserting 2 screws (G) through holes on
drawer slides (J), then tighten to divider board (10).
2. Attach drawer slide (H) to divider board (10) by inserting 2 screws (G) through holes on
drawer slides (H), then tighten to divider board (10).
G
GG
G
GG
G
G
H
H
J
J
5
6
G
G
J
H
H
10
10
STEP 7
G
G
G
G
JJ
H
H
10
10
J
GG

STEP 8
STEP 9
1. Insert 9 wood dowels (C) into wood dowel holes on right side panel (6).
2. Slide upper back board (13) into grooves on top board (4), lower shelf (9) and middle
support panel (8).
3. Attach right side panel (6) to pre-assembled unit by inserting wood dowels (C) into wood
dowel holes and inserting cam bolts (A) into cam lock holes on lower shelf (9), middle shelf (7),
top board (4), top vertical front board (3), top middle vertical board (2) and top rear vertical
board (1).
4. Insert 9 cam locks (B) into cam lock holes on lower shelf (9), middle shelf (7), top board (4),
top vertical front board (3), top middle vertical board (2) and top rear vertical board (1), then
rotate clockwise to secure cam bolts (A) in place.
1. Screw 9 cam bolts (A) into cam bolt holes on right side panel (6).
2. Screw 9 cam bolts (A) into cam bolt holes on left side panel (5).
5
6
A
A
A
A
A
A
A
A
AA
AAA
AAA
A
A
6
4
7
9
13
B
B
B
B
BB
B
C
CC
C
C
C
C

1. Attach 4 wood legs (12) to bottom board (11) by inserting 4 screws (E) through holes on bottom
board (11), then tighten to wood legs (12).
1. Insert 9 wood dowels (C) into wood dowel holes on left side panel (5).
2. Slide upper back board (13) into grooves on top board (4), lower shelf (9) and middle support panel (8).
3. Attach left side panel (5) to pre-assembled unit by inserting wood dowels (C) into wood dowel holes
and inserting cam bolts (A) into cam lock holes on lower shelf (9), middle shelf (7), top board (4), top
vertical front board (3), top middle vertical board (2) and top rear vertical board (1).
4. Insert 9 cam locks (B) into cam lock holes on lower shelf (9), middle shelf (7), top board (4), top vertical
front board (3), top middle vertical board (2) and top rear vertical board (1), then rotate clockwise to
secure cam bolts (A) in place.
STEP 10
STEP 11
E
E
E
11
12
12 12
12

1. Screw 4 cam bolts (A) into cam bolt holes on drawer front boards (15,16).
1. Insert 2 wood dowels (C) into wood dowel holes on lower shelf (9), then attach divider board (10)
to lower shelf (9) by inserting wood dowels (C) into wood dowel holes and inserting cam bolts (A)
into cam lock holes on divider board (10).
2. Insert 2 cam locks (B) into cam lock holes on divider board (10), then rotate clockwise to secure
cam bolts (A) in place.
3. Slide lower back board (14) into grooves on left side panel (5), right side panel (6) and lower shelf (9).
4. Insert 6 wood dowels (C) into wood dowel holes on bottom board (11).
5. Attach bottom board (11) to left side panel (5), right side panel (6), divider board (10) and lower
back board (14), make sure lower back board (14) slides into groove on bottom board (11).
6. Insert 6 screws (E) through holes on bottom board (11), then tighten to left side panel (5), right side
panel (6) and divider board (10).
7. Attach 2 adjustable anchor brackets (N) to top board (4) by inserting 2 screws (L) through holes
on adjustable anchor brackets (N), then tighten to top board (4).
STEP 12
STEP 13
A
A
AA
15 16

1. Slide 1pc drawer bottom board (20) into grooves on drawer left board (17), drawer right board
(18) and drawer back board (19).
2. Insert 2 wood dowels (C) into wood dowel holes on drawer front board (15)
3. Attach drawer front board (15) to drawer left board (17), drawer right board (18) and drawer
bottom board (20) by inserting wood dowels (C) into wood dowel holes and inserting cam
bolts (A) into cam lock holes on drawer left board (17) and drawer right board (18). Make
sure drawer bottom board (20) slides into groove on drawer front board (15).
4. Insert 2 cam locks (B) into cam lock holes on drawer left side panel (17) and drawer right side
panel (18), then rotate clockwise to secure cam bolts (A) in place.
5. Repeat above steps to assemble another drawer front board (16).
1. Attach drawer left board (17) and drawer right board (18) to drawer back board (19) by
inserting 4 screws (E) through holes on drawer left board (17) and drawer right board (18),
then tighten to drawer back board (19).
2. Repeat above step to assemble another drawer left board (17) and drawer right board (18)
to drawer back board (19).
STEP 15
C
CC
C
B
B
B
B
15 16
STEP 14
×2
E
E
E
E17
18
19
20
18
20
17
19 19
18
17
STEP 7
G
G
G
G
JJ
H
H
10
10

1. Slide 2 drawers into cabinet.
STEP 17
1. Attach drawer slides (K) and (I) to drawer by inserting 4 screws (G) through holes on
drawer slides (K, I), then tighten to drawer.
2. Repeat above step to assemble 2 drawer slides (K, I) to other drawer.
STEP 16
15
15 16
GG
GG
K
I
GG
GG
K
I
16

STEP 19
5
1. Attach 2 wood pegs (F) to left side panel (5) by inserting 2 screws (E) through holes on left
side panel (5), then tighten to 2 wood pegs (F).
STEP 18
E
FF
E
M
DD
DRYWALL
WALL ANCHOR
WITH SCREW
SCREW
ONLY
DRYWALL
OPTION #2OPTION #1
WOOD
STUD
M
M
M
N
DDD
Option #1: Securing to Drywall
1. Position cabinet and brackets (N) against wall in desired location. Using a pencil, make 2 small marks on
wall through holes on brackets (N). Move cabinet away from wall and screw 2 plastic anchors (M) into
wall on pencil marks.
2. Place cabinet against wall, insert 2 screws (D) through holes on brackets (N), then tighten to plastic
anchors (M).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet and brackets (N) against wall in desired location. Insert 2 screws (D) through holes on
brackets (N), then tighten through drywall and into wood stud.
*Tip: Anchor brackets (N) can be adjusted to correct distance from wall to cabinet as needed. Once
adjusted, be sure to re-tighten brackets inside cabinet for stability.

ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose
screws/parts. Take appropriate action necessary to correct hazards such as tightening
of screws and taking any damaged parts away from children.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy Your New RiverRidge®Storage Cabinet!
To order replacement parts at no cost to you,email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016
Thank you for purchasing this RiverRidge®Home item. We hope you
enjoy it and consider purchasing other RiverRidge®items.

RiverRidge®Kids Two-Piece Folding Storage Bin
ADULT ASSEMBLY REQUIRED
Thank you for purchasing this RiverRidge®Home item. We hope you
enjoy it and consider purchasing other RiverRidge®items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
For purchases outside of the United States, please contact retailer where purchased.
RiverRidge®is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016
Distributed by:
Sourcing Solutions, Inc.
Hudson, WI 54016
Made in China