RiverRidge 06-001 User manual

- 1 -
ASSEMBLY INSTRUCTIONS
RiverRidge® X-FRAME BATH 4 SHELF TOWER-WHITE ITEM# 06-001
RiverRidge® X-FRAME BATH 4 SHELF TOWER-ESPRESSO ITEM# 06-002
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of the small parts. Care should be
taken in unpacking and assembling this item to keep the small parts away from children.
WARNING
Young children can be seriously injured or killed, if furniture tips over.
Don’t use this item for a TV stand.
Use angle-braces or anchors to secure furniture to the wall.

- 2 -
Send requests for missing or damaged parts replacements by email to :
[email protected] or call toll free 1-(844)-223-5201 or order parts on line at
www.riverridgehome.com
THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 100 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED WITH MORE THAN 25
POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS
INJURY OR DEATH.

- 3 -
PARTS LIST
NO PARTS QTY DESCRIPTION
1 1PC TOP BOARD
2 2PCS SIDEFRAME
3 3PCS SHELF
4 1PC BACK CROSS BAR
5 1PC FRONT CROSS BAR
A 16PCS LONG WOOD SCREW 5x45mm
B 4PCS WOOD SCREW 4x35mm
C 16PCS PLASTIC CAP
D 2PCS WOOD SCREW 4x40mm
E 2PCS PLASTIC ANCHOR
F 1PC ALLEN WRENCH
TOOLS NEEDED FOR ASSEMBLY: PHILIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED

- 4 -
STEP 1
STEP 1
1. Put the top board (1) upside down on a soft padded surface.
2. Attach the back cross bar (4) to the top board (1) by inserting 2 wood screws (B) through the
holes on the back cross bar (4). Then tighten to the top board (1) by using a Philips screwdriver.
3. Repeat the above step to assemble the front cross bar (5).
STEP 2
STEP 2
1. Attach the top board (1) to 1 side frame (2) by inserting 2 long wood screws (A) through the
holes on the side frame (2) then tighten to the back cross bar (4) and the front cross bar (5) by
using the Allen wrench (F).
2. Attach 1 shelf (3) to the side frame (2) by inserting 2 long wood screws (A) through the holes on
the side frame (2). Then tighten to the shelf (3) by using the Allen wrench (F).
3. Repeat the above step to assemble the other 2 shelves (3).

- 5 -
STEP 3
STEP 3
1. Attach the other side frame (2) to the top board (1) and 3 shelves (3).
2. Insert 2 long wood screws (A) through the holes on the side frame (2) and tighten to the front and
back cross bars (4 & 5).
3. Inserting 6 long wood screws (A) through the holes on the side frame (2) and tighten 2 long wood
screws (A) into each shelf (3) separately.
STEP 4
STEP 4
1. Press 8 plastic caps (C) into the wood screw holes on 1 side frame (2). If added pressure is
needed to keep the plastic cap in place – cover the cap with a piece of paper and tap lightly with
a hammer to secure the cap.
2. Press another 8 plastic caps (C) into the wood screw holes on the other side frame (2).

- 6 -
STEP 5
STEP 5
1. Drill 2 holes on the wall by using the template drawing(included) w/hole positions as a guideline.
2. Insert 2 plastic anchors (E) into the 2 holes on the wall.
3. Insert 2 wood screws (D) through the holes on the back cross bar (4) and tighten to the 2 plastic
anchors (E) with a Philips screwdriver.

- 7 -
ENJOY YOUR NEW RiverRidge® 4 SHELF TOWER NOW !
Attention Adults: The cabinet should be checked periodically for damage or loose screws/parts.
Take appropriate action necessary to correct the hazard such as tightening of screws and taking
any damaged parts away from the children.
Thank you for purchasing this RiverRidge® Home Products item. We hope you enjoy it, and
consider purchasing other RiverRidge® items.
Send requests for missing or damaged parts replacements by email to :
[email protected] or call toll free 1-(844)-223-5201 or order parts on line at
www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016.