Robe Anolis Calumma S MC User manual

Version 1.
6
QR code for user manual

Calumma S
2
Table of contents
1. Safety instructions ...................................................................................................................................................... 3
2. Fixture exterior view ................................................................................................................................................... 5
3. Installation .................................................................................................................................................................. 5
3.1 Mounting the fixture ............................................................................................................................................ 5
3.2 Connection to mains ............................................................................................................................................. 8
4. Control and connection options ............................................................................................................................... 10
4.1 DMX or DALI........................................................................................................................................................ 10
4.2 Power On/Off ...................................................................................................................................................... 10
4.3 DMX or Ethernet via E-box ................................................................................................................................. 11
5. Software update ....................................................................................................................................................... 13
6. Technical specifications ............................................................................................................................................ 15
7. Cleaning and maintenance ....................................................................................................................................... 20
7.1 Disposing of the product .................................................................................................................................... 20
8. ChangeLog ................................................................................................................................................................ 20

Calumma S
3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR Calumma !
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure
safe operation, it is absolutely necessary for the user to follow the safety instructions and warnings written in this
manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual
or any unauthorized modification to the device.
Unauthorized modification will void warranty.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!
This fixture should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized distributor or local power company.
Always disconnect the fixture from AC power before servicing or cleaning.
Make sure the power/data cable is not damaged by sharp edges.
Do not install the unit near an open flame.
Refer servicing to qualified service personnel.
This fixture falls under protection class I. Therefore this fixture has to be connected to a mains socket outlet with
a protective earthing connection.
Do not connect this fixture to a dimmer pack.
LED light emission. Risk of eye injury. Do not look into the beam from a short distance without suitable protective
eyewear. Do not look at LEDs with magnifiers or similar optical instruments that may concentrate the light
output.
The fixture was designed for outdoor use. This fixture must not be used for underwater installation.
When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat or dust.
Avoid using the unit in locations subject to possible impacts.
The fixture body never must be covered with cloth or other materials when the fixture is under operation.
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
The fixture becomes hot during operation. Allow the fixture to cool approximately 30 minutes prior to servicing or
maintenance.
Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons!

Calumma S
4
Please use the original packaging if the fixture is to be transported.
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the warranty becomes void. Furthermore, any other operation may lead to dangers like short-circuit,
burns, electric shock etc.
The product (covers and cables) must not be exposed to a high frequency electromagnetic field higher than 3V/m.
Immunity of the equipment is designed according to the standard EN 55035 Electromagnetic compatibility of
multimedia equipment - Immunity requirements
Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility of multimedia
equipment – Emission Requirements according to class B.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
The [Device] wireless operation is safe and complies to RF Exposure requirements.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning for fixtures with Harsh Environment Finish (HEF):
Handle with care!
Avoid any damage to the painted surface.
Damaging the paint may result in corrosion and loss of warranty.

Calumma S
5
2. Fixture exterior view
3. Installation
3.1 Mounting the fixture
The Calumma S can be fastened in any orientation on a flat, non-flammable surface by means of mounting yoke
(2).
The LED module (4) can be tilted +180°/-180°. Use an Allen key 2.5 for adjusting a LED module position.
Ensure that the structure to which you are attaching the fixture is secure.
1. Transparent glass cover
2. Mounting yoke
3. Tilt adjusting lock
4. LED module with heat sink

Calumma S
6
Mounting the fixture via the pole clamp adaptor
The pole clamp adaptor serves as a fastening element for Calumma S on a pole of diameter of 76-116mm or on the
flat pole. The Calumma S has to be equipped with a modified mounting yoke (P/N 11418772 ) intended for this way
of installation.
The pole clamp adaptor set includes: 1x pole clamp adaptor, 1x rubber cable gland, 3x Allen screw M8x20, 3x flat
washer, 3x spring washer, 2x tube spacer.
1. The pole clamp adaptor can be screwed on the pole by means of two screws or fixed by means of
a steel clamping tape (max. width of tape=20mm).
If you use two screws for fastening the pole clamp adaptor on the pole, drill two holes (1) for fastening the
pole clamp adaptor on the pole. Diameter of holes depends on material of pole and used screws. Be sure
that fastening of the pole clamp adaptor is secure to keep weight of Calumma.
2. Drill the hole (2) for rubber cable gland (diameter of hole=20mm, max. thickness of pole wall= 3.2mm),
make drilled hole edges clean (without burrs) and insert the rubber gland into the hole.

