RiverRidge 16-029 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge®Woodbury Hall Tree w/ Bench
ITEM #: 16-029
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken in
unpacking and assembling this item to keep small parts away from children.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item.Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF AND CUBBY FOR TOTAL
OF 80 POUNDS. BENCH SEATING WEIGHT CAPACITY IS 200 POUNDS. DO NOT LOAD
SHELVES OR CUBBIES WITH MORE THAN 20 POUNDS OR SEATING WITH MORE
THAN 200 POUNDS. OVERLOADING WITH MORE THAN 20 POUNDS PER SHELF OR
200 POUNDS SEATING MAY CAUSE DAMAGED TOTHE SHELF OR SERIOUS INJURY OR
DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Upper Rear Board
2
1PC
Upper Shelf
3
1PC
Middle Rear Board
4
1PC
Vertical Support Board
5
1PC
Lower Rear Board
6
1PC
Top Board
7
1PC
Cross Bar
8
1PC
Shelf
9
1PC
Divider Board
10
1PC
Bottom Board
11
1PC
Upper Left Side Panel
12
1PC
Upper Right Side Panel
13
1PC
Lower Left Side Panel
14
1PC
Lower Right Side Panel
15
2PCS
Door
16
2PCS
Upper Back Board
17
1PC
Lower Back Board
18
4PCS
Metal Leg

PARTS LIST
NO
PART
QTY
DESCRIPTION
A
14PCS
Cam Bolt
B
14PCS
Cam Lock
C
38PCS
Wood Dowel (8x30mm)
D
8PCS
Screw (4X35mm)
E
8PCS
Machine Screw (6x30mm)
F
8PCS
Shim
G
4PCS
Hinge
H
24PCS
Screw (4x14mm)
I
3PCS
Metal Hook (4x14mm)
J
7PCS
Screw (3x12mm)
K
34PCS
Screw (2.5x10mm)
L
1PC
Plastic Anchor
M
2PCS
Handle
N
4PCS
Machine Screw (4x18mm)
O
2PCS
Bracket
P
1PC
Plastic Lock Strap
Q
1PC
Screw (4x30mm)
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
TOOL NEEDED FOR SECURING TO WALL: POWER DRILL (NOT INCLUDED)
To order replacement parts at no cost to you, email [e-mail],
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com

STEP 1
1. Screw 3 cam bolts (A) into pre-threaded holes on upper left side panel (11).
2. Screw 3 cam bolts (A) into pre-threaded holes on upper right side panel (12).
STEP 2
1. Screw 4 cam bolts (A) into pre-threaded holes on top board (6).
STEP 3
1. Screw 4 cam bolts (A) into pre-threaded holes on lower left side panel (13) and lower right side panel
(14).

STEP 4
1. Insert 4 wood dowels (C) into wood dowel holes on vertical support board (4).
2. Attach middle rear board (3) and lower rear board (5) to vertical support board (4) by inserting wood
dowels (C) into wood dowel holes on middle rear board (3) and lower rear board (5).
STEP 5
1. Insert 8 wood dowels (C) into wood dowel holes on upper right side panel (12).
2. Attach middle rear board (3) and lower rear board (5) to upper right side panel (12) by inserting wood
dowels (C) into wood dowel holes and inserting cam bolts (A) into cam lock holes on middle rear
board (3) and lower rear board (5).
3. Insert 2 cam locks (B) into cam lock holes on middle rear board (3) and lower rear board (5), then
rotate clockwise to secure cam bolts (A) in place.
4. Attach upper shelf (2) to upper right side panel (12) by inserting wood dowels (C) into wood dowel
holes and inserting cam bolt (A) into cam lock hole on upper shelf (2).
5. Insert 1 cam lock (B) into cam lock hole on upper shelf (2), then rotate clockwise to secure cam bolt
(A) in place.
6. Attach upper rear board (1) to upper right side panel (12) by inserting wood dowels (C) into wood
dowel holes on upper rear board (1).

STEP 6
1. Insert 8 wood dowels (C) into wood dowel holes on upper left side panel (11).
2. Attach upper left side panel (11) to upper rear board (1), upper shelf (2), middle rear board (3) and
lower rear board (5) by inserting wood dowels (C) into wood dowel holes and insert cam bolts (A)
into cam lock holes on upper rear board (1), upper shelf (2), middle rear board (3) and lower rear
board (5).
3. Insert 3 cam locks (B) into cam lock holes on upper shelf (2), middle rear board (3) and lower rear
board (5), then rotate clockwise to secure cam bolts (A) in place.
STEP 7
1. Attach 2 upper back boards (16) to pre-assembled unit by inserting 24 screws (K) through holes on 2
upper back boards (16), then tighten to back of unit.

