Roca D50010008 User manual

Maxiflow Overflow Bath Filler And Waste
D50010008
Installation And Operating Instructions
Inlet Connections:
1½"
Features:
Technical Specification
Working Pressure:
Min:
Max:
Operating Temperature:
Hot:
Cold:
0.5 Bar
5.0 Bar
70⁰C
5⁰C
WWaarrrraannttyy IInnffoorrmmaattiioonn
Proof of purchase will be required.
The guarantee does not cover faults or damage caused by incorrect
installation and/or maintenance, ordinary wear and tear, water
composition, etc.
*Please see www.uk.roca.com for full terms and conditions of warranty
CClleeaanniinngg
Your product has a high-quality finish and should be treated with care
to preserve the visible surfaces. Never use abrasives or abrasive
cleaning agents to clean this product clean regularly with
contamination free warm water and a damp soft cloth. Do not use
products containing chlorine bleach or hydrochloric acid as these can
damage the product.
We have a policy of continuous improvement and reserve the right to
change specifications without notice.
ROCA
Customer Care Line
TEL: [phone]
INST D50010008
29/04/2021
•Operated by over flow allowing hands free
drainage

P2 P7
C
C
o
o
n
n
t
t
e
e
n
n
t
t
s
s
Congratulations on your purchase of your NEW Maxiflow Overflow Bath
Filler And Waste.
Our fitting instructions have been created with you in mind to provide
you with all the information you require and, if you need any further
help, please don't hesitate to contact our customer care team on 01530
830080
P
P
L
L
E
E
A
A
S
S
E
E
R
R
E
E
T
T
A
A
I
I
N
N
T
T
H
H
I
I
S
S
D
D
O
O
C
C
U
U
M
M
E
E
N
N
T
T
F
F
O
O
R
R
F
F
U
U
T
T
U
U
R
R
E
E
R
R
E
E
F
F
E
E
R
R
E
E
N
N
C
C
E
E
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
:
:
Please read all of the instructions before installation.
Roca recommends this product is installed by a competent person in
compliance with all relevant regional regulations.
Remove all packaging and check the components for damage before starting
installation.
This product must not be modified in any way as this will invalidate the
guarantee.
It is the responsibility of the installer to ensure a waterproof seal is achieved,
after installation all connections must be checked for leaks.
All outlets used primarily for personal hygiene shall deliver water at a safe
temperature as per regional regulations.
Before commencing installation of the new product, ensure that the system
has been flushed to remove any debris, which could cause damage to the
valves and invalidate the warranty.
L
>1,5°1,5°

P6 P3
L
L
i
i
n
n
e
e
D
D
r
r
a
a
w
w
i
i
n
n
g
g
<6mm
L+ 30mm
Ø40
mmØ40mm
OPTIONAL
Ø40
mm
9, Fit the waste body and flange to the bath securing using screw and washer; ensure sealing
washer is placed through the bath before this is done as shown on diagram. Use a pure
Silicon sealant where necessary.
9, Cut any excess tube and fit into waste body using washer and nut
provided.
58
G 1” 1/2
L
G 1/2”
42.5

P4
P5
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
o
o
f
f
o
o
v
v
e
e
r
r
f
f
l
l
o
o
w
w
1, Connect flexible tube to outlet. 2, Connect flexible connector to elbows.
3, Fit the overflow waste body to the
bath ensuring overflow washer is in
place.
4, Turn the filter retaining nut
clockwise, to secure in place.
4 Nm
max 5 Nm
5, Tighten the nut to 4Nm
6, Fasten the .. to the rear of the handle,
tight and secure into place with allen key.
7, Place handle and fixing through the
hole in overflow waste body.
8, Click into place

P4 P5
IInnssttaallllaattiioonn ooff oovveerrffllooww
1, Connect flexible tube to outlet. 2, Connect flexible connector to elbows.
3, Fit the overflow waste body to the
bath ensuring overflow washer is in
place.
4, Turn the filter retaining nut
clockwise, to secure in place.
4 Nm
max 5 Nm
5, Tighten the nut to 4Nm
6, Fasten the .. to the rear of the handle,
tight and secure into place with allen key.
7, Place handle and fixing through the
hole in overflow waste body.
8, Click into place

P6
P3
LLiinnee DDrraawwiinngg
<6mm
L+ 30mm
Ø40
mmØ40mm
OPTIONAL
Ø40
mm
9, Fit the waste body and flange to the bath securing using screw and washer; ensure sealing
washer is placed through the bath before this is done as shown on diagram. Use a pure
Silicon sealant where necessary.
9, Cut any excess tube and fit into waste body using washer and nut
provided.

P2 P7
CCoonntteennttss
Congratulations on your purchase of your NEW Maxiflow Overflow Bath
Filler And Waste.
Our fitting instructions have been created with you in mind to provide
you with all the information you require and, if you need any further
help, please don't hesitate to contact our customer care team on 01530
830080
PPLLEEAASSEE RREETTAAIINN TTHHIISS DDOOCCUUMMEENNTT FFOORR FFUUTTUURREE RREEFFEERREENNCCEE
IIMMPPOORRTTAANNTT:: Please read all of the instructions before installation.
Roca recommends this product is installed by a competent person in
compliance with all relevant regional regulations.
Remove all packaging and check the components for damage before starting
installation.
This product must not be modified in any way as this will invalidate the
guarantee.
It is the responsibility of the installer to ensure a waterproof seal is achieved,
after installation all connections must be checked for leaks.
All outlets used primarily for personal hygiene shall deliver water at a safe
temperature as per regional regulations.
Before commencing installation of the new product, ensure that the system
has been flushed to remove any debris, which could cause damage to the
valves and invalidate the warranty.
L
>1,5°1,5°

Maxiflow Overflow Bath Filler And Waste
D50010008
Installation And Operating Instructions
Inlet Connections:
1½"
Features:
Technical Specification
Working Pressure:
Min:
Max:
Operating Temperature:
Hot:
Cold:
0.5 Bar
5.0 Bar
70⁰C
5⁰C
W
W
a
a
r
r
r
r
a
a
n
n
t
t
y
y
I
I
n
n
f
f
o
o
r
r
m
m
a
a
t
t
i
i
o
o
n
n
Proof of purchase will be required.
The guarantee does not cover faults or damage caused by incorrect
installation and/or maintenance, ordinary wear and tear, water
composition, etc.
*Please see www.uk.roca.com for full terms and conditions of warranty
C
C
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Your product has a high-quality finish and should be treated with care
to preserve the visible surfaces. Never use abrasives or abrasive
cleaning agents to clean this product clean regularly with
contamination free warm water and a damp soft cloth. Do not use
products containing chlorine bleach or hydrochloric acid as these can
damage the product.
We have a policy of continuous improvement and reserve the right to
change specifications without notice.
ROCA
Customer Care Line
TEL: [phone]
INST D50010008
29/04/2021
•Operated by over flow allowing hands free
drainage