Roca Danube T D50010004 User manual

Danube T Shower Kit_D50010004
Min 0.3 bar required
Please retain this document
for future reference.
This product should be fitted
in compliance with Water
Regulations, by a qualified
Please retain this document
for future reference.
This product should be fitted
in compliance with Water
Regulations, by a qualified
plumber.
Use only a clean damp cloth
to maintain the surface
finish, use of abrasive
cleaning materials will
invalidate your guarantee.

Select location for kit, ensuring no wiring
or pipework in the wall can be damaged,
also that when the slider bracket is
positioned at the top of the rail, the hose
is not over extended.
The location should also ensure that
during use, the water flow is directed
toward a suitable location, so as not to
cause water damage.
Remove the caps from the end brackets
using a sharp blade, taking care not to
damage the product.
Once both end brackets have been
secured, push empty rail through end
bracket, until end is part way between
end brackets, then install slider, soap
dish and hose retainer.
When rail components have been
installed, push the rail through the
second end bracket.
To secure the rail, place the small black
rubber stopper into the threaded hole in
the front of the end bracket, then fit the
small brass screw and tighten using a
screw driver, until tight against the rail,
do not overtighten, then fit chrome caps.
Fit hose seals to both ends of shower
hose.
Thread the hose through the hole in the
hose retainer.
Screw the cone end of the hose to the
handset.
Select location for kit, ensuring no wiring
or pipework in the wall can be damaged,
also that when the slider bracket is
positioned at the top of the rail, the hose
is not over extended.
The location should also ensure that
during use, the water flow is directed
toward a suitable location, so as not to
cause water damage.
Remove the caps from the end brackets
using a sharp blade, taking care not to
damage the product.
Mark the required position of the end
brackets on the wall (the centre to centre
dimension is variable, max 600mm)
Once marked, drill hole and fit wall plugs.
Using screws provided, fit end brackets
in desired location.
Once both end brackets have been
secured, push empty rail through end
bracket, until end is part way between
end brackets, then install slider, soap
dish and hose retainer.
When rail components have been
installed, push the rail through the
second end bracket.
To secure the rail, place the small black
rubber stopper into the threaded hole in
the front of the end bracket, then fit the
small brass screw and tighten using a
screw driver, until tight against the rail,
do not overtighten, then fit chrome caps.
Fit hose seals to both ends of shower
hose.
Thread the hose through the hole in the
hose retainer.
Screw the cone end of the hose to the
handset.
Screw the opposite end of the hose to
the mixer.
Locate the hose cone into the slide
bracket, ensuring that it is fully inserted.
If the cone is not fully inserted, the
handset may fall out during use.
To adjust the angle of the handset,
gently move the handset just above the
slider.
To move the slider, press the button and
push or pull the slider, you must always
press the button to move the slider.

Danube T Valve
OPERATING SPECIFICATION
Pressure
Minimum working pressure - 0.3 bar
Recommended working pressure 0.5 - 3 bar
Maximum working pressure - 5 bar
(Pressure above 5 bar must be reduced via a pressure reducer)
In order to assure maximum efficiency of the mixer, the operating pressures
should be balanced.
Water temperature
Inlet hot water supply IMPORTANT
Maximum 85c A minimum 10c difference between outlet
Recommended 65c temperature and hot supply temperature
must be maintained at all times
Inlet cold water supply
10c - 25c
Guarantee
Your product comes with a 5 year guarantee, this includes 2 years parts and labour
followed by a further 3 years parts only, subject to the following:
Proof of purchase will be required.
The guarantee does not cover faults or damage caused by incorrect installation
and/or maintenance, ordinary wear and tear, water composition etc, including:
Supply pipes reversed
Incorrect pressure or temperature
Incorrect use
Foregin bodies and/or scale due to the water composition.
Incorrect cleaning
Cleaning should be carried out using a clean damp cloth, use of abrasive
agents or materials on the product, will invalidate your guarantee.

Maintenance Installation
To replace the thermostatic cartridge; (See diagram)
Turn off water supply
Remove the handle cap , followed by the screw
Inside the handle, remove the screw Prepare the supply pipes at 150mm centres, allowing approx 22mm of pipe to exposed
Pull handle from mixer from the finished wall.
Take note of the stop ring position for re-assembly after maintenance The pipework must be flushed prior to installation.
Remove the cartridge from the mixer body.
After flushing the pipework, install the mixer as a standard exposed fitting, with the outlet
Clean or replace the cartridge as necessary, then replace, ensuring components are located facing downwards.
correctly to give correct maximum set temprature.
The hot supply pipe must be connected to the hot inlet of the mixer, indicated by the red dot.
If re-calibration is required follow instruction in "operation and setting" Place the mounting plate over the pipe end and mark drill holes, ensuring no pipes or
Once water supply is turned on check for leaks. wires are affected.
Once holes are marked remove and drill holes, then fit wall plugs,
Next place the mounting plate over pipe end and locate over drill holes, secure using
screws provided.
Place olive over pipe end and then fit threaded union, tighten using a two spanners one
on the flats of the union the other on the flat of the mounting plate.
Tighten until fully secured, to create a compression fitting seal.
Once secured, screw the trim onto the threaded union and screw up to finished wall
(if required sealant can be used)
(if required sealant can be used)
Place seals into mixer inlets and connect
mixer to union and secure using a spanner
(take care not to damage product finish)
Once all connections
have been made
turn on water supply to
check for leaks,
ensuring the valve is
in the OFF position

Operation and Setting Maintenance
To control the temperature of the shower, turn the left handle for more hot To replace the flow control valve:
or cold water, in the direction indicated by the marking. Turn off water supply
Remove handle by forcing off handle cap
To control the flow of water turn the handle to regulate the flow of water from the Inside the handle, remove the screw
shower in the direction shown on the mixer. Pull handle from valve.
Take note of stop ring positioning for re-fit
The product also has override buttons, the flow control allows for Pull off stop ring.
reduced flow, to activate full flow, press the button and continue Remove valve from mixer, using a spanner unscrew the nut
to turn the handle then unscrew the valve, taking care not to damage the pipe work
The temperature control allows for a temperature stop position Clean or replace valve as necessary.
this can be exceeded by pressing the button and continuing to Replace all components, turn on water supply and check for leaks.
turn the handle
If on installation the temperature is not to your requirement, this can be re-calibrated.
Turn temperature handle to fully hot.
Remove the handle cap , followed by the screw
Pull handle from valve.
Pull handle from valve.
Turn the spindle on the thermostat until the desired temperature is reached.
(Always maintain the 10c difference between supply and mixed)
Once the temperature is reached, replace the handle so that the stop is in the maximum
position, replace screw and handle cap.
Re-calibration should only be carried out when absolutely necessary