Calumma S
7
3. Screw the pole clamp adaptor (4) on the pole by means of two screws (5) with spring washers or use a
steel clamping tape for fastening the pole clamp adaptor on the pole.
In case of screwing the pole clamp adaptor (7) on a flat surface (pole), two pole spacers have to be inserted
under two mounting holes of the pole clamp adaptor (on fastening screws (5)) to fill up space between
the pole and the pole clamp adaptor
4. Pass the Calumma cable (6) through mounting yoke (7), pole clamp adaptor (4) and through cable gland (2)
into the pole.
5. Screw the Calumma mounting yoke (7) on the pole clamp adaptor (4) by means of three Allen screws
M8x20 (3) with washers (Allen screw + spring washer+ flat washer). Keep correct orientation of the
fastening screws (3) as drawn on the picture – two screws (B) have to aim upwards, one screw has to be
orientated towards ground.
NOTE. Three mounting openings in the mounting yoke allow positioning of the mounting yoke in range of
0°- 360°.

Calumma S
8
3.2 Connection to mains
The unit must be installed by a qualified electrician in accordance with all national
and local electrical and construction codes and regulations.
This device falls under class one and must be grounded!
The Calumma is equipped with auto-switching power supply that automatically adjusts to any 50/60Hz AC power
source from 120-277 Volts.
3.2.1 Junction box installation
The junction box box falls under protection class I . Therefore, every junction box
has to be connected to a mains socket outlet with a protective earthing connection.
1.Unscrew the four screws (1) from the cover (2) on the junction box to get access to the terminal block (3) and
two mounting holes of diameter of 4.6 mm (4).
2. Screw the junction box on a non-flammable flat surface.
3. Connect cables.
The cable gland M20 x 1.5 with a standard seal serves for a cable of diameter of 7-13mm, for smaller diameter of
cable (4-8mm) you have to remove the original seal from the cable gland M20x1.5 and use the enclosed reducing
seal instead of it. The reducing seal for diameter of cable 4-8mm (P/N 13051388) is enclosed in the Junction box.
Remove the end cap from the cable gland before passing the cable.
We recommend to apply an adequate layer of the paste LOCTITE 5331 on the plastic holder of the cable gland
before inserting it into the body of the gland.

Calumma S
9
Cable gland M20x1.5:
4. Screw the cover (2) back on the junction box.

Calumma S
10
4. Control and connection options
4.1 DMX or DALI
Example
DMX connection (CE)
IF the 5-cored cable Flamar 3x AWG 16 + 1x (2x AWG 24), (P/N 1305 1508) is used for Calumma connection and
connection among junction boxes:
Core
Connection
Core
Connection
Black
Live
(L)
Red
Data + (+)
Blue
Neutral
(N)
White
Data
–
(
-
)
Yellow/Green
GND
Shielding
Data ground (0V)
Up to 32 Calummas can be connected in DMX chain.
DALI connection
IF the 5-cored cable SJTW 5x 14AWG (P/N 1305 3336) is used for Calumma connection and connection among
junction boxes:
Core
Connection
Core
Connection
Black
Live
(L)
Red
Data
White
Neutral
(N)
Orange
Data
Yellow/Green
GND
Up to 64 Calummas can be connected in DALI network.
4.2 Power On/Off
Note: This type of connection is available for SC (single chip) version only. Non dimmable.

Calumma S
11
4.3 DMX or Ethernet via E-box
Example with junction boxes
Pass Through mode is intended for this connection. Max. 32 fixtures can be connected to one LED output of the E-
Box (Star, Daisy, Lite) in this mode.
CE version
IF the 5-cored cable Flamar 3x AWG 16 + 1x (2x AWG 24), (P/N 1305 1508) is used for Calumma connection and
connection among junction boxes:
Core
Connection
Core
Connection
Black
Live
(L)
Red
Data + (+)
Blue
Neutral
(N)
White
Data
–
(
-
)
Yellow/Green
GND
Shielding
Data
ground (0V)

