Robot Coupe Blixer 5 G User manual

04/09/2020
Blixer®5 g• Blixer®5 V.V. g• Blixer®7 • Blixer®7 V.V.
New
Register
your product
on line

www.robot-coupe.com
Register your product on line

2
04/09/2020
EU Declaration of Conformity
• the provisions of the following harmonized European standards and the
standards specifying the safety and hygiene requirements:
- EN ISO 12100:2010 Safety of machinery – General principles for
design,
- EN 60204-1:2006 Safety of machinery – Electrical equipment of
machines,
- EN 60529 Degrees of protection provided by enclosures (IP Code):
- IP 55 for the electric controls,
- IP 34 for the other parts of the machine,
• and according to the category of the apparatus, with the provisions of
the following harmonized European standards specifying the safety and
hygiene requirements:
- EN 454 ........................... Planetary Mixers,
- EN 1678........................ Vegetable Cutting Machines (and Juice Extractors),
- EN 12852.................... Food Processors and Blenders,
- EN 12853.................... Hand-Held Blenders and Whisks (Power Mixers),
- EN 13208.................... Vegetable Peelers,
- EN 13621.................... Salad Dryers,
- EN 14655.................... Baguette Slicers.
"R019"
Robot-Coupe®SNC declares that all the machines subject of these original
instructions, as well as their accessories and their packaging, comply with:
• the essential requirements of the following European directives and with
the corresponding national regulations :
- Directive "Machinery" 2006/42/EC,
- Directive "Low Voltage" 2014/35/EU,
- Directive "Electromagnetic Compatibility" 2014/30/EU,
- Directive "Reduction of Hazardous Substances in Electrical Equipment"
(RoHS) 2011/65/EU,
- Directive "Waste Electrical and Electronic Equipment"(WEEE)
2012/19/EU,
• Regulation (EC) No 1907/2006 (latest consolidated version)
«concerning the Registration, Evaluation, Authorisation and Restriction
of Chemicals (REACH)»and as such, no product, accessory and their
packaging sold by Robot-Coupe®SNC, contains any substance on the
European Chemical Agency (ECHA) candidate list and considered of
very high concern.
• Regulation (EC) No 1935/2004 «Materials and articles intended
to come into contact with food» modified by regulation (EC) No
596/2009.
• Regulation (EC) No 2023/2006 «Good manufacturing practice for
materials and articles intended to come into contact with food».
• Regulation (EU) No 10/2011 «Plastic materials and articles intended
to come into contact with food», as well as all relevant (EU) regulations
which modify, correct and/or rectify it, as at the date of this declaration,
the regulations (EU) No 1282/2011, 1183/2012, 202/2014,
865/2014, 2015/174, 2016/1416, 2017/752, 2018/79,
2018/213, 2018/831 and 2019/37.
Montceau-en-Bourgogne, on March 1st, 2019
Jean-Marie LOZANO
Director of Industrial Operations
Robot-Coupe®SNC - 12 avenue du Maréchal Leclerc – BP 134 – 71305 Montceau-en-Bourgogne Cedex - France

3
04/09/2020
SUMMARY
WARRANTY
IMPORTANT WARNING
INTRODUCTION TO YOUR NEW
EMULSIFIER-MIXER Blixer®5 g•
Blixer®5 V.V. g• Blixer®7 • Blixer®7 V.V.
SWITCHING ON THE MACHINE
•Advices on electrical connections
•Control panel
•Timer
ASSEMBLY
USES & EXAMPLES
HYGIENE
CLEANING
•Motor Base
•Bowl
•Blade
•Blixer®arm
MAINTENANCE
•Blade
•Blixer®arm
•Motor seal
TECHNICAL SPECIFICATIONS
•Weight
•Dimensions
•Working height
•Noise level
•Electrical data
SAFETY
STANDARDS
TECHNICAL DATA
•Electrical and wiring diagram