STEP 8
1. Insert 2 wood dowels (C) into wood dowel holes on top board (6).
2. Attach bottom board (6) to upper left side panel (11) and upper right side panel (12) by inserting
wood dowels (C) into wood dowel holes on upper left side panel (11) and upper right side panel (12).
3. Insert 4 screws (D) through holes on top board (6), then tighten to upper left side panel (11) and
upper right side panel (12).
STEP 9
1. Insert 4 wood dowels (C) into wood dowel holes on lower left side panel (13) and lower right side
panel (14).
2. Attach lower left side panel (13) and lower right side panel (14) to shelf (8) by inserting wood dowels
(C) into wood dowel holes and inserting cam bolts (A) into cam lock holes on shelf (8).
3. Insert 4 cam locks (B) into cam lock holes on shelf (8), then rotate clockwise to secure cam bolts (A)
in place.

STEP 10
1. Insert 2 wood dowels (C) into wood dowel holes on divider board (9).
2. Attach divider board (9) to shelf (8) by inserting wood dowels (C) into wood dowel holes on shelf
(8).
3. Insert 6 wood dowels (C) into wood dowel holes on bottom board (10).
4. Attach bottom board (10) to lower left side panel (13), lower right side panel (14) and divider board
(9) by inserting wood dowels (C) into wood dowel holes on lower left side panel (13), lower right
side panel (14) and divider board (9).
5. Insert 4 screws (D) through the holes on bottom board (10), then tighten to lower left side panel (13)
and lower right side panel (14).
STEP 11
1. Attach 4 metal legs (18) to bottom board (10) by inserting 8 machine screws (E) through holes on
shims (F) and holes on metal legs (18), then tighten to bottom board (10).

STEP 12
1. Insert 4 wood dowels (C) into wood dowel holes on top board (6).
2. Place cross bar (7) onto grooves on lower left side panel (13) and lower right side panel (14).
3. Attach pre-assembled upper section to pre-assembled lower section by inserting wood dowels (C)
into wood dowel holes and inserting cam bolts (A) into cam lock holes on lower left side panel (13)
and lower right side panel (14).
4. Insert 4 cam locks (B) into cam lock holes on lower left side panel (13) and lower right side panel (14),
then rotate clockwise to secure cam bolts (A) in place.

STEP 13
1. Attach lower back board (17) to back of cabinet by inserting 10 screws (K) through holes on lower
back board (17), then tighten to back of cabinet.
STEP 14
1. Attach 2 hinges (G) to door (15) by inserting 4 screws (H) through holes on hinges (G), then tighten
to door (15).
2. Attach handle (M) to door (15) by inserting 2 screws (N) through holes on door (15), then tighten to
handle (M).
3. Repeat above steps for another door (15).
STEP 15

1. Attach 1 door (15) to cabinet by inserting 8 screws (H) through holes on hinges (G), then tighten to
lower left side panel (13).
2. Attach 1 door (15) to cabinet by inserting 8 screws (H) through holes on hinges (G), then tighten to
lower right side panel (14).
3. Attach 3 metal hooks (I) to middle rear board (3) by inserting 6 screws (J) through holes on metal
hooks (I), then tighten to middle rear board (3).
4. Note:Tightening screw in position “a” will adjust door up or down; tightening screw in position “b”
will adjust door to or from cabinet and tightening screw in position “c” will adjust door side to side.
Door Adjustments

STEP 16
1. Place drawing with hole position in desired location and drill holes on wall.
2. Insert 1 plastic anchor (L) into hole on wall.
3. Attach bracket (O) to plastic anchor (L) by inserting 1 screw (Q) through hole on bracket (O), then
tighten to plastic anchor (L) in wall.
4. Attach another bracket (O) to back of middle rear board (3) by inserting 1 screw (J) through hole on
bracket (O), then tighten to back of middle rear board (3).
STEP 17
1. Place cabinet against the wall and close to the bracket (O).
2. Insert plastic lock strap (P) through hole on bracket (O) on cabinet, then through hole on bracket (O)
on wall and fasten plastic lock strap (P) to fix 2 brackets (O) firmly together.

ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose
screws/parts.Take appropriate action necessary to correct hazards such as tightening
of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item.We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [e-mail],
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson,WI 54016