Roca W12 User manual

141009
WIPER MOTOR | W12
Installation Instructions
Before installation please read these instructions.
www.rocaindustry.com
■2 Speed, self-parking
■Torque 12Nm
■Wiper shaft in stainless steel
■Adjustable sweep angle: 45 - 110°
■Changeable self-parking, right and left position.
■Insulated ground.
■EMC protected
■IP65
■Powers up to 610mm/560mm - Arm/blade combinations
145c/c
170
27
100
L1
L259
13,8
Accessories
Wiper arm - Std
Wiper arm - Adjustable tip
Wiper arm - Pantograph
Wiper blade
Wiper control
Current diagram: 12 V 24 V
No load < 2 A < 1 A
Rated < 4 A < 2 A
Stall < 9 A < 4,5 A
Fuse (Fast blow) 5 A 3 A
Speed no load (35 / 55 RPM)
Variations:
Max length: Voltage input:
L1 L2 12 V 24 V
16 43 533011 533012
42 68 533021 533022
68 94 533031 533032
Limited warranty
- Roca warrants the wiper motors to be free
from defective material and workmanship
for a period of 3 years from the date of
purchase.
- This warranty does not apply to failure or
damage caused by improper installation,
misuse, lightning strike or damage from
a power surge.
- If failure occurs during this period, return
it to your dealer for repair or replacement.
13,8
Ø/ z=72

Standard arm Pantograph arm Arm with adjustable tip
End
position
Centerline for sweeparea
Instructionsheet
+ -
Battery
Fuse
P
G
FS
+ -
Battery
Fuse
G
FS P
Switch circuit
P = Parking
S = Slow
F = Fast
G = Ground
Centerline for sweep area
Wiperarm
Right park pos.
CCW
Mounting instructions W12 - wiper motor
(Keep battery main switch turned off during operation inside of the wiper motor)
1. Remove cover with enclosed torx key.
2. Locate the mounting position and using the template provided on box, drill mounting holes
and mount motor to the surface. See picture 1.
3. The motor is pre-set to 45°sweep and right parking position.
4. Attache the wiper arm with help of template on instruction sheet. See picture 2 and 3.
Don't mix up the centerline of the sweep area with centerline of the windshield.
Centre line is needed to find the right position of arm on the windshield.
Find the centerline of the sweep area.
5. Loosen the two screws on the angle plate. See picture 5. Move the arm to desired end
position of sweep area. See picture 4. Tighten the two screws firmly.
6. To set the self-parking feature to park in the left position use the enclosed torx key
and turn the parking selector clockwise. See picture 5.
7. Connect wires as shown in picture 6.
If using Roca switch 466099/466208 use 6a. For all other switches use 6b.
Use a 5 Amp fuse for 12 V. and 3 Amp for 24 V.
8.Make sure the gasket is in right position and replace the cover on the motor with the
screws taken out.
Note: If the arm sweeps too far out on both sides, the sweep angle needs to be reduced,
repeat point 5 above. If the arm goes too far on one side only then you didn't start with
the arm in center of the sweep. Remove the arm and place it at the correct position.
Parking selector
Angle plate
22,5°
22,5°
22,5°
3a 3b 3c
45
Switch 466099
Actuator 466026
6a 6b
22,5°
1
2
Alternative fastening.
145c/c
176 -
FS
G
P
5

Standard arm Pantograph arm Arm with adjustable tip
End
position
Centerline for sweeparea
Instructionsheet
+ -
Battery
Fuse
P
G
FS
+ -
Battery
Fuse
G
FS P
Switch circuit
P = Parking
S = Slow
F = Fast
G = Ground
Centerline for sweep area
Wiperarm
Right park pos.
CCW
Mounting instructions W12 - wiper motor
(Keep battery main switch turned off during operation inside of the wiper motor)
1. Remove cover with enclosed torx key.
2. Locate the mounting position and using the template provided on box, drill mounting holes
and mount motor to the surface. See picture 1.
3. The motor is pre-set to 45°sweep and right parking position.
4. Attache the wiper arm with help of template on instruction sheet. See picture 2 and 3.
Don't mix up the centerline of the sweep area with centerline of the windshield.
Centre line is needed to find the right position of arm on the windshield.
Find the centerline of the sweep area.
5. Loosen the two screws on the angle plate. See picture 5. Move the arm to desired end
position of sweep area. See picture 4. Tighten the two screws firmly.
6. To set the self-parking feature to park in the left position use the enclosed torx key
and turn the parking selector clockwise. See picture 5.
7. Connect wires as shown in picture 6.
If using Roca switch 466099/466208 use 6a. For all other switches use 6b.
Use a 5 Amp fuse for 12 V. and 3 Amp for 24 V.
8.Make sure the gasket is in right position and replace the cover on the motor with the
screws taken out.
Note: If the arm sweeps too far out on both sides, the sweep angle needs to be reduced,
repeat point 5 above. If the arm goes too far on one side only then you didn't start with
the arm in center of the sweep. Remove the arm and place it at the correct position.
Parking selector
Angle plate
22,5°
22,5°
22,5°
3a 3b 3c
45
Switch 466099
Actuator 466026
6a 6b
22,5°
1
2
Alternative fastening.
145c/c
17
6 -
FS
G
P
5

141009
WIPER MOTOR | W12
Installation Instructions
Before installation please read these instructions.
www.rocaindustry.com
■2 Speed, self-parking
■Torque 12Nm
■Wiper shaft in stainless steel
■Adjustable sweep angle: 45 - 110°
■Changeable self-parking, right and left position.
■Insulated ground.
■EMC protected
■IP65
■Powers up to 610mm/560mm - Arm/blade combinations
145c/c
170
27
100
L1
L259
13,8
Accessories
Wiper arm - Std
Wiper arm - Adjustable tip
Wiper arm - Pantograph
Wiper blade
Wiper control
Current diagram: 12 V 24 V
No load < 2 A < 1 A
Rated < 4 A < 2 A
Stall < 9 A < 4,5 A
Fuse (Fast blow) 5 A 3 A
Speed no load (35 / 55 RPM)
Variations:
Max length: Voltage input:
L1 L2 12 V 24 V
16 43 533011 533012
42 68 533021 533022
68 94 533031 533032
Limited warranty
- Roca warrants the wiper motors to be free
from defective material and workmanship
for a period of 3 years from the date of
purchase.
- This warranty does not apply to failure or
damage caused by improper installation,
misuse, lightning strike or damage from
a power surge.
- If failure occurs during this period, return
it to your dealer for repair or replacement.
13,8
Ø/ z=72