4
04/09/2020
ROBOT-COUPE s.n.c., LIMITED WARRANTY
Your new ROBOT-COUPE appliance is
warranted to the original buyer for a
period of one year from the date of sale
if you bought it from ROBOT-COUPE
s.n.c.
If you bought your ROBOT-COUPE
product from a distributor your product
is covered by your distributor’s warranty
(Please check with your distributor terms
and conditions of the warranty).
The ROBOT-COUPE s.n.c.limited
warranty is against defects in material
and/or workmanship.
The ROBOT-COUPE s.n.c.warranty is
given expressly and in lieu of all other
warranties, expressed or implied, for
merchantability and for fitness toward
a particular purpose and constitutes the
only warranty made by ROBOT-COUPE
s.n.c.France.
THE FOLLOWING ARE NOT COVERED
BY THE ROBOT-COUPE s.n.c.
WARRANTY:
1 - Damage caused by abuse, misuse,
dropping, or other similar damage caused by
or resulting from failure to follow assembly,
operating, cleaning, user maintenance or
storage instructions.
2 - Labour to sharpen and/ or replacements
for blades which have become blunt, chipped or
worn after a normal or excessive period of use.
3 - Materials or labour to replace or repair
scratched, stained, chipped, pitted, dented or
discoloured surfaces, blades, knives, attachments
or accessories.
4 - Any alteration, addition or repair that
has not been carried out by the company or an
approved service agency.
5 - Transportation of the appliance to or from
an approved service agency.
6 - Labour charges to install or test new
attachments or accessories (i.e., bowls, discs,
blades, attachments) which have been arbitrarily
replaced.
7 - The cost of changing direction-of-rotation
of electric motors (Installer is responsible).
8 - SHIPPING DAMAGES. Visible and latent
defects are the responsibility of the freight
carrier. The consignee must inform the carrier
and consignor immediately, or upon discovery in
the case of latent defects.
KEEP ALL ORIGINAL CONTAINERS AND
PACKING MATERIALS FOR CARRIER
INSPECTION.
Neither ROBOT-COUPE s.n.c. nor its affiliated
companies or any of its distributors, directors,
agents, employees, or insurers will be liable for
indirect damage, losses, or expenses linked to
the appliance or the inability to use it.

5
26/10/2020
RECOMMENDATIONS CONCERNING THE INSTALLATION OF VARIABLE-SPEED
APPLIANCES AND PERSONAL SAFETY
These recommendations apply to machines
equipped with an induction motor and a single-
phase wobbulator.
NB :
- The electrical circuit and the protective devices
must comply with national regulations.
- The machine must be wired in by a qualified
electrician
Protecting your appliance
• Like all electronic devices, wobbulators include
components that are sensitive to electrostatic
discharges (ESDs). Before conducting any work
on these wobbulators, technicians must therefore
rid themselves of electrostatic charges.
• The machine must be disconnected from the
mains supply before any internal connection
operations are carried out.
• Repeatedly switching on the appliance will cause
the wobbulator to overload and may result in its
destruction. After the machine has been switched
off, you must wait for 3 minutes before switching
it back on again.
Wiring
• The appliance requires single-phase current as
far as the wobbulator, which turns the latter into
variable-speed three-phase current to supply the
motor.
• You must connect the machine to a 220 - 240 V
/ 50 or 60 Hz single-phase alternating current
supply with an earthed socket. A higher voltage
will destroy the wobbulator.
• The earthed socket ensures operator safety.
Circuit interrupters ensuring user safety
Ground fault circuit interrupters (GFCIs) intended
for variable-speed appliances need to be selected
with great care in order to ensure operator
safety. GFCIs may be sensitive to alternating
current (type AC), impulse current (type A) or all
currents (type B).
Danger ! Wobbulators feature a bridge-
connected rectifier of the mains supply voltage.
For this reason, in the event of an earth contact, a
continuous fault current may fail to trip a differential
circuit breaker that is only sensitive to alternating
current (type AC).
As the appliance has a single-phase supply, it is
therefore advisable to use a GFCI that is sensitive to
impulse current (type A), identified by the following
symbol: .
Caution : these GFCIs may go under different
names, according to the manufacturer.
Appliances with wobbulators produce a fault
current on the earth wire. This current may be
sufficient to trip the differential circuit breaker
unnecessarily. This may occur if :
• Several variable-speed appliances are connected
to the same GFCI.
• The appliance produces a fault current that is
above the GFCI’s actual trip threshold.
Caution : As there are manufacturing tolerances,
the actual trip threshold of a GFCI will be between
50% and 100% of its theoretical nominal threshold.
Should a problem arise, measure the fault current
and the GFCI’s actual trip threshold.
You can begin by consulting the characteristics of
your appliance in the table below :
Appliance Mains supply
Conductor
Cross-section
(mm2)
GFCI (Ph + N)
Gauge
(A)
Threshold
(mA)
Blixer®5 V.V.
Blixer®7 V.V.
220 - 240V
50 or 60 Hz
single-phase
2,5 B 20 ≥30

