Vivo DESK-EP40TB User manual

Black 40" x 24" Electric Desk
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-ep40tb
SKU: DESK-EP40TB
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING!
PACKAGE CONTENTS
A (x2)
Desktop
B x1)
Crossbar
C(x2)
Side Bracket
D(x1)
Sync Rod
E(x1)
Leg
F (x1)
Motorized Leg
G x2)
Foot
I (x1)
AC Adapter
S-A (x4)
M8x47
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S-B (x6)
M6x10
S-C x8)
M6x35
S-D (x26)
M5x16
S-E (x2)
Cable Clip
T-A (x1)
2mm Allen
Wrench
T-B (x1)
4mm Allen
Wrench
T-C x1)
5mm Allen
Wrench
H x3)
Connecting Plate
J (x4)
Foot Pad
S-F (x12)
Rubber Pad
NOTE SOME EXTRA HARDWARE INCLUDED MAY NOT BE USED.

3
176lbs
(80kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
Phillips
Screwdriver
Drill
Level
B
A
C
D
C
E
F
G
G
H
I

4
Place Feet (G) on top of Legs (E, F) and attach using M6x35 Screws (S-C) and 5mm Allen Wrench (T-C).
Screw Foot Pads (J) into Feet (G).
S-C
T-C
J
G
G
E
F
S=5mm
Foot (x4)
S=5mm
M6×35mm (x8)
STEP 1
ASSEMBLY STEPS
Attach Crossbar (B) to Leg (E) and Motorized Leg (F) using M8x47 Screws (S-A) and 5mm Allen Wrench
(T-C).
S=5mm
S=5mm
M8×47mm(x4)
B
F
E
T-C
S-A
S-A
T-C
T-C
J

5
STEP 2
Mount Side Brackets (C) to Legs (E, F) using M6x10 Screws (S-B) and 4mm Allen Wrench (T-B). Loosen
the nut on Sync Rod (D), then insert the rod into Leg (E) and extend to Motorized Leg (F) and retighten
the nut. Tighten the preinstalled set screw in Sync Rod (D) using 2mm Allen Wrench (T-A). Insert
Rubber Pads (S-F) into the desktop mounting holes in the desk frame assembly.
Rubber Pad(x10)
S=4mm
M6×10mm(x4)
S=2mm
S=4mm
C
C
S-B
D
E
F
S-F
T-A
S-B
T-B
F
E
T-B
T-A
S-F
Loosen the nut on
the Sync Rod (D).
Insert the Sync Rod
(D) into the hex hole
in Leg (E) and turn
it counter clockwise
until the it reaches
its lowest postion.
Insert the other end
of Sync Rod (D) into
the slot on Motorized
Leg (F). Secure the
Sync Rod (D) to the
slot by tightening the
pre-installed set screw using 2mm Allen
Wrench (T-A).
Tighten the nut

6
STEP 3
Assemble both halves of Desktop (A) using Connecting Plates (H) and M5x16 Screws (S-D). Tighten
using Phillips screwdriver. Place desk frame assembly upside down on top of Desktop (A) and secure
using M5x16 Screws (S-D).
M5×16mm(x12)
M5×16mm(x10)
A
S-D
H
S-D
S-D
S-D

7
STEP 4
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.
Mount the control panel on Motorized Leg (F) to Desktop (A) using M5x16 Screws (S-D). Connect the
AC Adapter (I) to the cable from the Motorized Leg (F), then plug the AC Adapter (I) into a wall outlet to
power on the desk for operation. Organize cables using the Cable Clips (S-E).
Cable Clip (x2)
M5×16mm(x2)
I
S-D
S-D
S-E
S-E
F
A

LAST UPDATED: 04/15/2021
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303