Calumma S
12
US version
IF the 6-cored cable SJTW 6x 14AWG, (P/N 1305 3480) is used for Calumma connection and connection among
junction boxes:
Core
Connection
Core
Connection
Black
Live (L)
Red
Data + (+)
White
Neutral (N)
Orange
Data
–
(
-
)
Yellow/Green
GND
Blue
Data ground (0V)
Number of connected Calummas to one E-box output depends on a cable length, power voltage, type of Calumma
and E-box operation mode.
The tables below state max. theoretical number of Calummas connected to the one LED output of the E-box.
Table for Pass-Through mode of E-boxes.
Calumma S
MC
Voltage
Cable length *
120V
190V
230V
277V
10 m
32
32 32 32
20 m
32 32 32 32
30 m
32
32
32 32
50 m
26
32 32 32
70 m
18
32 32 32
100 m
13
32 32 32
Calumma S
SC
Voltage
Cable length *
120V
190V
230V
277V
10 m
32 32 32 32
20 m
32 32 32 32
30 m
32 32 32 32
50 m
26 32 32 32
70 m
18 32 32 32
100 m
13 32 32 32
* Cable length is a total cable length between power supply (e.g. E-box) and last connected Calumma.
Example: Total cable length=L1+L2+L3+L4+L5+L6

Calumma S
13
5. Software update
Software update of Calumma S modules has to be done by means of the software ROBE Uploader running on PC.
The ROBE Uploader is a software for automatized software update of ROBE fixtures. The ROBE Uploader switches
Calummas S to the update mode automatically.
Please see https://www.robe.cz/robe-uploader/ for more information.
The Calummas S have to be operated in the Pass-Through mode.
To update Calummas S including the E-box.
1. Update connected LED modules by means of the file Calumma.lib in the ROBE Uploader.
2. Set the E-box to the Standard mode and switch it off/on. Use the file EminereEbox.lib in
the ROBE Uploader for software update of the E-box.
3. After updating the E-box, set the E-box to the Pass-Through mode and switch it off/on.
For more information about updating please see the E-box Lite/Daisy/Star user manual.
Note: Calummas S in DALI connection and ON/OFF connection cannot be updated.
Examples of connection:
1. By means of DMX connection and RUNIT. Connection via junction boxes.

Calumma S
14
2. By means of the Ethernet connection. Connection via junction boxes.
DMX connection
For updating of Calumma modules, use the file Calumma.lib.

Calumma S
15
6. Technical specifications
Power supply
• Electronic auto-ranging
• Input voltage: 120 - 277V AC, 50/60 Hz
• Power consumption:
Calumma S MC: 30 W
Calumma S SC: 30 W
• Inrush current:
Calumma S MC: 60A/230VAC, 30A/115VAC
Calumma S SC: 60A/230VAC, 30A/115VAC
Optic
• Light source:
Calumma S MC: 3 x high power multichip LEDs
Calumma S SC: 19 x high power single chip LEDs
• Colour variants: RGBW (W - 6500 K), RGBA, PW (W - 3000 K)
• Beam Angle Calumma S MC:
Symetrical: 9°, 15°, 25°, 30°, 45°, 65°, 100°
Bi-symetrical: 10° x 30°, 30° x 10°, 10° x 60°, 60° x 10°, 15° x 45°, 45° x 15°,
15°x90°, 90°x15°, 30°x60°, 60°x30°, 30°x90°, 90°x30°
• Beam Angle Calumma S SC:
Symetrical: 10°, 15°, 25°, 30°, 45°, 65°, 100°
Bi-symetrical: 10° x 30°, 30° x 10°, 10° x 60°, 60° x 10°, 15° x 45°, 45° x 15°,
15°x90°, 90°x15°, 30°x60°, 60°x30°, 30°x90°, 90°x30°
Asymmetrical side, Asymmetrical forward
• Projected Lumen Maintenance: L90B10 >90.000 hrs, Ta = 25°C / 77°F
Compatible drivers
• E-box Daisy
1 Output
1 Main power Input
Control: DMX, Art-Net, sACN , W-DMX control, RDM
Pixel control
120-277V Input
Connection via terminal blocks, inlets via grommet
IP67
• E-box Star
6 outputs
1 Main power Input
Control: DMX, Art-Net, sACN , W-DMX control, RDM
Pixel control
120-277V Input
Connection via terminal blocks, inlets via grommet
IP67
• E-box Lite
1 output
1 Main power Input
Control: DMX, W-DMX control, RDM
Pixel control
120-277V Input
Connection via screw terminal blocks, inlets via grommet
IP67