6
04/09/2020
UNPACKING
• Carefully remove the equipment from the
packaging and take out all the boxes or packets
containing attachments or specific items.
• WARNING - some of the tools are very sharp
e.g. blade, discs...
INSTALLATION
• We recommend you install your machine on a
perfectly stable solid base.
CONNECTION
• Always check that your mains supply corresponds
to that indicated on the rating plate on the motor
unit and that it can take the amperage.
• The machine must be earthed.
• With the three-phased version, always check that
the blade rotates in an anti-clockwise direction.
HANDLING
• Always take care when handling the blades or
discs - they are very sharp.
ASSEMBLY PROCEDURES
• Follow the various assembly procedures carefully
(see page 8) and make sure that all the attachments
are correctly positioned.
USE
• Never try to override the locking and safety
systems.
• Never introduce any object into the container
where the food is being processed.
• Never push the ingredients down with your hand.
• Do not overload the appliance.
• Never switch the appliance on while it is empty.
CLEANING
• As a precaution, always unplung your appliance
before cleaning it.
• Always clean the appliance and its attachments at
the end of each cycle.
• Never place the motor unit in water.
• For parts made of aluminum alloys, use cleaning
fluids suitable for aluminum.
• For plastic parts, do not use detergents that are
too alkaline (i.e., containing too much caustic soda
or ammonia...).
• Robot-Coupe can in no way be held responsible
for the user’s failure to follow the basic rules of
cleaning and hygiene.
MAINTENANCE
• Before opening the motor housing, it is absolutely
vital unplung the appliance.
• Check the seals and washers regularly and
ensure that the safety devices are in good working
order.
• It is particularly important to maintain and check
the attachments since certain ingredients contain
corrosive agents e.g. citric acid.
• Never operate the appliance if the power cord
or plug has been damaged in any way or if
the appliance fails to work properly or has been
damaged in any way.
• Do not hesitate to contact your local Maintenance
Department if something appears to be wrong.
WARNING: In order to limit accidents such as electric shocks or personal injury, and in order to limit material damage due to misuse of the
appliance, please read these instructions carefully and follow them strictly. Reading the operating instructions will help you get to know your
appliance and enable you to use the equipment correctly. Please read these instructions in their entirety and make sure that anyone else who
may use the appliance also reads them beforehand. Our equipment is designed for professional use and must not be used by children under
any circumstances.
IMPORTANT WARNING WARNING
KEEP THESE INSTRUCTIONS
IN A SAFE PLACE