Calumma S
16
Mounting method
• Via yoke
• Adjustability: -180°/+180°
Housing
• High pressure die-cast aluminium body
• Tempered glass
Cooling system
• Convection
Total heat dissipation
• Calumma S MC: 77 BTU/h (calculated)
• Calumma S SC: 77 BTU/h (calculated)
Protection factor
• CE: IP 67 (IP 66 junction box)
• US: Suitable for wet location
Impact rating
• IK10
Operating ambient temperature range
• -20°C /+40°C (-4°F /+104°F)
Connection - CE
• DMX connection
Calumma IN: Flamar 3x AWG 16 + 1 x (2x AWG 24), Standard 1m with bare-end (P/N 1305 1508)
Interconnecting cables: Flamar 3x AWG 16 + 1 x (2x AWG 24) (P/N 1305 1508)
Junction box (P/N 1098 0714)
• DALI connection
Calumma IN: SJTW 5x 14AWG, standard 1m with bare-end (P/N 1305 3336)
Interconnecting cables: SJTW 5x 14AWG (P/N 1305 3336)
Junction box (P/N 1098 0714)
• DMX or Ethernet via E-box and Junction box
Calumma IN: Flamar 3x AWG 16 + 1x (2x AWG 24), standard 1m with bare-end (P/N 1305 1508)
Interconnecting cables: Flamar 3x AWG 16 + 1 x (2x AWG 24), (P/N 1305 1508)
Junction box (P/N 1098 0714)
Connection - US
• DALI connection
Calumma IN: SJTW 5x 14AWG, standard 1m with bare-end (P/N 1305 3336)
Interconnecting cables: SJTW 5x 14AWG (P/N 1305 3336)
Junction box (P/N 1098 0714)
• DMX or Ethernet via E-box and Junction box
Calumma IN: SJTW 6x 14AWG ,standard 1m with bare-end (P/N 1305 3480)

Calumma S
17
Interconnecting cables: SJTW 6x 14AWG ,(P/N 1305 3480)
Junction box (P/N 1098 0714)
Weight
• Calumma S SC: 3.44 kg (7.6 lbs)
• Calumma S MC: 3.68 kg (8.11 lbs)
Dimensions (All dimensions in mm [inch])

Calumma S
18
Calumma S with Pole clamp adaptor
Pole clamp adaptor for Calumma

Calumma S
19
Junction box
Included items
• 1 x Calumma S MC / Calumma S SC
• 1 x User manual
Optional accessories
Junction Box for Calumma, 1x Output, Ral 9006 (P/N 10980757)
Junction Box for Calumma, 1x Output, Ral 9011 (P/N 10980714)
Top Hat Calumma S RAL9011 (P/N 10980733)
Half Top Hat Calumma S RAL9011 (P/N 10980737)

Calumma S
20
Pole clamp adaptor for Calumma RAL 9011 (P/N 10980783)
Tenon Adaptor for Calumma S
Pole Mount Bracket for Calumma S
E-box Daisy (P/N 10063655)
E-box Daisy/W (P/N 10063638)
E-box Lite (P/N 10063657)
E-box Lite/W (P/N 10063653)
E-box Star (P/N 10063656)
E-box Star/W (P/N 10063644)
7. Cleaning and maintenance
DANGER !
Disconnect from the mains before starting any maintenance or cleaning work
Rinse off loose dirt with low pressure water spray. Wash the housing with a soft brush or sponge and a mild, non-
abrasive washing detergent. Rinse it.
Maintenance and service operations are only to be carried out by a qualified person.
Should you need any spare parts, please use ROBE OEM parts.
7.1 Disposing of the product
To preserve the environment please dispose or recycle this product at the end of its life according to the local
regulations and codes.
8. ChangeLog
This section summarizes changes in the user manual.
Version of manual
Date of issue
Description of changes
1.1
12/10/2022
DMX chart ver.1.1 added
1.2
05/01/2023
Software update description changed
1.3
10/02/2023
DMX chart ver. 1.2 added
1.4
17/02/2023
Pole adaptor for Calumma added
1.5
22/02/2023
Power ON/Off connection description changed
1.
6
17/03/2023
EMC notes added
Specifications are subject to change without notice.
March 16, 2023
Copyright © 2022-2023 Robe Lighting - All rights reserved
Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o. Palackeho 416/20 CZ 75701 Valasske Mezirici