7
04/09/2020
INTRODUCTION TO YOUR NEW
Blixer®5 g• Blixer®5 V.V. g•
Blixer®7 • Blixer®7 V.V. TABLE-
TOP CUTTER MIXER
ROBOT-COUPE has developed a new concept in
appliance: the Blixer®.
The Blixer®combines the features of two well-known
appliances: the cutter and the blender-mixer.
The Blixer®is perfectly geared to professional
needs. It can perform any number of tasks which
you will soon discover as you use it.
The Blixer®will make it easy to prepare mixed
liquid or semi-liquid, raw or cooked meals.
The Blixer®replace the blender which does not
give entire satisfaction because of its incapacity to
process solid foods.
Thanks to its simple design, all components
requiring frequent handling for maintenance or
cleaning are easily fitted or removed.
To make things easier for you, this manual gives a
breakdown of all the various fitting operations.
This manual contains important information designed
to help the user get the most out of their device.
We therefore recommend that you read it
carefully before using your machine.
SWITCHING ON
THE MACHINE
• ADVICE ON ELECTRICAL CONNNECTIONS
Before plugging in, check that your power supply
corresponds to that indicated on the machine’s
identification plate.
• Blixer®5 Single phase
ROBOT-COUPE appliances are fitted with the
following types of moto:
230 V / 50 Hz / 1
220 V / 60 Hz / 1
The machine comes with a single phase plug
connected to a power cord.
• Blixer®5 V.V. • Blixer®7 V.V. Single phase
The models are available with a single phase
motor: + variable speed: 230 V / 50 - 60 Hz /1
The standardized plug must be calibrated to a
minimum of 16 amps and preferably 20 amps, if
the appliance is used intensively.
• ENERGY SAVING MODE FOR Blixer®5 - Blixer®7
After the food processor is plugged in, it needs to be
switched on by pressing the “on” button I.
If the processor is not used for 5 minutes, it will go
into energy saving mode.
The “on” button needs to be pressed again to switch
on the power supply.
• CONTROL PANEL
Red switch = Off switch
Green switch I = Start speed 1
Black switch = Pulse control
Blixer®5 - Blixer®7 :
Green switch II = Start speed 2
Blixer®5 V.V. - Blixer®7 V.V. :
Speed variation from 300 to 3,500 rpm.
Blixer®5 • Blixer®7 Three phase
ROBOT-COUPE appliances are fitted with the
following types of motor:
230-400 V / 50 Hz / 3
400 V / 50 Hz / 3
220 V / 60 Hz / 3
380 V / 60 Hz / 3
This machine is supplied with a cable to which you
simply attach the appropriate electrical plug or
isolator for your system. The cable has four wires,
one earth wire, plus three phases wires.
If you have a 4-pin plug:
1) Connect the green and yellow earth wire to the
earth pin.
2) Connect the three other wires to the remaining
pins.
If you have more than 4 pins in the plug, please
note the ROBOT-COUPE does not require a neutral
wire.
Switch on the empty machine, making sure that
the blade is rotating properly in an anti-clockwise
direction.
On the motor unit and on the lid a arrow marks the
blade rotation directions.
If the blade turns in a clockwise direction, swap
over two wires.
GREEN YELLOW is the earth,
DO NOT DISCONNECT
Swap either : the ➊and the ➋
the ➋and the ➌
the ➊and the ➌
This appliance must be plugged into an
earthed socket (risk of electrocution).
WARNING

8
04/09/2020
e) Standby Mode
If the food processor is not used for more than 10
minutes (motor not operating), the timer goes into
Standby Mode. Standby Mode can be cancelled by
pressing any button or the “on” button.
f) Turning off the timer:
If you do not want to use the timer, you can
deactivate it by pressing the “on” and “off” buttons
at the same time for several seconds.
Repeat the operation to reactivate the timer
function.
ASSEMBLY
1) With the motor base
facing you, position the
cutter bowl on the motor
base.
Turn the bowl to the right
until it locks.
2) Engage the blade on the motor shaft and lower it
right to the bottom of the
bowl.
Make sure that it is
correctly positioned, by
rotating it in the bowl.
• TIMER
How the timer works
The timer has three 7-segment LED displays, two
timer adjustment buttons and a buzzer.
a) Countdown
When the food processor is switched on, the timer
usually displays 0.00 and can be set directly. This
is called Countdown Mode. The timer increments
one second at a time when the motor is operating.
Incrementation stops if the motor stops then
resumes when the motor starts again. In the case of
models Blixer®5 V.V. and Blixer®7 V.V., the food
processor automatically stops after 9 minutes and
the timer stops. In the case of models Blixer®5 and
Blixer®7, the food processor automatically stops
after 5 minutes and the timer stops.
b) Timer
Before starting, the user can adjust the processing
time to anywhere between 0.05 (5 seconds) and
9.00 (9 minutes) by pressing the +and −buttons.
When the motor starts, the timer increments one
second at a time. This is called Timer Mode.
Countdown stops if the motor stops and resumes
when the motor starts again. When the countdown
gets to 0.00, the processor stops and a buzzer
sounds. The time initially set is then displayed again.
c) Starting the processor with the Pulse button:
If the food processor is started using the Pulse button,
the timer goes into Countdown Mode when the Pulse
button is held down and returns to the previous timer
display when the Pulse button is released.
d) Reset
If the timer displays anything other than 0.00 when
the motor is not operating, the user can reset the
display to zero by pressing the +and −buttons at
the same time or by pressing the “off” button on the
food processor for 2 seconds.
3) Put the lid equipped
with the Blixer®arm on
the bowl (see page 10)
and turn to the right until
locked in place.
The device is now ready
for use.
USES & EXAMPLES
The Blixer®will enable your to perform all your
cutting tasks in minimum time, we recommend
therefore, that you keep a close eye on the mixture
in order to obtain the desired results.
HOSPITAL USES
SPOON FEEDING
• Minced foods: meat, fish... • Vegetable purees
• Mousses: vegetables, fish... • Compotes of stewed fruit
SEMI-LIQUID FEEDING
This simply entails diluting spoon-feeding preparations:
• Minced meat + gravy • Puree + liquid (broth, milk...)
• Soups / creamed soups • Fruit compotes + syrup or water
LIQUID FEEDING (for use via tubes)
• Soups and any preparations that can be liquidized.
RESTAURANTS AND DELICATESSEN USES
• Butter mixtures: snail butter, salmon butter, anchovie
butter…
• Sauces: green sauce, mayonnaise, remoulade, ailloli,
emulsify sauces with tomatoes, cream, parsley…
• Grinding: lobster, scampi, seashells....

9
04/09/2020
• MOTOR BASE
Never immerse the motor base in water. Clean
using a damp cloth or sponge.
• BOWL
After removing the lid, remove the bowl from the
motor base by pushing the trigger fitted in the
handle. Pull up to disengage, leaving the blade
in the bowl in order to prevent any spillage when
working with liquids.
If the food has a solid consistency, remove the
blade and empty the bowl.
Replace the bowl, place the blade back on the shaft
and switch on the machine in order to remove any
mixture which may have stuck to the blade.
If you wish, you can rinse the bowl by filling it with
hot water and switching on for a few minutes.
• BLADE
The stainless steel blade of Blixer®7 and Blixer®7 V.V.
is easy to dismantle and to clean.
After cleaning the blade, always dry the blades well
to prevent rusting.
Ensure power supply to machine is
disconnected.
1 - Place blade dismantling tool over shaft onto
motor base.
2 - Place blade on shaft.
3 - Place dismantling tool in hole over blade
nut and turn anti-clockwise to unscrew. To
remount, carry out operation in reverse.
In both cases, blade is supported by small
knob on blade dismantling tool.
A- Upper blade with sharp edge away from you .
B-
Lower blade with sharp edge towards you .
C- Depending on space required between
blades during reassembly, assemble spacers
Cas follows:
C1 if spacer is placed above blade
C2 if spacer is placed below blade.
PHARMACEUTICAL AND
CHEMICAL LABORATORY USES
• Grinding: herbs, seeds, powders, tablets....
• Mixing: homogeneization of creams, ointments, mixed
components, varied ingredients...
The blade must always be removed for cleaning
HYGIENE
At each step of food processing, the machine and
attachments must be clean.
A certain order when processing foods must be
followed. In general, always try to process foods
that are least likely to cause cross-contamination
first, as illustrated in the following example :
1 - Cooked meat
- Terrines/mousses
- Delicatessen
• ham
• smoked ham
• sausage.
2 - Cheese
• hard
• other type.
3 - Vegetables.
It is vital that all parts of the machine that come into
contact with food are cleaned meticulously, using a
detergent/sanitiser, after each processing job.
• WARNING: NEVER USE PURE BLEACH.
Always follow the detergent manufacturers instructions
to make up the correct strength of solution; these are
normally found on the detergent package, if in doubt
contact your detergent supplier or manufacturer.
- If necessary rub well with a soft brush or cloth:
NEVER use a harsh abrasive cleaning pad.
- Allow the detergent/sanitiser to work for the
required length of time.
- Always rinse well.
- Dry well with a soft clean cloth. Only air dry if the
detergent manufacturer recommends it.
CLEANING
As a precaution, always unplug your appliance
before cleaning it (risk of electrocution).
WARNING

10
04/09/2020
Rubber piece to scrape
the bowl
Rubber pieces to
scrape the lid.
The motor seal can be easily replaced without
having to remove the motor, so we strongly advise
you to ensure that is in good condition.
TECHNICAL
SPECIFICATIONS
• WEIGHT
Net Gross
Blixer®5 g21,2 kg 23,7 kg
Blixer®5 V.V. g21,7 kg 24,2 kg
Blixer®7 21,5 kg 24 kg
Blixer®7 V.V. 22 kg 24,5 kg
• DIMENSIONS (in mm)
• MOTOR SEAL
In order to keep the motor completely watertight,
it is advisable to check the motor seal regularly for
wear and tear and replace if necessary.
The seal must be replaced once a year and once
every 6 months in the case of intensive use.
• WORKING HEIGHT
We recommend that you position the machine on a
stable worktop so that the upper edge of the large
feed hopper is at a height of between 1.20 m and
1.30 m.
A
B
D
C
Blixer®5 - Blixer®5 V.V.
A= 540
B= 340
C = 265
D = 265
Blixer®7 - Blixer®7 V.V.
A= 570
B= 340
C = 265
D = 265
Drawing 1
Drawing 3
Drawing 2
IMPORTANT
Check that your detergent is suitable for
cleaning plastic parts. Some washing agents
are too alkaline (e.g. high levels of caustic
soda or ammonia) and totally incompatible
with certain types of plastic, causing them to
deteriorate rapidly.
MAINTENANCE
• BLADE
The cutting quality mainly depends on the sharpness
of the blades and degree of wear. The blades
are wearing parts which should be changed from
time to time to ensure consistent quality of the end
product.
• BLIXER®ARM
The Blixer®arm has rubber pieces which are wearing
parts. They must therefore be periodically replaced to
maintain optimum efficiency of the arm.
The rubber pieces are very easy to remove and
remount.
• BLIXER®ARM
To clean the Blixer®arm, dismount as follows:
Hold the Blixer®arm in one hand and the middle of
the blade in the other (drawing 1).
Press the two pieces together and turn the handle 45°
anticlockwise (drawing 2).
The two parts of the Blixer®arm can then be removed
from the lid for cleaning (drawing 3).

11
04/09/2020
WARNING
The blades are sharp and must be handled
with care.
Blixer®5 single-phase machine
Blixer®7 three-phase machine
Blixer®5 V.V. single-phase machine
• NOISE LEVEL
The equivalent continuous sound level when
the machine is operating on no-load is less than
70 db (A).
• ELECTRICAL DATA
Blixer®5 three-phase machine
Motor Speed 1
(rpm)
Speed 2
(rpm)
Intensity
(Amp)
230 x 400 V / 50 Hz
1,500 230V = 4.0
400V = 2.5
3,000 230V = 7.0
400V = 4.0
400 V / 50 Hz 1,500 2.7
3,000 3.4
220 V / 60 Hz 1,800 4.7
3,600 6.5
380 V / 60 Hz 1,800 2.5
3,600 3.4
Motor Speed
(rpm)
Intensity
(Amp)
230 V / 50 Hz 3,000 8.7
220 V / 60 Hz 3,600 9.5
Motor Speed
(rpm)
Intensity
(Amp)
230-120 V / 50-60 Hz 300 to 3,500 5.8
Motor Speed 1
(rpm)
Speed 2
(rpm)
Intensity
(Amp)
230 x 400 V / 50 Hz
1,500 230V = 4.0
400V = 2.5
3,000 230V = 7.0
400V = 4.0
400 V / 50 Hz 1,500 2.7
3,000 3.4
Never try to override the locking and safety
systems.
Never insert an object into the container where
the food is being processed.
Never push the ingredients down with your
hand.
Do not overload the appliance.
Never switch the appliance on when it is empty.
REMEMBER
SAFETY
Blixer®7 V.V. single-phase machine
Motor Speed
(rpm)
Intensity
(Amp)
230-120 V / 50-60 Hz 300 to 3,000 5.8
- Power shown on data plate.
These models are fitted with a magnetic safety
device and motor braking system.
As soon as you open the lid the motor stops.
To restart the machine, simply close the lid and
press the green switch.
In order to avoid splashing when processing liquid
preparation, we recommend you stop the machine
before opening the lid.
All the models are fitted with a thermal cut-out
which automatically stops the motor if the machine
is left on for too long or overloaded.
STANDARDS
Consult the declaration of compliance on page 3.
If this happens, allow the machine to cool
completely before restarting.

TECHNICAL DATA

14
04/09/2020

15
04/09/2020

Head Office, French,
Export and Marketing Department:
48, rue des Vignerons
94305 Vincennes Cedex- France
Tel.: [phone]
Email: [email protected]
Robot-Coupe
U.K. LTD:
Fleming Way, Isleworth,
Middlesex TW7 6EU
Tel.: [phone]
Email: [email protected]
Robot Coupe
Australia Pty Ltd:
Unit 3/43 Herbert St
Artarmon NSW 2064 Australia
Tel.: [phone]
Email: [email protected]
Réf. : 451 663 - 04/09/2020